Craft Dragon ImPress CD-ES 080902 User manual

Brand: Craft Dragon

Model: ImPress CD-ES 080902

Type: User manual

This manual is also suitable for

CD-ES 080902

ImPress

User Manual

Model No: CD-ES 080902

Please read these instructions carefully and keep them for future reference

The manual

Users manual for CraftDragon® Impress and Flexi-bloc™

English version 1.0, January 2011

this publication without obligation to provide notification of such changes.

Craft Dragon does its best to provide current and accurate information within this manual. However, Craft Dragon reserves the right to change

any specifications and product configurations without prior notice and without any obligation to include such changes in this manual.

Reuse, recycling and recovery. You are urged to recycle this product when replacing it with a newer product, or when it has outlived its use-

ful life by bringing it to an appropriate collection point for recyclable materials in your community or region. By doing this you can help improve

the environment of your community as well as minimize the potential negative effects created should any hazardous substance that may possi-

bly be present within waste material reach the environment during the disposal process.

Flexi-bloc is a trademark and CraftDragon is a registered trademark of Craft Dragon Ltd.

Any additional product or company names mentioned in this documentation may be trademarked and/or registered as trademarks. Mention of

any third-party products is for information only and does not constitute either an endorsement nor a recommendation.

Contents

Unpacking your CraftDragon® ImPress...................................2

Safety Instructions....................................................................3

An introduction to the CraftDragon® ImPress..........................5

Feature Diagram......................................................................6

Setting up your ImPress...........................................................7

Using your CraftDragon® ImPress

Thermostat, power switches, Cleaning and Storage..........8

Hot Foil Stamping...............................................................9

Precision Ink Stamping....................................................... 11

Embellishing and Hot Press Printing.................................. 12

DO’S AND DON’TS............................................................ 13

Connection to the Mains Supply.............................................. 14

Unpacking your CraftDragon® ImPress

Thank you for purchasing the CraftDragon® ImPress Hot foiling machine. Each unit has been manufactured to ensure safety and reliability

every ImPress has been thoroughly tested and has been shipped in perfect operating condition. Carefully check the packaging for damage

that may have occurred during transport. If the packaging appears to be damaged, carefully inspect your ImPress for any damage and be sure

all accessories necessary to operate the unit have arrived intact.

• It is recommended that you use Craft Dragon products with your machine, in order to achieve the best results.

•If the unit or accessories have been damaged, you may either return the damaged part to the retailer from which you purchased it or contact

our customer support number (0845 398 7770) for further instructions.

Before first use, please read the instructions carefully, and keep them for future reference.

UNPACKING YOUR CRAFTDRAGON® IMPRESS

1. Carefully Remove the CraftDragon® ImPress Hot foiling machine and positioning unit and all the accessories from the carton and remove

all packaging materials.

2. Make sure that all packaging is disposed of correctly.

3. Check that all of the accessories listed on the contents list below are present.

4. Check the CraftDragon® ImPress after unpacking for any visual damage such as:

Ÿ Misaligned or damaged parts

Ÿ Damage to the plug or cable

5. If you can see any damage do not use the ImPress.

6. Read all safety Instructions before use.

7. Your ImPress system consists of:

• Imp and Press Unit

• Make ready mat

• 1 Die

• 1 roll of foil

Please note:

In manufacture it is necessary to lightly grease some parts of the appliance. This may result in the unit emitting some vapour when

first used, this is normal.

Safety Instructions

IMPORTANT SAFEGUARDS

1. Place the assembled unit on a suitable firm, flat and substantial work surface, at a height that is comfortable for easy operation.

2. Always locate the unit away from the edge of a work surface.

3. Always disconnect the CraftDragon® ImPress from the main supply when not in use and when cleaning.

4. Do not lock down the ImPress whilst the heated Imp unit is still hot.

5. Do not leave the CraftDragon® ImPress on unattended.

6. Never cover the CraftDragon® ImPress when switched on or hot as this may lead to a risk of fire.

7. Make sure that when using the CraftDragon® ImPress for hot foiling the unit is away from flammable or perishable materials.

8. Position the mains lead so that it does not get in your way when using the CraftDragon® ImPress and make sure that the power cable cannot

be damaged by the heated area of the CraftDragon® ImPress.

