FPV Model Skywalker X8 Installation guide

Brand
FPV Model
Model
Skywalker X8
Type
Installation guide
Skywalker X8 Installation Manual
Thank you for Purchasing the Skywalker X8 FPV Plane from FPV Model. The Skywalker X8 is specially designed for First
Person View (FPV) purpose.
Technical Parameters
Wingspan: 2120mm
Weight: 880G
Take-off weight:3200G
Required Parts
Motor: 2820 KV730
ESC: 60A
Battery Pack: 4S 8000MAH
Propeller: 12X6~13X8
1
WWW.FPVMODEL.COM
KIT version configuration: Fuselage, wing, wing let, tube, accessories bag, sticker
Parts Listing
2
WWW.FPVMODEL.COM
Assembly
Glue the winglet layers, spread the glue evenly over the wing and both sides of the layers ( the layer marked with T board
belongs to parts of the main wing).
3
WWW.FPVMODEL.COM
Wait for 5 minutes to allow glue to dry until it is non-sticky, then they can be glued in alignment.
4
WWW.FPVMODEL.COM
Glue the hatch magnets , after compressing the magnet tightly, fix them with CA glue.
5
WWW.FPVMODEL.COM
Glue the wood chip onto the hatch and fuselage, pay attention to the direction of SN of the magnetic pole
6
WWW.FPVMODEL.COM
After gluing, put it together and inspect the mounting spacing.
Glue the servo, please choose the standard servo provided by skywalker or servo with moment more than 2.5 KG
7
WWW.FPVMODEL.COM
Glue the rudder horn, spread the glue evenly and wait for its dryness, then Glue the rudder horn
8
WWW.FPVMODEL.COM
Power on the servo and place it in the mid-position , then lock the regulator screw, tighten the steel wire. And shorten the extra
length of the wire.
9
WWW.FPVMODEL.COM
Glue the fixed layer of the winglets, please be sure to spread the glue evenly and wait until it is completely dry, afterwards you
can glue the layer.
10
WWW.FPVMODEL.COM
Cut out the pre-reserved slot on the aileron only about 1,5 mm wide by a new blade.
11
WWW.FPVMODEL.COM
Wing plate bonding, please to smear evenly on all surfaces, please not to spread the glue over the tube slot!
Settle the extending line in the line slot previously and spread the glue evenly over the plate.
12
WWW.FPVMODEL.COM
Wait for the two planes' dryness, later spread some glue over the vertical planes, and then fix and flatten them.
13
WWW.FPVMODEL.COM
The side plate bonding: spread the glue on both sides of the plate
14
WWW.FPVMODEL.COM
It is recommended to insert the tube into the wing to guide the butt plate, which is more accurate.
15
WWW.FPVMODEL.COM
The line slot of early product also need to be widened to let the the extending line with plug directly into the fuselage.
16
WWW.FPVMODEL.COM
Install the motor, and cement it to the fuselage in advance, you can also first fix the layer board base, and afterwards install the
motor.
17
WWW.FPVMODEL.COM
18
WWW.FPVMODEL.COM
Spread the glue on both sides of the fuselage, note:please avoid the tube slot!
19
WWW.FPVMODEL.COM
Page is loading ...
Page is loading ...
Page is loading ...
Page is loading ...
Page is loading ...
Page is loading ...
Page is loading ...
Page is loading ...
Page is loading ...
Page is loading ...
Page is loading ...
  • Page 1 1
  • Page 2 2
  • Page 3 3
  • Page 4 4
  • Page 5 5
  • Page 6 6
  • Page 7 7
  • Page 8 8
  • Page 9 9
  • Page 10 10
  • Page 11 11
  • Page 12 12
  • Page 13 13
  • Page 14 14
  • Page 15 15
  • Page 16 16
  • Page 17 17
  • Page 18 18
  • Page 19 19
  • Page 20 20
  • Page 21 21
  • Page 22 22
  • Page 23 23
  • Page 24 24
  • Page 25 25
  • Page 26 26
  • Page 27 27
  • Page 28 28
  • Page 29 29
  • Page 30 30
  • Page 31 31

FPV Model Skywalker X8 Installation guide

Brand
FPV Model
Model
Skywalker X8
Type
Installation guide
Download PDF
report

Ask a question and I''ll find the answer in the document

Finding information in a document is now easier with AI

Other documents