Net Optics iBYPASS 40G Quick Install Manual

Brand: Net Optics

Model: iBYPASS 40G

Type: Quick Install Manual

Quick Install Guide

I2BP-40

800-0228-001 Rev A 12/13

PLEASE READ THESE LEGAL NOTICES CAREFULLY.

By using the Net Optics iBypassTM 40G Switch, you agree to the terms and conditions of usage set forth by Net Optics,

Inc.

No licenses, express or implied, are granted with respect to any of the technology described in this manual. Net Optics

retains all intellectual property rights associated with the technology described in this manual. This manual is intended

to assist with installing Net Optics products into your network.

Trademarks and Copyrights

Inc. Additional company and product names may be trademarks or registered trademarks of the individual companies

and are respectfully acknowledged.

Additional Information

Net Optics, Inc. reserves the right to make changes in specications and other information contained in this document

without prior notice. Every effort has been made to ensure that the information in this document is accurate.

Contents

iBypass 40G Switch Content 4

iBypass 40G Switch Overview 5

Connect Power 8

Connect Options 10

Congure the IP 14

Assign IP in Web UI 16

Connect to the Network 18

Connect Monitoring Tools 19

iBypass 40G Switch Content

This guide provides the initial steps to set up and congure the Net Optics iBypassTM

40G Switch.

Carefully unpack the contents and verify you have the following components:

• iBypass 40G Switch

• 3-meter RJ45, CAT 5e 4-pair

• RJ45 to DB9 Console Port to PC cable

• Long Ear Extender and Short Ear Extender for rack mounting

• Two External Power Supplies (12VDC, 9A, 108W)

• Eight Phillips screws

• iBypass 40G Switch Quick Install Guide (this document)

• iBypass 40G Switch User Guide (on CD)

• End User Agreement, Registration Card and Extended Warranty (if purchased)

The QSFP+ transceiver kits and 40G MTP cables are sold and shipped separately.

Contact Net Optics Technical Assurance Center if any component is missing or

damaged. Contact details are at the back of this guide.

iBypass 40G Switch Overview

2x16 Character Display

Network

Ports

Monitor

Ports

Bypass, Tap, Power

LEDs

Activity & Alarm

LEDs

Management

Port

Console

Port

Figure 1 - Front View

• Console Port (RJ45) and Management Port (RJ45)

• 2 x 40G Monitor Ports (uses QSFP+ transceivers )

• 2 x 40G Network Ports (MTP Connectors)

Figure 2 - Rear View

• Hot swappable fans and replaceable power module

Step 1

Rack Mount iBypass 40G Switch

Install the iBypass 40G Switch into a standard 19-inch equipment rack. The switch is

designed to occupy one rack unit. Do the following to install the iBypass 40G Switch

into an equipment rack:

1. Remove the Ear Extenders and screws from the shipping bag.

2. Attach the Long Ear Extender to the switch if you are only mounting one switch

or attach the Short Ear Extender between two switches if you are mounting two

switches. See Figure 3.

3. Slide the switches in place in the rack.

4. Fasten the switches in place at the front panel ears using the Phillips screws.

5. Make sure the rack is properly electrically grounded.

Grounding

Ground the chassis to the rack by connecting a 14 AWG minimum ground wire with a

#8 ring lug to the ground connection on the rear of the chassis. Terminate the other

end of the ground wire to the rack ground bus bar.

Long Ear Extender

for one switch

Short Ear Extender

binds two switches

Figure 3 - Use Ear Extenders in Rack Mount Preparation

Step 2

Connect Power

Ensure the iBypass 40G Switch is grounded before connecting power. Do the

following to connect and apply power to the iBypass 40G Switch:

1. Plug one of the supplied power cords to a power connector located at the rear

of the chassis. Plug the other end to a power source. See Figure 4.

2. For redundancy, plug the other power cord to the iBypass 40G. Plug the other

end to a source independent from the rst power source.

The Power LEDs on the front illuminate.

Switch Default Settings

The iBypass 40G Switch ships with the following default system settings:

Management Port IP: 10.60.4.180 Threshold Ports A & 1: 80%

Management Port Netmask: 255.0.0.0 Threshold Port B & 2: 80%

Management Port Gateway: 10.0.0.1 Username: admin

Port Speed (A, B, 1, and 2): 40G Password: netoptics

Figure 4 - Power Connections

Step 3

Connect Options

You have two ways of logging in to the iBypass 40G switch.

Option 1 - Connect PC to Management Port

1. Connect a PC whose IP address is on the same subnet as the iBypass switch.

The default address on the switch is:

IP Address: 10.60.4.180 Mask - 255.0.0.0 Gateway - 10.0.0.1

2. Connect a Cat 5e cable from your PC’s Ethernet port to the iBypass

Management port. See Figure 5.

3. Open a terminal window and ping 10.60.4.180 to conrm the connection.

4. After you have conrmed that you have a connection, you can log in via SSH at

the terminal prompt, or enter the default address into the browser URL. Go to

the Assign IP in Web UI section if you want to log in through the Web UI. Go

to the next step if you want to log in to the CLI.

5. At the terminal window prompt, type ssh [email protected]. Enter

password netoptics. The Net Optics prompt appears.

