Copystar CS-C3232E Operating instructions

Operation Guide

C2525E

C3225E

C3232E

C4035E

Please read the Operation Guide before using this machine. Keep it close to the machine for easy reference.

This Operation Guide is for models C2525E, C3225E, C3232E and C4035E. In this guide,

C2525E refers to the 25/25 ppm (prints per minutes) model, C3225E to the 32/25 ppm model,

C3232E to the 32/32 ppm model and C4035E to the 40/35 ppm model.

NOTE: This Operation Guide contains information that corresponds to using both the inch and

metric versions of these machines.

The inch versions of these machines are shown in the screens in this guide. If you are using the

metric version, use the messages provided for the inch version as reference only. In the body

text, only the inch messages are given if these versions differ only in capitalization. When there

is even a slight difference in the message, we have listed the information for the inch version

followed, in brackets, by the corresponding information for the metric version.

i

Taking Advantage of Advanced Functions

Basic Copying...See Operation Guide Chapter 3

Advanced Copying

Duplex Mode

Create two-sided copies automatically

from any kind of original

Split Mode

Copy double-sided or two-page

originals onto separate sheets

automatically

Offset Mode

Handy option to stack sets in

alternating orientations

Combine Mode

Combine two or four originals on a

single page

Margin Mode

Set up blank margin or gutter space

for your binding needs

Centering Originals

Customize output by centering the

image on the page

Border Erase

Eliminate unnecessary borders on the

original for cleaner output

Poster

Copy an enlarged image onto several

pages

Page Numbering

Print sequential page numbers on the

copies

Cover Mode

Use a distinctive front and/or back

cover

Booklet

Copy pages for stacking and folding

into booklets

5

4

3

2

1

5

3

4

1

2

1

21

2

1

2

3

2

1

3

2

1

3

2

1

3

2

1

E

D

C

B

A

E

-5-

D

-4-

C

-3-

B

-2-

A

-1-

ii

Memo Mode

Add space for notes next to copied

images

Batch Scanning

Copy high-volume originals in a single

copy job

Sharpness Adjust

Adjust the sharpness of image

outlines

Background Exposure Adjust

Adjust the background of color

images

Proof Copy

Copy a test sheet before a

high-volume job

Repeat Copy

Produce more copies as needed after

making the initial copies

OHP Backing Sheet Mode

Insert plain paper backing sheets

when printing transparencies for

projectors

EcoPrint

Use toner more efficiently as

necessary

Inverted Copying

Invert both black and white and color

images

Mirror Copying

Create mirror images of originals

Image Repeat Copy

Tiles a copied sheet with an original

image

Color Balance Adjust

Change the strength of image colors

200

100

1

3

2

1

3

2

1

3

2

1

iii

Convenient document/output management functionality

Hue Adjust

Adjust the color (hue) of images

One Touch Image Adjust

Adjust image quality to match the

image

Color/B&W Selection

Make color and B&W copies in one

operation

Single Color Copy

Make copies in 1 other than black

Programmed Copying

Remember commonly used settings

Job Build

Set cover page, middle pages and for each page set shrink/enlarge

and border erase settings and

copy all pages in single operation

Shared Data Box

Store frequently used documents to reproduce them later as needed

even without the original

Vivid

Dull

Sharp

7

8

5

6

3

4

1

2

5

4

3

21

7

8

5

6

3

4

1

2

iv

Printing Functionality

Synergy Print Box

Store commonly used documents... to make them instantly available later

in combination with other copying jobs

Output Management

Modify and manage the output queue

Duplex Path

Automatic duplex printing

Quick Copy

†

Reprint as many sheets as needed

from the operation panel

† Optional hard disk required for quick copy, job storage, and virtual mailbox

Proof and Hold

††

Bulk print after test print

†† Proof and hold and private print require RAM disk to be configured or optional hard disk

