Riva RC6602HD-5311 Installation guide
- Category
- Security cameras
- Type
- Installation guide
2
www.rivatech.de
INFORMATION TO USER
CAUTION
RISK OF ELECTRIC SHOCK,
DO NOT OPEN
CAUTION: TO REDUCE THE RISK OF ELECTRIC SHOCK,
DO NOT REMOVE COVER (OR BACK).
NO USER SERVICEABLE PARTS INSIDE.
REFER SERVICING TO QUALIFIED SEERIVCE PERSONEL.
This symbol is intended to alert the user to the presence of un-
insulated “dangerous voltage” within the product’s enclosure that
may be of sufficient magnitude to constitute a risk of electric
shock to persons.
This symbol is intended to alert the user to the presence of
important operating and maintenance (servicing) instructions in
the literature accompanying the appliance.
!
!
3
RC Series RC6602HD-5311
Installation Guide
www.rivatech.de
Table of Contents
1. FEATURES .............................................................................. 4
2. PACKAGE CONTENTS ................................................................ 7
3. PART NAMES .......................................................................... 7
4. INSTALLATION ......................................................................... 9
4.1. Installation Template .................................................................... 10
4.2. Adjusting LED options and lens focus .............................................. 11
4.3. Setting the Image Attribute ........................................................... 12
5. CABLE CONNECTIONS ........................................................... 122
6. CONFIGURATION .................................................................. 155
6.1.Set up network environment ........................................................ 155
6.1.1. Generic IP Environment ........................................................ 155
6.1.2. Custom IP Environment ........................................................ 166
6.2. View video on web page ............................................................. 177
6.2.1. View video using IPAdmin Tool ............................................... 199
6.3. Reset ........................................................................................ 20
6.4. Factory Default ........................................................................... 20
APPENDIX (A): SPECIFICATIONS .................................................... 21
Summary .......................................................................................... 21
Electrical Characteristics ..................................................................... 22
Environment Condition ........................................................................ 22
Mechanical Condition .......................................................................... 23
APPENDIX (B): DIMENSIONS ........................................................ 23
APPENDIX (C): HEXADECIMAL-DECIMAL CONVERSION TABLE ............. 24
REVISION HISTORY ..................................................................... 25
4
RC Series RC6602HD-5311
Installation Guide
www.rivatech.de
1. FEATURES
Camera
Full HD Indoor/Outdoor IR Bullet IP Camera
1/2.7” High Quality CMOS Image Sensor
True Day / Night (ICR)
Improvement of color rolling suppression
Remote Zoom/Focus Control(One Click AF)
Streaming
Dual streaming mode (such as different codec/resolution/bit rate and so
on.)*
Burnt-in text supported
Unicast/Multicast supported
Video/Audio
Video compression: H.264/MJPEG, up to 30FPS@1080p*
Analog video output (for installation only)
Audio compression: G.711(µLaw, aLaw)/PCM
Two-way mono audio supported
Video Motion Detection supported
Network
RTSP/ HTTP protocol supported
10/100 Base-T Ethernet
5
RC Series RC6602HD-5311
Installation Guide
www.rivatech.de
Additional Features
OSD for camera control supported
Micro SD card supported
SDK (Software Development Kit) provided
VCA detect (Included as basic)
Integrated infrared LED’s
Fan/Heater unit (heater function only with external power supply)
* When VCA is activated, frame rate is limit to max15fps@1080p. Limitations are
based on V.1.5.0 firmware release and could be changed without notice.
Please note:
When using integrated LED illumination as major light source during night time,
unwanted VCA alarm events through flying insect’s activity are possible.
6
RC Series RC6602HD-5311
Installation Guide
www.rivatech.de
2. PACKAGE CONTENTS
Unpack carefully and handle the equipment with care. The packaging contains:
Camera
Video out cable
Hex wrench driver
Screws
Quick installation Guide
DC power adaptor
Screw anchors
Terminal block
The above contents are subject to change without prior notice.
Note
i
7
RC Series RC6602HD-5311
Installation Guide
www.rivatech.de
2. PART NAMES
1 Sunshield
Position the sunshield to prevent direct sunshine.
2 Control panel
Open the control panel to control LEDs, OSD menus, and the extra video output. You
can also find the reset button on the control panel. To learn how to reset your device,
refer to
6.3. Reset
.
3 Ventilation hole
The ventilation holes help to reduce the temperature difference between inside and
outside and prevent water from being condensate.