9. Before use, always place the ImPress unit on a solid, stable surface to avoid tipping or dropping it.

10. Do not touch hot areas of the CraftDragon® ImPress with bare hands when switched on.

11. Use a heat resistant glove or pad when removing dies etc.

12. Keep heated surface away from all personal body parts, animals or children.

13. The CraftDragon® ImPress will become very hot during use.

14. Close supervision is required when the CraftDragon® ImPress is used near or by children.

15. Never allow the cord to touch wet or hot surfaces, become twisted or be within the reach of children or animals.

16. Do not place on or near a hot gas or electric burner.

17. Do not use out of doors, unless under safe conditions.

18. Never use the CraftDragon® ImPress with a damaged cord or plug or after the CraftDragon® ImPress has malfunctioned or been damaged

in any other way.

19. Never attempt to open any part or dismantle the controls of the CraftDragon® ImPress. Responsibility for failure cannot be accepted if these

instructions have been ignored.

20. Do not use the CraftDragon® ImPress for anything other than the intended uses.

21. Only use the heated Imp unit when fixed in the press.

22. Do not remove the locking handles from the press unit.

23. Only use heated unit on recommended materials.

24. This appliance is intended for household, supervised educational or office use only.

25. Do not use the CraftDragon® ImPress in the immediate surroundings of a bath, a shower or a swimming pool.

Safety Instructions

Warning: Any repairs that need to be done to the CraftDragon® ImPress must be referred to an authorised service agent only.

Warning: Never use the CraftDragon® ImPress if the supply cord is damaged. If the supply cord is damaged, it must be replaced by the

Manufacturer or its service agent in order to avoid a hazard.

Warning: The CraftDragon® ImPress is not intended for use by young children or infirmed persons without supervision.

Warning: The CraftDragon® ImPress is not intended for use by persons (including children) with reduced physical, sensory or mental capabilities,

or lack of experience and knowledge, unless they have been given supervision or instruction concerning use of the CraftDragon® ImPress by a

person responsible for their safety.

Your safety

· WARNING: Do not touch hot surfaces. Use oven mitts, oven gloves or a heat resistant mat when removing a hot die or tri-plate

· WARNING: Avoid contact with moving parts.

· To protect against electrical shock, do not immerse cord or plug in water or other liquid.

· Extreme caution must be observed when moving an appliance with hot contents.

· Do not use the appliance with wet or moist hands.

· Always remove the plug from the socket whenever the machine is not in use, or whenever a disturbance occurs. Pull on the plug, not

the cable.

PRODUCT SPECIFICATION

Voltage: 220V -240V - 50 Hz

Power: 250W

What is the CraftDragon® ImPress?

The ImPress from CraftDragon® is a revolutionary, new, ultra-stylish and versatile machine developed to make hot foil stamping easy for

anyone to do. With an easy fix block system and interchangeable accessories it is fun and simple to use. You be able to glide through the

ImPress’ many precision functions and produce stunningly professional finishes which are sure to astound. Not only will the results please

but the ImPress looks are bound to ‘Impress’. Available in 4 different colour ways (subject to availability) the ImPress oozes style from its

design and beautifully sculpted curves to its unique flexible click in system. It is stylish enough to sit in any home, office or workspace and

small and light enough to take with you so that you and your ImPress are always at the ready

Amongst the ImPress’ many innovative features are:

Ÿ Specifically configured print head for easy fix dies so that you are set up in seconds. (1)

Ÿ Simple to read and use temperature control panel, with power switch ,temperature control knob and pilot light. (2)

Ÿ Specially designed removable guide mat to position and hold your work in place. (3)

Large printing deck to support large projects. (4)

Removable printing head (Imp) to give flexibility in printing and other techniques. (5)

Easy to use press to give firm and even pressure without the need for excessive adjustment. (6)

Ÿ Removable flat bed (or platen) to allow easy adjustment and insertion of alternative accessories. (7)

Ÿ Locking Handles for ease of removal of Imp and other accessories. (8)

Ÿ Soft grip handle. (9)

Retaining clips to ensure that the dies do not fall out of the tracks (11)

Extra wide throat for safety and for extra thick substrates. (10)

What can the ImPress be used for?

The CraftDragon® ImPress is designed to be used primarily for Hot foil Stamping, although with its many add-ons and accessories it can

also be used for:

Precision Ink Stamping using the unique Flexi-bloc™ accessory.

Adding embellishments, such as hot-fix crystals and studs to papercraft and fabric projects.

Hot Press printing and other sublimation techniques.

Hot melt techniques (using friendly plastic etc).

AN INTRODUCTION TO THE CRAFTDRAGON® IMPRESS

Feature Diagram

1. Print head

2. Control panel

3. Positioning mat

4. Print Deck

5. Imp

6. Press

7. Flat bed (or platen)

8. Locking Handles

9. Sure grip handle

10. Throat

11. Retaining clips

Control panel detail

Pilot light

Control Dial

Power switch

You will have to experiment with temperature and dwell times, depending on the substrate, foil and room temperature but once you get the hang of it

you will find your ImPress simple and fun to use. Just to make sure you and your ImPress get off on the right footing, follow these simple rules for setting

up to get the best out of your unit right from the start.