Private Print

††

Delay printing until entry from the

operation panel

Job Storage

†

Enable printing commonly used data

any time from the operation panel

Virtual Mailbox

†

Save print data to a virtual mailbox

1

2

3

4

1

4

3

2

5

3

4

1

2

3

2

1

3

2

1

3

2

1

v

Scanning Functionality

Features for Easier Copying

Full-color Scan

Make high quality scans of even color

documents

Scan to PC

Send scanned images to a computer

as PDF or JPEG files

Send E-mail

Send scanned images as e-mail

Scan to FTP

Upload scanned images to FTP

server directly

TWAIN

Import images using a

TWAIN-compliant application

Database Connection

Send scanned images to a computer

after adding text data

Programmed Scanning

Remember destination and feature

settings

Job Accounting

Use department codes to manage

total copy volume

Language

Choose the language to display

messages

A B C

DeutschEnglish

vi

Full optional equipment lineup... See Optional Equipment on page 4-1

Document Processor Paper Feeder 3000 Sheet Paper Feeder

Document Finisher 3000 Sheet Document Finisher (When equipped with a mailbox and

folding unit)

Job Separator Key Counter Fax Kit

Memory Card (CompactFlash) Hard Disk Additional Memory

Security Kit Network Interface Card Serial Interface

Document Table

vii

Legal and Safety Information

Please read this information before using your machine. This chapter provides information on

the following topics:

• Legal Information...viii

• Regarding Tradenames...ix

• Energy Saving Control Function...x

• Automatic 2-Sided Copy Function...x

• Paper Recycling...x

• Energy Star (ENERGY STAR

®

) Program...x

• Safety Conventions in This Guide...xi

• Caution Labels...xii

• Installation Precautions...xiii

• Precautions for Use...xiv

viii

Legal Information

Notice The information in this guide is subject to change without notification. Additional pages may be

inserted in future editions. The user is asked to excuse any technical inaccuracies or

typographical errors in the present edition.

No responsibility is assumed if accidents occur while the user is following the instructions in this

guide. No responsibility is assumed for defects in the printer’s firmware (contents of its read-only

memory).

This guide, any copyrightable subject matter sold or provided with or in connection with the sale

of the machine, are protected by copyright. All rights are reserved. Copying or other

reproduction of all or part of this guide, any copyrightable subject matter without the prior written

consent of Kyocera Mita Corporation is prohibited. Any copies made of all or part of this guide,

any copyrightable subject must contain the same copyright notice as the material from which the

copying is done.

Legal Restriction On Copying

• It may be prohibited to copy copyrighted material without permission of the copyright owner.

• It is prohibited under any circumstances to copy domestic or foreign currencies.

• Copying other items may be prohibited.

ix

Regarding Tradenames

• PRESCRIBE and ECOSYS are registered trademarks of Kyocera Corporation.

• KPDL is trademark of Kyocera Corporation.

• Windows and Windows Server are registered trademarks of Microsoft Corporation.

• Windows NT is a trademark of Microsoft Corporation.

• PCL and PJL are registered trademarks of Hewlett-Packard Company.

• Adobe, Adobe Acrobat and Adobe Reader are registered trademarks of Adobe Systems

Inc.

• PowerPC is a trademark of International Business Machines Corporation.

• CompactFlash is a trademark of SanDisk Corporation.

All other brand and product names are registered trademarks or trademarks of their respective

companies. The designations ™ and ® will not be used in this Operation Guide.

x

Energy Saving Control Function

The device comes equipped with a Low Power Mode where printer and fax functions remain in a

waiting state but energy consumption is still reduced after a certain amount of time elapses

since the device was last used, as well as a Sleep Mode where printer and fax functions remain

in a waiting state but power consumption is still reduced to a minimum when there is no activity

with the device within a set amount of time.

Low Power Mode

The device automatically enters Low Power Mode when 7 minutes have passed since the

device was last used. The amount of time of no activity that must pass before Low Power Mode

is activated may be lengthened. For more information see Low-Power Mode on page 3-35.