6. At the prompt, enter admin for the user and netoptics for the password.

7. Change the password for the admin account by entering the following

command at the prompt:

modify user password admin <new_passwd> <re-enter_passwd>

where <new_passwd> is the new password for the admin account and

<re-enter_passwd> is your password entered again.

8. Go to Congure the IP section and follow the instructions to set a new IP

address.

For more information about using the iBypass 40G Switch CLI, enter help to display

command information or see the iBypass 40G Switch User Guide for more details.

PC on the same subnet

as iBypass 40G switch

Connect Cat 5e cable from

Management port to PC

Ethernet

Figure 5 - PC to Console Port

Step 3 (cont.)

Option 2 - Connect PC to the Console Port

1. Connect a PC running terminal emulation software to the iBypass 40G Switch

Console port with the supplied DB9-RJ45 console cable. See Figure 6.

2. Launch the terminal emulation software, such as HyperTerminal or minicom,

and set the communication parameters to 115,200 baud, 8 data bits, no parity,

1 stop bit, and no ow control.

3. At the prompt, enter admin for the user and netoptics for the password.

4. Change the password for the admin account by entering the following

command at the prompt:

modify user password admin <new_passwd> <re-enter_passwd>

where <new_passwd> is the new password for the admin account and

<re-enter_passwd> is your password entered again.

5. Go to Congure the IP section and follow the instructions to set a new IP

address.

For more information about using the iBypass 40G Switch CLI, enter help to display

command information or see the iBypass 40G Switch User Guide for more details.

Computer with terminal

emulation software

DB9 to RJ45 console

cable

Figure 6 - PC to Console Port

Step 4

Congure the IP

The iBypass 40G switch ships with a default address. You can decide to use the

default address, assign a static IPv4 or IPv6 IP address or use DHCP to assign an

address.

To congure the system with a static IPv4 or IPv6 address, do the following:

1. At the CLI prompt, type the following to set the address mode to static:

set network mode static

2. Type the following to set the IPv4 address:

set network ipaddress <d.d.d.d> where <d.d.d.d> is the IPv4 address

3. Type the following to set the network mask:

set network netmask <m.m.m.m> where <m.m.m.m> is the netmask.

4. Type the following to set the gateway:

set network gateway <g.g.g.g> where <g.g.g.g> is the gateway address.

5. Type reboot host, to reboot the system. This is required for the new address to

take effect. The new IP address will display in the LCD.

After setting the IP address, connect the Management port to the network, so

that you can access the device remotely over SSH or launch the Web UI with

the new IP address.

Do the following to congure the system to use a DHCP address:

1. At the CLI prompt, type set network mode dhcp.

2. At the next prompt, type reboot host

3. After reboot, log into the iBypass via the PC connected to the Console port.

4. At the CLI prompt, enter show network. The screen will display the address

that was assigned to the switch.

Assign IP in Web UI

If you want to change the IP address through the Web UI, do the following:

1. Open a browser on a PC connected to the iBypass switch or on the same

subnet, and enter the default IP address in the URL, https://10.60.4.180.

2. At the iBypass log in banner page, enter Username admin and Password

netoptics. The Home page displays. See Figure 7.

3. At the Home page, click on the Conguration tab. The Conguration page

displays. See Figure 8.

4. Select IP version, select Static or DHCP.

5. If you select Static, enter the IP address, netmask, and gateway.

6. Click the Apply button.

7. Click Reboot.

8. After the iBypass has rebooted, enter the new IP address at the URL.

9. Re-log in. The iBypass home page displays.

Figure 7 - Home Page

Figure 9 - Congure IP Web Page

Step 5

Connect to the Network

The iBypass 40G Switch Network ports require 40G MTP cables.

Network port B to

a network switch

or router

Network port A to a

network switch or

router

Figure 10 - MTP Cables to the Network

1. Connect Network Port A to a network device with a 40G MTP cable.

2. Connect Network Port B to another network device using another 40G MTP

cable.

3. Verify that the Network ports are cabled in-line between two network devices.

4. Verify the link status LED illuminates for each connected port.

5. Verify the ACT LED ashes when there is trafc on the network link.

Step 6

Connect Monitoring Tools

Do the following to connect monitoring tools to the iBypass 40G Switch:

Insert transceiver to

Monitor port 1

Insert transceiver to

Monitor port 2

Figure 11 - QSFP Connections to the Monitoring Tools

1. Insert QSFP+ transceivers into Monitor port 1 and Monitor port 2.

2. Connect a cable to Monitor port 1 transceiver and connect the other end to a

monitoring tool.

3. Connect a cable to Monitor port 2 transceiver and connect the other end to

another monitoring tool.

4. Verify that the monitoring tools are receiving trafc from the iBypass 40G

Switch.

www.netoptics.com

If you have questions while your product is under warranty or you are enrolled

in a support plan, please contact the Net Optics Technical Assurance Center

(TAC) via email at [email protected] or by calling +1.408.737.7777,

Monday through Friday, between the following hours in your region:

• 7:00 - 17:30 Americas (Pacic Time)

• 9:00 - 17:00 EMEA (Frankfurt Time)

• 9:00 - 17:00 APAC (Hong Kong Time)

You can also nd more information on our website at www.netoptics.com.

Net Optics iBYPASS 40G Quick Install Manual

Net Optics iBYPASS 40G Quick Install Manual

Net Optics iBYPASS 40G Quick Install Manual

Related papers

Other documents