Bright Clean 20752-000 User manual

Brand: Bright Clean

Model: 20752-000

Type: User manual

IMPORTANT SAFETY INSTRUCTIONS

Read and Save:

1. Fixture can be used with an approved triac dimmer switch. Dimmable to 10% with recommended dimmers:

LUTRON-DVCL-153PR-WH.

2. Do not link together more than six units of fixtures on any single run.

3. To reduce the risk of death, personal injury or property damage from fire, electric shock, falling parts, cuts/abrasions,

and other hazards read all warnings, instructions, and fixture labels.

4. Before installing, servicing, or performing routine maintenance upon this equipment, follow these general precautions.

5. Commercial installation, service and maintenance of luminaires should be performed by a qualified licensed electrician.

6. For Residential installation: If you are unsure about the installation or maintenance of the luminaire, consult a qualified

licensed electrician and check your local electrical code.

7. DO NOT INSTALL DAMAGED PRODUCT!

8. SUITABLE FOR OPERATION IN AMBIENT TEMPERATURES NOT EXCEEDING 40°C.

9. These instructions do not purport to cover all details or variations in equipment nor provide every possible contingency

in connection with installation, operation, or maintenance.

10. Suitable for damp locations. For indoor use only.

11. Do not make or alter any open holes in an enclosure of wiring or electrical components during installation.

LIGHT BULB REPLACEMENT

WARRANTY

2. Turn off the unit and allow the bulb to cool before touching.

CLEANING AND MAINTENANCE

1. Clean using a mild cleaning solution and a soft cloth.

2. Never use a rough cloth or chemical cleaners containing acids, abrasives or solvents.

Model No.:20752-000, 20753-000, 20754-000, 20755-000

LED ANTIBACTERIAL UNDER CABINET

For Customer Assistance:

www.evolutionlightingllc.com

Made In China

1. Integrated LED bulb replacement not required.

3 YEAR LIMITED WARRANTY. Based on 3 hours of daily use.

SAFETY INFORMATION

For Customer Assistance:

www.evolutionlightingllc.com

Made In China

Please read and understand the entire manual before attempting to assemble, operate or

install the product.

WARNING

WARNING: RISK OF ELECTRICAL SHOCK

•

• Turn off electrical power at fuse or circuit breaker box before wiring fixture to the power supply.

• Turn off the power when you perform any maintenance.

• Verify that supply voltage is correct by comparing it with the luminaire label information.

• Make all electrical and grounded connections in accordance with the National Electrical Code and

any applicable local code requirements.

• All wiring connections should be capped with UL approved wire connectors.

• Account for small parts and destroy packing material, as these may be hazardous to children.

•

ELECTRICAL CONNECTIONS (Required Supply Circuit: 120Vac, 60Hz)

CAUTION: RISK OF INJURY

• Allow fixture to cool before handling. Do not touch enclosure or light source.

• Do not exceed maximum wattage marked on luminaire label.

• Do not use 5’ power cord accessory when also direct-wiring the fixture! Use only one method to

power the fixture.

WARNING: RISK OF BURN

• Keep combustible and other materials that can burn away from luminaire and lamp/lens.

• Minimum 90° C supply conductors.

CAUTION: RISK OF FIRE

• This equipment has been tested and found to comply with the limits for a Class B digital device,

pursuant to part 15 of the FCC Rules. These limits are designed to provide reasonable protection

against harmful interference in a residential installation. This equipment generates, uses and can

radiate radio frequency energy and, if not installed and used in accordance with the instructions,

may cause harmful interference to radio communications. However, there is no guarantee that

interference will not occur in a particular installation. If this equipment does cause harmful

interference to radio or television reception, which can be determined by turning the equipment

off and on, the user is encouraged to try to correct the interference by one or more of the following

measures:

< Reorient or relocate the receiving antenna.

< Increase the separation between the lighting unit and receiver.

< Connect the lighting unit into an outlet on a circuit other than the outlet which the receiver is

connected.

< Consult the dealer or an experienced radio/TV technician for help.

NOTE: Please note that changes and modifcations not expressly approved by the party responsible

for compliance could void the user's authority to operate the equipment.

INSTALLATION (POWER-CORD METHOD)

For Customer Assistance:

www.evolutionlightingllc.com

Made In China

1. Remove fixture from the carton and check for any shipping

damage. Note: TURN OFF POWER AT CIRCUIT BREAKER BOX!