Sleep Mode

The device automatically enters Sleep Mode when 29 minutes (25/25 ppm model) or 44 minutes

(32/25, 32/32 and 40/35 ppm models) have passed since the device was last used. The amount

of time of no activity that must pass before Sleep Mode is activated may be lengthened. For

more information see Sleep Mode on page 3-36.

Automatic 2-Sided Copy Function

The Energy Star Program encourages the use of 2-sided copying which reduces the load on the

environment and this device includes 2-sided copying as a standard function. For example, by

copying two 1-sided originals onto a single sheet of paper as a 2-sided copy, it is possible to

lower the amount of paper used. For more information see Duplex Mode on page 3-11.

Paper Recycling

The Energy Star Program encourages the use of recycled paper which reduces the load on the

environment and this device supports recycled paper. Your sales or service representative can

provide information about recommended paper types.

Energy Star (ENERGY STAR

®

) Program

We have determined as a participating company in the International Energy Star Program that

this product is compliant with the standards laid out in the International Energy Star Program.

xi

Safety Conventions in This Guide

Please read this Operation Guide before using the machine. Keep it close to the machine

for easy reference.

The sections of this guide and parts of the machine marked with symbols are safety warnings

meant to protect the user, other individuals and surrounding objects, and ensure correct and

safe usage of the machine. The symbols and their meanings are indicated below.

Symbols

The symbol indicates that the related section includes safety warnings. Specific points of

attention are indicated inside the symbol.

The symbol indicates that the related section includes information on prohibited actions.

Specifics of the prohibited action are indicated inside the symbol.

The  symbol indicates that the related section includes information on actions which must be

performed. Specifics of the required action are indicated inside the symbol.

Please contact your service representative to order a replacement if the safety warnings in this

Operation Guide are illegible or if the guide itself is missing. (fee required)

Note

An original which resembles a bank note closely may not be copied properly in some rare cases

because this machine is equipped with a counterfeiting prevention function.

WARNING: Indicates that serious injury or even death may result from

insufficient attention to or incorrect compliance with the related points.

CAUTION: Indicates that personal injury or mechanical damage may result from

insufficient attention to or incorrect compliance with the related points.

.... [General warning]

.... [Warning of danger of electrical shock]

.... [Warning of high temperature]

.... [Warning of prohibited action]

.... [Disassembly prohibited]

.... [Alert of required action]

.... [Remove the power plug from the outlet]

.... [Always connect the machine to an outlet with a ground connection]

xii

Caution Labels

Caution labels have been attached to the machine at the following locations for safety purposes.

Be sufficiently careful to avoid fire or electric shock when removing a paper jam or when

replacing toner.

NOTE: Do not remove these labels.

Label 1, 2

High temperature inside. Do not

touch parts in this area,

because there is a danger of

getting burned.

xiii

Installation Precautions

Environment

Caution

Avoid placing the machine on or in locations which are unstable or not level. Such

locations may cause the machine to fall down or fall over. This type of situation presents

a danger of personal injury or damage to the machine.

Avoid locations with humidity or dust and dirt. If dust or dirt become attached to the

power plug, clean the plug to avoid the danger of fire or electrical shock.

Avoid locations near radiators, heaters, or other heat sources, or locations near

flammable items, to avoid the danger of fire.

To keep the machine cool and facilitate changing of parts and maintenance, allow access

space as shown below. Leave adequate space, especially around the rear cover, to allow

air to be properly ventilated out of the machine.

Other precautions

The service environmental conditions are as follows:

• Temperature: 50 to 90.5 °F (10 to 32.5 °C), but humidity should be 70 % or less when

temperature is 90.5 °F (32.5 °C)

• Humidity: 15 to 80 %, but temperature should be 86 °F or less (30 °C or less) when humidity

is 80%

However, adverse environmental conditions may affect the image quality. It is recommended to

use the machine at a temperature: around 60.8 to 80.6 °F (16 to 27 °C), humidity: around 36 to

65 %. In addition, avoid the following locations when selecting a site for the machine.