IPN6602HD-5311
IPN6602HD-5215
TELE
WIDE NEAR
FAR AF
NT/PAL
F/D
VOUT
VOUT
F/D
NT/PAL
TELE WIDE
FAR NEAR
IPN6602HD-5215
DCBA
A : DO-
B : DO+
C : DI+
D : DI-
Red : AIN
White : AOUT
Cable arrange
* Models herein and their
appearance are subject to
change without any prior
notice.
①
①
④
⑦
⑥
⑤
②
⑧
⑨
⑩
③
⑪
8
RC Series RC6602HD-5311
Installation Guide
www.rivatech.de
4 Joint for 3 axis
Use this part to adjust the camera to the desired position. Refer to
4. Installation
for
more details.
5 Panning joint
Use this part for panning adjustment. Refer to
4. Installation
for more details.
6 Tilting adjustment
Use this part for tilting adjustment. Refer to
4. Installation
for more details.
7 4 Pin Connector
A: DO,- B: DO+, C: DI+, D: DI-
8 Power Adaptor Connector
The camera needs DC 12V for power supply.
9 Network Port
Use this RJ45 LAN connector for connecting the camera to network.
10 Audio In
Connect to the audio input device such as a mike.
11 Audio Out
Connect to the audio output device such as the amplifier speaker.
9
RC Series RC6602HD-5311
Installation Guide
www.rivatech.de
3. INSTALLATION
The camera may fall off the ceiling even after the proper installation
and mounting. To prevent any accident, make sure the ceiling is
firm and stable enough to support the camera. If any reinforcement
is needed, consult with your safety personnel and proceed with the
installation.
Caution
!
1) Place the installation template that is provided in the package
on the desired position of installation.
2) Drill four holes on the template and insert anchor blocks into
the holes. Fasten the camera with screws.
3) Make sure the cables are properly connected to the camera.
4) Adjust the camera to the desired angle by unscrew the joints by
referring to the following pictures.
Adjust this joint
to install it on
the wall
Tiling adjustment
Panning
adjustment
11
RC Series RC6602HD-5311
Installation Guide
www.rivatech.de
3.2. Adjusting LED options and lens focus
Adjust the zoom and focus of the lens with push-buttons shown on follow description.
TELE/WIDE: Uses to setup right zoom lens position
FAR/NEAR: Uses to setup right image focus
AF: Push button to start the one time auto focus function
NTSC/PAL: Can be used to change video output as PAL or NTSC. The default is no
video output, but whenever you push the button the video output is changed and
repeated as follow:
No video output -> NTSC -> PAL.
Please note that the analog video
signal is only 3 minutes present and go back automatically to none video output mode
(only installation process)
Vout: Connect a monitor for analog video output to check the camera connection and
its focus at the installation site. To see the video, make sure to set the output
configuration push button to NTSC or PAL according to the video standard. Video out
can be used only for installation and works for 3 minutes after PAL/NTSC button is
pushed.
IPN6602HD-5311
IPN6602HD-5215
TELE
WIDE NEAR
FAR AF
NT/PAL
F/D
VOUT
VOUT
F/D
NT/PAL
TELE WIDE
FAR NEAR
IPN6602HD-5311
IPN6602HD-5215
TELE
WIDE NEAR
FAR AF
NT/PAL
RESET
VOUT
VOUT
NT/PAL
TELE WIDE
FAR NEAR
RESET
12
RC Series RC6602HD-5311
Installation Guide
www.rivatech.de
3.3. Setting the Image Attribute
You can set the image attribute of camera through the webpage.
The menu of image attribute can be seen under Setup > Video & Audio > Camera.
Brightness, contrast, saturation and sharpness can be adjusted.
4. CABLE CONNECTIONS
DI/DO Connection
A: DO-, B: DO+ , C: DI+ , D: DI-
Sensor (DI) connection
The camera provides 1 channel D/I. It can be connected to either a voltage type
sensor or a relay type sensor as the following figures. It can be selected by software.
Input voltage range: 0VDC minimum to 5VDC maximum, Max 50mA
Input voltage threshold: 1.5V
Do not exceed the maximum input voltage or relay rate.
IPN6602HD-5215
DCBA
A : DO-
B : DO+
C : DI+
D : DI-
Red : AIN
White : AOUT
Cable arrange
LAN Port
Power DC 12V
Audio In
Audio Out
DI/DO
Caution
!
13
RC Series RC6602HD-5311
Installation Guide
www.rivatech.de
Alarm (DO) connection
Only the relay type is supported.