WIRING AND FIXTURE OPERATION CAUTION: Connect fixture

to supply wires rated for at least 90°C (194°F). Assistance may be

required to support fixture during installation.

2. Determine location of your first fixture. Make sure the mounting

location is within 5 feet of an electrical outlet.

3. Position the fixture housing against the mounting surface and

with a pencil, mark the screw hole locations to be located at the

narrow section of the keyholes (See Fig.1).

Fig.3

Fig.1

10. Plug in 5’ power cord to a grounded three-prong electrical

outlet (See Fig.5).

11. When all fixtures have been properly installed, ensure all of the

fixtures in the chain have been securely connected.

Part

Description

Qty

Direct-Wire Cavity Access Plate Screw

Direct-Wire Cavity Access Plate

Wire Terminals

Wire

Fixture Assembly

End-to-End Port Cover

Mounting Screws

End-to-End Row connector

Romex Bushing

13’’ Connector Cord

5’Power Cord

WARNING: RISK OF ELECTRICAL SHOCK

• Do not use 5’ power cord accessory when also direct-

wiring the fixture! Use only one method to power the fixture.

9. After installation completed, place the End-to-End Port Cover

on the output port (See Fig.4).

12. Turn on power at the circuit breaker box and verify that fixture

functions properly. If fixture does not turn on, verify that the rocker

switch on each fixture is in the “on” position.

Fig.5

4. Using a drill with a 1/8" drill bit (not included), make two small

pilot holes at the marked locations. (Note: do not drill entirely

through mounting surface).

5. Partially install the provided mounting screws with a Phillips

screwdriver (not included).

6. Position the keyhole mounting holes over the screw heads and

slide the fixture until the screw heads are over the narrow section

of the keyholes. Finish tightening the screws to secure the fixture.

7. If using only one fixture skip to Step 9.

8. If connecting more fixtures, please repeat steps 3-6.

WARNING: Do not link together more than six units of fixtures on

any single run.

Note: The distance between fixtures cannot exceed the length of

the included 13" connector cord (See Fig.2) or end-to-end row

connector (See Fig.3).

To route your fixtures around a corner, simply install a fixture near

the corner and route the 13” connector cord around the corner

to connect the next fixture.

Fig.2

Fig.4

Fig.6

Fig.7

Fig.8

For Customer Assistance:

www.evolutionlightingllc.com

Made In China

1. Loosen the screw with a Phillips screw driver (not included).

(See Fig.6).

4. Loosen the screws and take down the backboard (See Fig.10).

5. Pull the wires with the wire terminals and connect with the input

cord from the conduit (see Fig.11). Insert the white supply wire

(neutral) into wire terminals with the preassembled white fixture

wire.Insert the black supply wire (hot) into wire terminals with the

preassembled black fixture wire. Insert supply ground wire into wire

terminals with the preassembled fixture ground wire.

12. Turn on power at the circuit breaker box and verify that fixture

functions properly. If fixture does not turn on, verify that the rocker

switch on each fixture is in the “on” position.

NOTEWhen install the hex nut, make sure the small step (A

side) facing the Cavity Access Plate , and the D part is parallel

with the plate, not vertical (see Fig.8). After the hex nut is

tightened, make sure its B side is parallel with the plate’s C side

(see Fig.9).

2. Remove Direct-Wire Cavity Access Plate . Determine

appropriate knockout for removal in relationship to incoming

Romex (power supply).

TO REMOVE KNOCKOUTS:

Place a standard screwdriver (not included) on edge of circle (on

opposite side from retaining tabs) and gently strike with hammer.

Grip edge with pliers and flex back and forth until removed (See

Fig. 7).

3. Push supply cable through the Romex Bushing . Strip black

and white wire leads with wire strippers to expose 3/8"-7/16" of

bare metal (See Fig.8). If wiring is being routed through the

knockout on the Direct-Wire Cavity Access Plate , install

Romex Bushing into the access plate (See Fig.8). Insert and

secure the supply cable by tighten the screws on Romex Bushing.

(See Fig.8). Secure the Direct-Wire Cavity Access Plate onto

the fixture assembly.