Ÿ Make sure the CraftDragon® ImPress is sitting firm and level on a solid surface such as a kitchen worktop, solid desk, table or workbench, as

any give in the supporting surface will affect the resulting print.

Ÿ Make sure that the working height is comfortable, but at the right height to allow you to apply pressure to the press.

Ÿ Keep the room you are working in at a steady temperature if possible.

Ÿ For hot foil stamping, stick the make-ready mat in position on the platen using the following method:

1. Remove the backing sheet from the make ready

2. Trim 2cm off 2 adjacent edges of the backing sheet

3. Reapply the backing sheet to the centre of the adhesive layer of the Make-ready mat.

4. Place the Make-ready mat blue face up and press down the edges to enhance adhesion

Ÿ Before switching on, insert your chosen die in the centre channel.

Ÿ Swivel the retaining clip on the end of the channel into a down position to retain the die in place.

Ÿ Turn the temperature dial up to the required setting and allow the print head to warm through thoroughly for at least 10 minutes (the longer the

better)

Ÿ Test the printing temperature of your foils (normally between 4 and 5 on the dial , depending on the foil and the substrate you are using) before

proceeding to your actual project.

Ÿ You’re ready to go - have fun!

For further hints and tips go to: www.craftdragon.com

Setting up your CraftDragon® ImPress

1 2 3 4

Using your CraftDragon® ImPress

USING THE THERMOSTAT AND POWER SWITCHES

1. The thermostat on the CraftDragon® ImPress can be adjusted to temperature conditions. Cold or hot conditions can affect the working

temperature of the CraftDragon® ImPress. It is advisable to keep the work room at a constant temperature.

2. The power light comes on with a steady glow when the CraftDragon® ImPress is activated.

3. To operate the thermostat, turn dial clockwise to increase the heat output.

4. To decrease the heat, turn the dial anti-clockwise.

5. Once you have finished using the CraftDragon® ImPress always turn the power off and re-set the thermostat to the zero position.

6. Remove any dies with heat resistant glove or pad or when cool.

7. Remember to unplug the CraftDragon® ImPress unit from the mains supply.

SETTING THE TEMPERATURE

CLEANING

1. To clean the CraftDragon® ImPress always disconnect from the mains supply.

2. When the CraftDragon® ImPress is cold, clean the base plate with a damp cloth and buff with a dry cloth.

3. To clean the main body of the CraftDragon® ImPress, follow these instructions.

Ÿ Allow the CraftDragon® ImPress to cool before cleaning.

Ÿ Clean outer surface using a moist cloth and then wipe over with a dry soft cloth.

Ÿ Do not use harsh detergents, abrasives or spray on cleaners.

Ÿ Do not allow water to seep into the openings or come into contact with electrical connections.

STORAGE

1. If possible store in a crafting case or the box it came in.

2. Before storing the CraftDragon® ImPress ensure that it is completely cold.

3. To store both elements together, place a shim between the Imp and the press base to protect both surfaces before locking down.

Dial settings Temperature Discipline

1-2 Low Hot Melt work

3-4 Medium

Sparkle craft

Hot foil stamping

5-6 High

Hot foil stamping

Hot press printing

Using your CraftDragon® ImPress

How to use the CraftDragon® ImPress for Hot foil Stamping

What is Hot Foil Stamping?

Hot Foil Stamping can be used to decorate and embellish many surfaces and add value to any project. Sometimes also known as foil blocking or

hot foil blocking, it is a high added value dry printing process in which the image is transferred to the surface to be printed by a combination of

heat and pressure.

Ÿ It can be used to produce true 'reflective metal' printing, and other effects impossible with ink based systems. As a result, hot foil printing can

be used to enhance and add value to conventionally printed stationery, greetings cards, certificates etc.

Ÿ Being a dry process, there are no problems with fumes or solvent vapours, or mixing inks, and the printed goods can be handled immediately.

Ÿ The printed image is 100% opaque.

The basic kit you will need to Hot Foil Stamp is:

1. CraftDragon® ImPress

2. Die

3. Make Ready Mat

4. Foil

5. Chosen substrate

All of these can be purchased at www.craftdragon.com

Before you plug in the CraftDragon® ImPress refer to the safety instruction section of this user manual.

Make sure the CraftDragon® ImPress is sitting firm and level on a solid surface such as a kitchen worktop, solid desk, table or workbench. Any

give in the supporting surface will affect the resulting print.

