Acer Predator PO9-920 User manual

Type
User manual
Predator PO9-920
User’s Guide
-
2
© 2020. All Rights Reserved.
Desktop Computer Covers:
Tower models
This revision: Oct. 2020 V1.00
Important
This manual contains proprietary information that is protected by
copyright laws. The information contained in this manual is
subject to change without notice. Images provided herein are for
reference only and may contain information or features that do not
apply to your computer. Acer Group shall not be liable for technical
or editorial errors or omissions contained in this manual.
The terms HDMI and HDMI High-Definition Multimedia
Interface, and the HDMI Logo are trademarks or
registered trademarks of HDMI Licensing Administrator,
Inc. in the United States and other countries.
Table of Contents -
3
Table of Contents
1. UPGRADING YOUR COMPUTER .................... 5
Installation precautions
.............................. 5
ESD precautions
.......................................... 5
Required tools
.............................................. 5
Pre-installation instructions
.................... 6
Post-installation instructions
.................. 6
System Upgrade
........................................... 7
Removing the Left side system cover
... 7
Installing the Left side system cover
..... 8
Removing the Right side system cover
9
Installing the Right side system cover
10
System Layout ................................................. 11
Hard drives
.................................................. 12
Removing the 3.5-inch hard drives
..... 12
Installing the 3.5-inch hard drives
....... 14
Memory
........................................................ 16
Memory configuration guidelines
....... 16
Removing a memory module
................ 18
Installing a memory module
.................. 19
Graphic board
............................................. 20
Removing the Graphic board
................ 20
Installing the Graphic board
.................. 23
M.2 SSD module
......................................... 25
Removing the M.2 SSD module
............ 25
Installing the M.2 SSD module
............. 27
ODD drives
................................................... 29
Open ODD door.
....................................... 29
Hard swap HDD
.......................................... 30
Dust filter
..................................................... 33
Removing the Dust filter from Front
Bezel
............................................................. 33
Removing the Dust filter from Power
Cover
............................................................ 34
Removing the Front Bezel
...................... 35
ARGB Control PCB
...................................... 36
About LED Number limit for ARGB
Control PCB ports
..................................... 36
ME Features
................................................ 37
2 PREDATORSENSE ....................................... 39
PredatorSense features
............................ 39
- Upgrading your Computer
4
Upgrading your Computer
In this section, you will find:
Instructions on how to replace a hardware component
Upgrading your Computer -
5
1. UPGRADING YOUR COMPUTER
Installation precautions
Before you install any computer component, we recommend
that you read the following sections. These sections contain
important ESD precautions along with pre-installation and
post-installation instructions.
ESD precautions
Electrostatic discharge (ESD) can damage your processor,
disk drives, expansion boards, and other components.
Always observe the following precautions before you install a
computer component:
1. Do not remove a component from its protective
packaging until you are ready to install it.
2. Wear a wrist grounding strap and attach it to a metal part
of the computer before handling components. If a wrist
strap is not available, maintain contact with the computer
throughout any procedure requiring ESD protection.
Required tools
In performing the component replacement process, you will
need the following tools:
Philips screwdriver
Hex screwdriver
Flat screwdriver
Scissors
Note
The screws for the different components vary in size. During the
disassembly process, group the screws with their corresponding
components to avoid mismatches when putting back the components.
- Upgrading your Computer
6
Pre-installation instructions
Always observe the following before you install any
component:
1. Make sure that the ODD and card reader slot is empty.
2. Turn off the power to the computer and all peripherals.
3. Unplug the power cord from the computer.
4. Unplug the network cable and all connected peripheral
devices from the computer.
5. Place the computer on a flat, steady surface.
6. Open your computer according to the instructions on
removing the left side system cover on page 7 and
removing the right side system cover on page 9.
7. See the following sections for specific instructions on the
component you wish to install.
Post-installation instructions
Observe the following after installing a computer component:
1. See to it that the components are installed according to
the step-by- step instructions in their respective sections.
2. Replace any expansion boards or peripherals that you
removed earlier.
3. Replace the system covers. See Installing the left side
system cover on page 8 and installing the right side
system cover on page 10.
4. Connect the necessary cables.
5.
Turn on your computer.
WARNING: Hot surface. Do not touch.
Upgrading your Computer -
7
System Upgrade
Removing the Left side system cover
1. Before you proceed, make sure that you have turned off
your computer and all peripherals connected to it. Read
the Pre- installation instructions on page 6.
2. Remove the two screws that secure the system cover to
the computer.
3. Slide the cover toward the back of the computer and pull
away from the side of the computer.