INSTALLATION (DIRECT-WIRE METHOD - CONVERTIBLE)

WARNING: RISK OF ELECTRICAL SHOCK

• Do not use 5’ power cord accessory when also direct-wiring

the fixture! Use only one method to power the fixture.

6. Put the wires in order inside of the under cabinet, put on

backboard and screw up (See Fig.12).

7. Position the fixture housing against the mounting surface and

with a pencil, mark the screw hole locations to be located at the

narrow section of the keyholes (See Fig.1).

Fig.11

11. If using only one fixture skip to Step 12. If connecting more

fixtures, please follow steps 7-10. WARNING: Do not link

together more than six units of fixtures on any single run.

Note: The distance between fixtures cannot exceed the length of

the included 13" connector cord (See Fig.2) or end-to-end row

connector (See Fig.3).

To route your fixtures around a corner, simply install a fixture near

the corner and route the 13” connector cord around the corner

to connect the next fixture.

Fig.10

Fig.1

Fig.2

Fig.3

8. Using a drill with a 1/8" drill bit (not included), make two small

pilot holes at the marked locations. (Note: do not drill entirely

through mounting surface).

9. Partially install the provided mounting screws with a Phillips

screwdriver (not included).

10. Position the keyhole mounting holes over the screw heads and

slide the fixture until the screw heads are over the narrow section

of the keyholes. Finish tightening the screws to secure the fixture.

Fig.12

Fig.9

This product has been proven to reduce bacteria using key wavelengths that affect bacteria cells biologically. This product does NOT

emit ultra-violet light (UV). This product is NOT harmful to humans, animals, or plants.

To maximize the antibacterial effect, this product should be left on for several hours each day at full power. The longer the light is on,

the more effective it will be in reducing bacteria. This product is dimmable, but for maximum antibacterial effect, please use at full

power when operating to eliminate bacteria.

The product is intended for use in a kitchen setting, installed underneath cabinet shelves and above counter tops. The counter tops

are the target surface for eliminating bacteria. For best results, counter tops should be within 18 inches of the installed light fixture.

The fixture should be located centered over the counter to maximize direct light contact. This product will only impact bacteria that the

light directly reaches. Objects blocking the light or casting shadows will not allow for strong disinfection of the target surface.

This product is not intended to eliminate other forms of cleaning. When used in conjunction with good cleaning practices, this product

will more effectively reduce and eliminate bacteria.

This product is not for disinfecting food or liquids.

Staphylococcus aureus (incl. MRSA)

For Customer Assistance:

www.evolutionlightingllc.com

Made In China

APPLICATION GUIDE

What germs is Ellumi Effective Against?

Bacteria

Bacterial Endospores

Gram Positive•

Bacillus cereus

Clostridium difficile

Yeast and Filamentous Fungi

Aspergillus niger

Candida albicans

Saccharomyces cerevisiae

Clostridium perfringens

Clostridium difficile

Enterococcus faecalis

Staphylococcus epidermidis

Staphyloccocus hyicus

Streptococcus pyogenes

Listeria monocytogenes

Bacillus cereus

Mycobacterium terrae

Lactococcus lactis

Lactobacillus plantarum

Bacillus circulans

Streptococcus thermophilus

Acinetobacter baumannii

Gram Negative•

Pseudomonas aeruginosa

Klebsiella pneumoniae

Proteus vulgaris

Escherichia coli

Salmonella enteritidis

Shigella sonnei

Serratia spp.

Salmonella typhimurium

Page is loading ...

Consumer Service

Service d’aide aux Consommateurs

Servicio al Consumidor

http://www.evolutionlightingllc.com

LIMITED WARRANTY

EVOLUTION LIGHTING warrants all of its lighting fixtures against defects in materials and workmanship for one (1) year from the date of

original purchase. Electronic parts including passive infrared devices, photoelectric switching mechanisms, and light bulbs provided with

Evolution Lighting products are warranted for 30 days from the date of original purchase.

ENERGY STAR qualified product, which include GU24 Energy Star qualified bulbs, are warranted for repair or replacement of defective

parts of the luminaire

housing, mounting hardware, optics, ballast and trim for three (3) years from the date of purchase. GU24 based

integrated lamps included with the luminaire, carry a three (3) year warranty.

ENERGY STAR qualified Solid State product with replaceable components warrants the replaceable components for three (3) years.

ENERGY STAR qualified Solid State product with non replaceable components is warranted for five (5) years.