1. 2. 3. 4.

How to use the CraftDragon® ImPress for Hot foil Stamping (cont.)

1. Insert your chosen die into the Imp.(1)

2. Apply the Make-ready mat to the flat bed (7) directly below where the Imp or print head will touch.

3. Fix the positioning mat (3), if you have one, around the tower.

4. Plug into the mains and switch on, following safety instructions

5. Switch on power to the CraftDragon® ImPress using the green switch on the control panel. This will light up with a steady glow showing

that power is reaching the unit.

6. The red pilot light will come on to indicate that the unit is heating up.

7. Leave the unit to heat up for at least three cycles (ie the red light going on and off) and preferably for approximately 10 to 15 minutes to

ensure that heat is distributed evenly across the printing surface to give the best result.

8. It is recommended that trial pieces are tested before commencing actual project.

· Position a test piece of your selected material (paper, card, etc) on top of the make-ready mat

· Place foil shiny side up on top of your test piece.

· Using both hands, hold the handle of the press and bring it down firmly and with some pressure.

· Hold for only a short time and then bring the handle back up with one hand whilst holding the work in place.

9. Gently and slowly peel back the foil revealing your foiled print.

10. The Platen (7) can be modified, using the tool provided, in the adjustment apertures in the well underneath the platen.

11. When you are satisfied with the print, repeat the procedure on your actual project.

For more detail and hints and tips on how to achieve the best print go to www.craftdragon.com.

Using your CraftDragon® ImPress

How to use the CraftDragon® ImPress for Precision Ink Stamping

By replacing the Imp with the Flexi-bloc™ you can open up a whole new world of ink stamping enjoyment. Because of the configuration

of the press and the Flexi-bloc™ you can achieve a smudge free, perfect image and create new artistic effects not previously possible.

To replace the Imp with the Flexi-bloc™

· Switch off and remove plug from the Mains supply

· Holding the locking handles either side of the press

1. push the press down with the handles so that the imp meets the print deck

2. Pull locking handles apart to release the Imp

3. let the press handle return gently to up position

4. remove imp from print deck

5. position Flexi-bloc™ to locate with the lugs on the arms of the press

6. pull down the press handle, matching the lugs to the pillars of the Flexi-bloc™ and click into place

· Apply your chosen ink stamp to the Flexi-bloc™

· Apply ink by dabbing upwards with ink pad or bringing down to ink pad with a light dabbing motion.

· Position your project under the flex-bloc™ and pull the handle of the press down applying firm pressure.

For how to get the best from your press and Flexi-bloc™ combination go to www.craftdragon.com.

Using your CraftDragon® ImPress

How to use the CraftDragon® ImPress for embellishing and hot press printing

With the tri-plate inserted into the channels on the base of the imp, the Impress becomes a hot press to apply hot fix crystals designs, vinyl cut-outs

and transfer prints to an impressive array of materials and objects, including T-shirts, coasters etc.

Select required temperature and leave to heat up

To apply crystal designs

Ÿ If applying crystals or studs to garments, place garment pad on print deck.

Ÿ Press fabric with the warm tri-plate to dry the area before applying embellishments or transfer prints.

Ÿ Remove opaque backing film from design.

Ÿ Place design face up with clear application film, sticky side down onto work.

Ÿ Cover with thermo-sheet.

Ÿ Bring the press down to the work with continuous pressure for approximately 15 seconds.

Ÿ Allow work to cool.

Ÿ Slowly peel back clear application film examining for any unfixed crystals.

Ÿ If any crystals have not stuck re-apply application film re-cover with thermo-sheet and re-press.

Ÿ Use this technique to also embellish greeting cards, scrapbook pages etc.

To apply vinyl cut-out designs to fabrics

Ÿ Position fabric on top of garment pad on print deck.

Ÿ Place design where required on fabric or garment.

Ÿ Cover with thermo-sheet.

Ÿ Bring the press down to the work with continuous pressure for approximately 30 seconds.

Ÿ Allow work to cool.

Ÿ Peel back clear application film.

Ÿ If any area has not stuck, re-cover with thermo-sheet and re-press.

To apply transfer prints

Ÿ Print your image using sublimation inks or buy pre-printed images.

Ÿ Position image face down onto project.

Ÿ Cover with thermo-sheet.

Ÿ Bring the press down to the work with continuous pressure for approximately 60 seconds.

Ÿ Allow work to cool.

Ÿ Peel back transfer paper.

For more information on any of these techniques go to www.craftdragon.com.

Using your CraftDragon® ImPress

DO’S AND DON’TS to achieve the best printing results

Ÿ Use the make-ready mat when hot foil stamping onto paper or card.