4. Set the cover aside for re-installation later.
- Upgrading your Computer
8
Installing the Left side system cover
1. Align the cover to the sides of the computer and slide the
cover toward the front of the computer.
2. Secure the cover with two screws.
3. Observe the Post-installation instructions on page 6.
Upgrading your Computer -
9
Removing the Right side system cover
1. Before you proceed, make sure that you have turned off
your computer and all peripherals connected to it. Read
the Pre- installation instructions on page 6.
2. Remove the two screws that secure the system cover to
the computer.
3. Slide the cover toward the back of the computer and pull
away from the side of the computer.
4. Set the cover aside for re-installation later.
- Upgrading your Computer
10
Installing the Right side system cover
1. Align the cover to the sides of the computer and slide the
cover toward the front of the computer.
2. Secure the cover with two screws.
3. Observe the Post-installation instructions on page 6.
Upgrading your Computer -
11
System Layout
HDD
ARGB
Control PCB
RAM
SSD
M2_2
VGA
ODD
SSD
M2_3
PSU
Wifi
M2_1
RAM
Hard swap
2.5HDD
CPU
- Upgrading your Computer
12
Hard drives
The computer supports installation of one 3.5-inch SATA
hard drives in the internal HDD cage.
Removing the 3.5-inch hard drives
1. Perform Pre-installation instructions on page 6.
2. Disconnect the power and data cables from the hard
drives.
Upgrading your Computer -
13
3. Pull black rack out from HDD cage and take it off.
4. Remove the hard drives from the rack.
- Upgrading your Computer
14
Installing the 3.5-inch hard drives
1. Remove the new hard drive from their packaging.
2. Insert the new hard drive into the black rack.
3. Insert black rack into HDD cage.
Upgrading your Computer -
15
4. Connect the power and data cables to the hard drive.
5. Observe the Post-installation instructions on page 6
- Upgrading your Computer
16
Memory
The computer has four DDR4 U-DIMM slots that support up
to 128 GB maximum system memory.
Memory configuration guidelines
To ensure data integrity, use only Acer-approved DDR4
2666/2933 MHz type memory modules.
Install the X.M.P memory and you would like to enabled
X.M.P function, please manual to change the Extreme
Memory Profile[X.M.P] item from “Disabled” to “Enabled”
in BIOS setup menu.
B1
B2
A1
A2
C2
C1
D2
D1
Channel A/B
Channel C/D
Upgrading your Computer -
17
Memory modules must be installed starting with DIMM1
slot.
Always handle memory modules by its edges.
When installing memory modules, populate the DIMM
slots according to the table below.
DRAM(Memory)
Vendor
Description
Acer P/N
MICRON
Memory MICRON UNB-DIMM DDRIV 3200 8Gb
MTA8ATF1G64AZ-3G2J1 LF+HF 1024*8 Z21C
KN.8GB04.045
MICRON
Memory MICRON UNB-DIMM DDRIV 3200 16GB
MTA16ATF2G64AZ-3G2J1 LF+HF Z21C
KN.16G04.014
Kingston
Memory KINGSTON UNB-DIMM DDRIV 2666 8GB
ACR26D4U9S8ME-8 LF+HF 1024*8
KN.8GB07.043
Kingston
Memory KINGSTON UNB-DIMM DDRIV 2666 8GB
ACR26D4U9S8ME-8X LF+HF black PCB&heatshield, MI-E
KN.8GB07.054
Kingston
ACR36D4U1S8HD-8X DDR4-3200 8GB
Kingston
ACR36D4U1D8HD-16X DDR4-3200 16GB
memory
device
Memory slot
Memory Channel
Check
Total
Memory
size result
B1
B2
A1
A2
C2
C1
D2
D1
Post
Screen
CPU-Z
8 dimm
16GB
V
V
V
V
V
V
V
V
Quad
Quad
128GB
7 dimm
16GB
V
V
V
V
V
V
V
Quad
Quad
112GB
6 dimm
16GB
V
V
V
V
V
V
Quad
Quad
96GB
5 dimm
16GB
V
V
V
V
V
Quad
Quad
80GB
4 dimm
16GB
V
V
V
V
Quad
Quad
64GB
3 dimm
16GB
V
V
V
Triple
Triple
48GB
2 dimm
16GB
V
V
Dual
Dual
32GB
16GB
V
V
Dual
Dual
32GB
1 dimm
16GB
V
Single
Single
16GB
- Upgrading your Computer
18
Removing a memory module
1. Perform Pre-installation instructions on page 6.
2. Press outward the holding clips on both sides of the
DIMM slot outward to release the memory module (1).
3. Gently pull the memory module upward to remove it from
the DIMM slot (2).
4. Repeat steps 2~3 to remove the other memory modules.
2
1
Upgrading your Computer -
19
Installing a memory module
1. Select an empty DIMM slot.
2. Remove the new memory module from its packaging,
handling it by the edges.
3. Align then insert the memory module into the DIMM slot
(1).
4. Insert the memory to the slot until the retaining clips snap
inward (2).
The module is keyed so it can only be inserted in one
direction. If the module does not fit, make sure that the
notch in the module lines up with the tab in the memory
slot.
5. Repeat steps 1~4 to install the other memory modules.
6. Observe the Post-installation instructions on page 6.
Note
DIMM slots on the mainboard must be installed only in certain configurations.
Numbers next to DIMM slots correspond to installation sequence.
Be sure to install the memory module in DIMM1 slot followed by DIMM2 slot.
1
2
2
1
- Upgrading your Computer
20
Graphic board
The computer contains one or two Graphic boards installed in
the PCIe x16 slots. The detail configuration will be differed by
different models.
Removing the Graphic board
1. Perform Pre-installation instructions on page 6.
2. Disconnect the power cables from the Graphic board.
3. Remove the tape and disconnect the bridge from the
Graphic boards.
  • Page 1 1
  • Page 2 2
  • Page 3 3
  • Page 4 4
  • Page 5 5
  • Page 6 6
  • Page 7 7
  • Page 8 8
  • Page 9 9
  • Page 10 10
  • Page 11 11
  • Page 12 12
  • Page 13 13
  • Page 14 14
  • Page 15 15
  • Page 16 16
  • Page 17 17
  • Page 18 18
  • Page 19 19
  • Page 20 20
  • Page 21 21
  • Page 22 22
  • Page 23 23
  • Page 24 24
  • Page 25 25
  • Page 26 26
  • Page 27 27
  • Page 28 28
  • Page 29 29
  • Page 30 30
  • Page 31 31
  • Page 32 32
  • Page 33 33
  • Page 34 34
  • Page 35 35
  • Page 36 36
  • Page 37 37
  • Page 38 38
  • Page 39 39
  • Page 40 40
  • Page 41 41

Acer Predator PO9-920 User manual

Type
User manual

Ask a question and I''ll find the answer in the document

Finding information in a document is now easier with AI