• Avoid locations near a window or with exposure to direct sunlight.

• Avoid locations with vibrations.

• Avoid locations with drastic temperature fluctuations.

• Avoid locations with direct exposure to hot or cold air.

• Avoid poorly ventilated locations.

19 11/16"

50 cm

11 13/16"

30 cm

39 3/8"

100 cm

3 15/16"

10 cm

xiv

Small amounts of ozone and other chemicals are released during copying, but the quantities do

not present any health risk to humans. If, however, the machine is used over a long period of

time in a poorly ventilated room or when making an extremely large number of copies, the smell

may become unpleasant. To maintain the appropriate environment for copy work, it is suggested

that the room be properly ventilated.

Do not install this machine beneath fluorescent lights. The original size may be detected

incorrectly.

Power supply/Grounding the machine

Warning

Do not use a power supply with a voltage other than that specified. Avoid multiple

connections in the same outlet. These types of situations present a danger of fire or

electrical shock.

Plug the power cord securely into the outlet. If metallic objects come in contact with the

prongs on the plug, it may cause a fire or electric shock.

Always connect the machine to an outlet with a ground connection to avoid the danger of

fire or electrical shock in case of an electric short. If an earth connection is not possible,

contact your service representative.

Other precautions

Connect the power plug to the closest outlet possible to the machine.

Handling of plastic bags

Warning

Keep the plastic bags that are used with the machine away from children. The plastic

may cling to their nose and mouth causing suffocation.

Precautions for Use

Cautions when using the machine

Warning

Do not place metallic objects or containers with water (flower vases, flower pots, cups,

etc.) on or near the machine. This of situation presents a danger of fire or electrical shock

should they fall inside.

Do not remove any of the covers from the machine as there is a danger of electrical

shock from high voltage parts inside the machine.

Do not damage, break or attempt to repair the power cord. Do not place heavy objects on

the cord, pull it, bend it unnecessarily or cause any other type of damage. These types of

situations present a danger of fire or electrical shock.

Never attempt to repair or disassemble the machine or its parts as there is a danger of

fire, electrical shock or damage to the laser. If the laser beam escapes, there is a danger

of it causing blindness.

If the machine becomes excessively hot, smoke appears from the machine, there is an

odd smell, or any other abnormal situation occurs, there is a danger of fire or electrical

shock. Turn the main power switch off ( position) immediately, be absolutely certain to

remove the power plug from the outlet and then contact your service representative.

xv

If anything harmful (paper clips, water, other fluids, etc.) falls into the machine, turn the

main power switch off ( position) immediately. Next, be absolutely certain to remove the

power plug from the outlet to avoid the danger of fire or electrical shock. Then contact

your service representative.

Do not remove or connect the power plug with wet hands, as there is a danger of

electrical shock.

Always contact your service representative for maintenance or repair of internal parts.

Caution

Do not pull the power cord when removing it from the outlet. If the power cord is pulled,

the wires may become broken and there is a danger of fire or electrical shock. (Always

grasp the power plug when removing the power cord from the outlet.)

Always remove the power plug from the outlet when moving the machine. If the power

cord is damaged, there is a danger of fire or electrical shock.

Always hold the designated parts only when lifting or moving the machine.

For safety purposes, always remove the power plug from the outlet when performing

cleaning operations.

If dust accumulates within the machine, there is a danger of fire or other trouble. It is

therefore recommended that you consult with your service representative in regard to

cleaning of internal parts. This is particularly effective if accomplished prior to seasons of

high humidity. Consult with your service representative in regard to the cost of cleaning the

internal parts of the machine.

Other precautions

If the optional fax kit is installed, when the main power switch is off ( position), fax send/receive

is disabled. To turn the power off, press the Power key on the operation panel.

Do not place heavy objects on the machine or cause other damage to the machine.