This warranty does not cover parts becoming defective due to misuse, accidental damage, improper handling and/o

r installation and

specifically excludes liability for indirect, incidental or consequential damages. Product found to be defective may or may not be replaced

with same or like type product, contingent on the nature of the defect, and or replacement availability and or compensated for at a pro

rated value. This warranty gives you specific rights and you may also have other rights, which vary from state to state. Proof of purchase is

required to exercise the warranty

GARANTÍA LIMITADA

EVOLUTION LIGHTING garantiza todas sus luminarias contra defectos de material y mano de obra por (1) año a contar de la fecha

original de compra. Las piezas electrónicas, lo que incluye dispositivos infrarrojos pasivos, mecanismos de conmutación fotoeléctrica, y

bombillas que vengan incluidas con el producto Evolution Lighting, están garantizadas por 30 días a contar de la fecha original de compra.

Los productos calificados por ENERGY STAR, lo que incluye bombillas GU24 calificadas por Energy Star, están garantizados por tres (3)

años a contar de la fecha de compra y s

erán repara dos o cambiados si la caja de la luminaria, el equipo de montaje, la óptica, el

balastro o las molduras tienen piezas defectuosas. Las bombillas integradas con base GU24 que vienen con la luminaria, están

garantizadas por tres (3) años.

Los repuestos para productos en estado sólido calificados por ENERGY STAR están garantizados por tres (3) años.

Los productos en estado sólido calificados por ENERGY STAR que no contengan repuestos están garantizados por cinco (5) años.

Esta garantía no cub

re las piezas que tengan defectos debidos a su mal uso, a daños accidentales, y al manejo y/o la instalación

inapropiada de las mismas, y libera específicamente de toda responsabilidad por daños indirectos, casuales o consiguientes. Un

producto considerado defectuoso puede o no ser cambiado por otro producto idéntico o similar, dependiendo del tipo de defecto y/o a la

disponibilidad de un producto por el cual cambiarlo, y/o puede ser compensado a un valor prorrateado. Esta garantía le da derechos

específicos además de los cuales puede tener otros, los cuales varían entre estados. S

e requiere un comprobante de compra para

cobrar la garantía.

GARANTIE LIMITÉE

EVOLUTION LIGHTING garantit tous ses luminaires de tout défaut en termes de matériel et de main-d’œuvre pendant un (1) an à

compter de la date d’achat d’origine. Les composants électroniques, incluant les éléments infrarouges passifs, les mécanismes

d’interrupteur photoélectriques et les ampoules fournies par les produits Evolution Lighting sont garantis 30 jours à compter de la date

d’achat d’origine.

Les produits homologués ENERGY STAR, incluant les ampoules GU24 homologuées Energy

Star, sont garantis pendant trois (3) ans à

compter de la date d'achat et seront réparés ou remplacés si le corps du luminaire, les pièces de montage, l'optique, le contrepoids et

la bordure sont défectueux. Les lampes intégrées à culot GU24, qui viennent avec le luminaire, sont garanties pendant trois (3) ans.

Les produits à état solide homologués ENERGY STAR qui ont des composants remplaçables, ont leurs composants remplaçables

garantis pendant trois (3) ans.

Les produits à état solide homologués ENER

GY STAR qui ont des composants non remplaçables sont garantis pendant cinq (5) ans.

Cette garantie ne couvre pas les pièces qui deviennent défectueuses en raison d’une mauvaise utilisation ou manipulation, d’un accident

et/ou d’une installation incorrecte. Elle exclut spécifiquement tout risque d’endommagement consécutif ou indirect. Un produit découvert

défectueux sera ou non remplacé par un produit identique ou similaire, selon la nature du défaut et/ou la disponibilité du remplacement,

et/ou sera compensé à une valeur au pro rata. Cette garantie vous donne des droits spécif

iques, et vous pouvez également avoir

d’autres droits, qui varient selon les états. La preuve d’achat est exigée pour exercer le droit à la garantie.

Bright Clean 20752-000 User manual

Brand: Bright Clean

Model: 20752-000

Type: User manual

Download PDF

report

in other languages

français: Bright Clean 20752-000 Manuel utilisateur
español: Bright Clean 20752-000 Manual de usuario

Bright Clean 20752-000 User manual

Bright Clean 20752-000 User manual

in other languages

Other documents