Zinwell PWQ-5101C Quick Installation Manual

  • Hello! I am an AI chatbot trained to assist you with the Zinwell PWQ-5101C Quick Installation Manual. I’ve already reviewed the document and can help you find the information you need or explain it in simple terms. Just ask your questions, and providing more details will help me assist you more effectively!
QUICK INSTALLATION GUIDE
Powerline
Wireless Network
WPS Button
Group Button
LAN Port
Power Button
ON: Ethernet link detected
Reset Button
LEDs LIGHT INDICATOR DEFINITION
Group Button
Reset Button
LAN Port
Press 1~3 secs to
reset to factory default
Power LED
Ethernet Link/
Act LED
PLC LED Power LED
PLC LED
WLAN Link/Act LED
Ethernet Link/Act LED
ON: Linked w/ other PLC device
Green: Wi-Fi is encrypted
Red: Wi-Fi is not encrypted
Press to join an
encrypted Wi-Fi network.
Clone AP Button
Press to duplicate current Wi-Fi network.
Press 1~3 secs to join an
encrypted PLC network.
Press over 10 secs to create
the encrypted PLC network.
Press 1~2 secs to
reset to factory default
BEFORE GETTING STARTED
Do Not plug PLC adapter into “surge protector”.
PLC data transmission might be blocked.
Modem / Router
Make sure that router is connected to the Internet.
Internet
500 Mbps
Powerline Bridge
500 Mbps Powerline
Wireless N Extender
/Default
To switch between WPS and Clone AP,
please login to Advanced Wi-Fi Setting
via web browser.
For Instruction Manual go to http://www.zinwell.com.tw/manual/PWQ-5101C_UM.zip
IB04722799-0
**Make sure router is WPS supported.
Plug the PLC adapter to AC outlet and connect to router
or broadband modem with an Ethernet cable (provided)
Plug the PLC Wi-Fi Extender to AC outlet and place it in
a location you wish to extend Wi-Fi access.
CREATE AN ENCRYPTED PLC NETWORK GROUP
ESTABLISH POWERLINE NETWORK DUPLICATE CURRENT SSID & PASSWORD
WITH ONE BUTTON
Step 1
Step 2
Search Wi-Fi network and connect it with (WPA-PSK)
default password.*
* The default Wi-Fi password appears on the product label.
Step 3
User can easily create an encrypted PLC network with
128-bit encryption for network security and data
protection. Simply press GROUP button on adapters to
set up hassle-free PLC encrypted network. To do so,
please follow below steps!
Modem / Router PC
Modem / Router
Press GROUP button on both adapters over 10 secs
until LED light turns off and on at once to generate new
encrypted PLC network. (PLC LED light will be off)
Step 1
Step 1
GROUP
button
GROUP
button
AB
Press GROUP button of adapter A again for 1~3 sec to
start pairing procedure. (Power LED will start blinking)
Step 2
Step 2
Press GROUP button of adapter B for 1~3 sec to start
pairing procedure. (Power LED will start blinking)
Once Pairing procedure is completed, both of PLC LED
light will be on.
Step 3
TROUBLESHOOTING
Make sure PLC LED is on.
What if Powerline adapters are not connected?
a. Verify that PLC LED adapters are
plugged into a power outlet directly.
b. Press RESET button for 2 seconds to
recover the default settings.
c. Shorten the distance between PLC
adapters.
If not,
Clone AP
Simply press Clone AP button to duplicate your
current Wi-Fi SSID and password.
Press Clone AP button* on the extender
and Wi-Fi LED will start blinking.
Press WPS button on the router** and Powerline
Wi-Fi extender will duplicate current Wi-Fi SSID
and password from the router. The extender will
reboot once procedure is completed.
Smartphone
Tablet SSID: OOO
Password: XXX
SSID: OOO
Password: XXX
button
(Default funtion:WPS)
*Make sure WPS button has been switched
to Clone AP button via web browser.
Please refer to p.13 on manual.
/