Do not open the front cover, turn off the main power switch, or pull out the power plug during

copying.

When lifting or moving the machine, contact your service representative.

Do not touch electrical parts, such as connectors or printed circuit boards. They could be

damaged by static electricity.

Do not attempt to perform any operations not explained in this handbook.

Caution: Use of controls or adjustments or performance of procedures other than those

specified herein may result in hazardous radiation exposure.

Do not look directly at the light from the scanning lamp as it may cause your eyes to feel tired or

painful.

This machine comes equipped with an HDD (hard disk). Do not attempt to move the machine

while the power is still on; Since any resulting shock or vibration may cause damage to the hard

disk, be sure to turn off the power before attempting to move the machine.

Other precautions (for users in California, the United States)

This product contains a CR Coin Lithium Battery which contains Perchlorate Material - special

handling may apply. See www.dtsc.ca.gov/hazardouswaste/perchlorate

.

xvi

Cautions when handling consumables

Caution

Do not attempt to incinerate the toner container or the waste toner box. Dangerous

sparks may cause burns.

Keep the toner container and the waste toner box out of the reach of children.

If toner happens to spill from the toner container or the waste toner box, avoid inhalation

and ingestion, as well as contact with your eyes and skin.

• If you do happen to inhale toner, move to a place with fresh air and gargle thoroughly

with a large amount of water. If coughing develops, contact a physician.

• If you do happen to ingest toner, rinse your mouth out with water and drink 1 or 2 cups of

water to dilute the contents of your stomach. If necessary, contact a physician.

• If you do happen to get toner in your eyes, flush them thoroughly with water. If there is any

remaining tenderness, contact a physician.

• If toner does happen to get on your skin, wash with soap and water.

Do not attempt to force open or destroy the toner container or the waste toner box.

Other precautions

After use, always dispose of the toner container and the waste toner box in accordance with

Federal, State and Local rules and regulations.

If the machine will not be used for an extended period of time, remove the paper from the

cassette and the MP tray (multi-purpose tray), return it to its original package and reseal it.

Don’t store the unit in a place exposed to:

• Direct sunlight

• High or rapidly variable temperature or humidity (limit: 104 °F or 40 °C)

xvii

Laser Safety (Europe)

Laser radiation could be hazardous to the human body. For this reason, laser radiation emitted

inside this machine is hermetically sealed within the protective housing and external cover. In

the normal operation of the product by user, no radiation can leak from the machine.

This machine is classified as Class 1 laser product under IEC 60825.

Caution: Performance of procedures other than those specified in this manual may result in

hazardous radiation exposure.

These labels are attached to the laser scanner unit inside the machine and are not in a user

access area.

The label shown below is attached on the right side of the machine.

xviii

Safety Instructions Regarding the Disconnection of Power

Caution: The power plug is the main isolation device! Other switches on the equipment are only

functional switches and are not suitable for isolating the equipment from the power source.

VORSICHT: Der Netzstecker ist die Hauptisoliervorrichtung! Die anderen Schalter auf dem

Gerät sind nur Funktionsschalter und können nicht verwendet werden, um den Stromfluß im

Gerät zu unterbrechen.

DECLARATION OF CONFORMITY

TO

89/336/EEC, 73/23/EEC, 93/68/EEC and 1995/5/EC

Radio Frequency Transmitter

This machine contains the transmitter module. We, the manufacturer hereby declare that this

equipment is in compliance with the essential requirements and other relevant provisions of

Directive 1999/5/EC.

Radio Tag Technology

In some countries the radio tag technology used in this equipment to identify the toner container

may be subject to authorization and the use of this equipment may consequently be restricted.

We declare under our sole responsibility that the product to which this

declaration relates is in conformity with the following specifications.

EN55024

EN55022 Class B

EN61000-3-2

EN61000-3-3

EN60950

EN60825-1

EN300330-1

EN300330-2

Page is loading ...

Copystar CS-C3232E Operating instructions

Related papers

Other documents