Ÿ Ensure that the make-ready mat is completely clean and free from debris as this can effect the resulting print.

Ÿ Work on a solid stable surface.

Ÿ Work in an area with a stable ambient temperature (any fluctuation in room temperature can affect results)

Ÿ Make sure the die is correctly positioned in the channel ie., pushed in as far as possible.

Ÿ Ensure that the die is orientated the correct way up before stamping.

Ÿ Test the die is heated thoroughly by doing a test print before proceeding to final work.

Ÿ Preferably use the centre channel of the Imp to insert a single die.

Ÿ Use a positioning mat (available from www.craftdragon.com) to easily align and hold your work in place.

Ÿ Use substrates that are high quality, preferably smooth, even and flat.

Ÿ The ImPress will print on some textured or ‘dry’ materials, but these should be thoroughly tested before using for actual projects.

Ÿ Test for:

1. Correct temperature - If the temperature is too high or low the final image may be affected.

2. Dwell time - If the dwell time is too long or short the resulting image may be affected.

(If bleeding occurs due to excess heat or dwell time the excess foil may be removed with a finishing brush.)

Ÿ Store dies correctly as follows

1. keep the dies stored in dry conditions to avoid degradation of the metal

2. shim between dies when storing to avoid scratching of the printing surface

3. if any pitting does occur the die surface can be lightly sanded with extremely fine sand paper (or flour paper) although this

may shorten the life of the die.

Ÿ Keep foils on the roll to avoid creasing or tearing as this will affect the resulting print.

Ÿ Store foils in dry conditions.

Ÿ Keep the CraftDragon® ImPress clean by following the relevant section in the instruction manual.

DON’T

Ÿ Bring Press handle too sharply as this can cause bounce and result in a double image or cause damage to the ImPress.

Ÿ Allow the arms of the press to spring back too quickly.

Ÿ Put undue strain on the arms of the press.

Ÿ Use a damaged or dirty make ready mat. If the make ready mat is damaged by inadvertently foiling or ink stamping onto it, further prints

may be affected.

Connection to the mains supply

WARNING: THIS APPLIANCE MUST BE EARTHED.

Mains Plug

This product is fitted with a standard UK mains outlet 3 pin plug complying with BS1363 and is designed to operate from a mains supply of

AC230V - 50HZ

Ÿ Should the fuse in the 13 amp plug require changing a 13 amp BS1362 fuse must be fitted.

Ÿ Always replace the fuse with one of the same rating.

Ÿ Check that the voltage marked on the product corresponds with your supply voltage.

Ÿ If the plug is unsuitable for your mains socket or needs to be replaced, please note the following:

Ÿ DO NOT cut off the mains plug from this equipment. If the plug fitted is not suitable for the power points in your home/office or the cable is

too short to reach a power point, then obtain a proper safety approved extension lead /adaptor or consult with Craft Dragon Limited.

Ÿ Important: The wires in the mains lead must be connected as per the following diagram

Always ensure that the plug cord grip is fastened correctly

Mains lead

• The mains lead should reach from the socket to the base unit without straining the connections.

• Do not let the mains lead hang over the edge of a worktop where a child or pet could reach it.

• Do not let the lead run across an open space e.g. between a low socket and table.

• Do not let the lead run across a cooker or toaster or other hot area which might damage the cable.

Ÿ If the mains lead of this appliance is damaged do not use it. The lead may only be replaced by Craft Dragon Ltd or an agent of the company.

Ÿ With the thermostat control switch and power setting switches in the “OFF” Position; plug the CraftDragon® ImPress into the main power supply.

Note:

Ÿ The plug removed from the mains lead, if severed, must be destroyed, as a plug with bared flexible cord is hazardous if engaged into a live

socket outlet.

Live

(Brown)

Earth

(Green/Yellow)

Neutral

(Blue)

DANGER

Electric

For Customer Services

please call

01782 658333

Opening times:

Monday - Friday

9am - 5pm

Craft Dragon Ltd

Unit 18

Trentham Lakes Technology Park

Trentham

Stoke-on-Trent

Staffordshire

ST4 8JL

e. mail: [email protected]

www.craftdragon.com

Company Number: 06813093

We reserve the right, due to possible changes to design, to alter the instruction manual without prior notice

Craft Dragon ImPress CD-ES 080902 User manual

Brand: Craft Dragon

Model: ImPress CD-ES 080902

Type: User manual

This manual is also suitable for

CD-ES 080902

Download PDF

report

Craft Dragon ImPress CD-ES 080902 User manual

This manual is also suitable for

Craft Dragon ImPress CD-ES 080902 User manual

Other documents