Relay Rating: Max 24VDC 50mA
Do not exceed the maximum relay rating.
Power Connection
A 12 DC power connector is required for this device.
Network Connection
This is a RJ45 LAN connector for 10/100 Base-T Ethernet. Connect a LAN cable.
Caution
!
DO
COM
Relay Type
Device
Internal
+3.3V
DI
COM
DI
COM
+
-
Relay Type
Voltage Type
+
-
Output of
Sensor
Output of
Sensor
Internal
Internal
+
-
14
RC Series RC6602HD-5311
Installation Guide
www.rivatech.de
Audio Input/Output Connection
Connect the audio input device such as a mike to the audio input port and the audio
output device such as the amplifier speaker to the audio output port.
Audio Input : Linein, 1.43Vp-p(M in 1.35Vp-p, max 1.49 Vp-p), 39 KΩ
Audio Output : Lineout, 46mW Power, 16 Ω
Do not connect the speaker without amplifier.
Caution
!
15
RC Series RC6602HD-5311
Installation Guide
www.rivatech.de
5. CONFIGURATION
5.1.Set up network environment
The default IP address of the device is 192.168.XXX.XXX. Users can identify the IP
address of the device from converting the MAC address’s hexadecimal numbers, which
is attached to the device. Be sure that the device and PC are on a same area network
before running the installation.
IP address : 192.168.xxx.xxx
Subnet mask: 255.255.0.0
5.1.1. Generic IP Environment
In case of generic private network environment where IP address 192.168.XXX.XXX
are used, users may view the live streaming images on a web page using the device’s
default IP address:
1. Convert the device’s MAC address to the IP address. Refer to the Hexadecimal-
Decimal Conversion Chart at the end of the manual.
(The MAC address of the device is attached on the side or bottom of the device.)
2. Start the Microsoft® Internet Explorer web browser and enter the address of the
device.
3. Web streaming and device configurations are supported through ActiveX program.
When the ActiveX installation window appears, authorize and install the ActiveX.
MAC address = 00-13-23-01-14-B1 → IP address = 192.168.20.177
Convert the last two set of hexadecimal numbers to decimal numbers.
16
RC Series RC6602HD-5311
Installation Guide
www.rivatech.de
5.1.2. Custom IP Environment
IPAdminTool and the manual are provided on USB stick or can download from
www.rivatech.de homepage.
IPAdminTool is a management tool, which automatically scans all of the network
products for users to perform administrative tasks, which includes network
configurations, firmware update, device reboot, and device organizations.
To modify the device’s default IP address for customized network area;
1. Find the device from the IPAdminTool’s list and highlight the device’s name.
2. Right-click the mouse and select “IP Address”; IP Setup window appears.
PC environment Info
Give new unique IP address in
last two sets and mirror other
information in other boxes
17
RC Series RC6602HD-5311
Installation Guide
www.rivatech.de
3. In the IP Setup’s window, information under ‘Local Network information’ displays the
user/PC’s network area information. Those information need to be incorporated to
the IP Address, Subnet Mask, Gateway, and DNS boxes, except the last 2 sets of
IP Address, which are to be the unique numbers for the device. Refer to the image
above for the setting
4. Click ‘Setup’ to complete the modification. When the dialog box appears to request
user name and password, enter the default value for the administrator account
(case-sensitive) as below:
ID:
root
Password:
pass
5.2. View video on web page
Type the proper IP address to view the live streaming images through a web browser.
The default username and password is
root / pass
.
1. The browser asks to install the ActiveX. Click Allow.
2. Setup.exe installation link or pop-up window appears, depends on Microsoft®
Internet Explorer version. Proceed with rest of setup installation.
18
RC Series RC6602HD-5311
Installation Guide
www.rivatech.de
Caution
!
3. Follow the instructions of the dialog boxes and complete the installation. Once the
installation is complete, start the web browser again and check if video stream is
displayed in the main view frame.
If “
This software requires the Microsoft XML Parser V6 or higher.
Please download MSXML6 from the Microsoft website to continue.
Error code: Cannot create XMLDOMDocument.
” message appears,
download and install the Microsoft Core XML Services (MSXML)
6.0.
19
RC Series RC6602HD-5311
Installation Guide
www.rivatech.de
Caution
!
5.2.1. View video using IPAdmin Tool
IPAdminTool automatically searches all activated network encoders and IP cameras
and shows the product name, IP address, MAC address and etc. IPAdminTool is
provided on USB stick or can download from www.rivatech.de homepage.
1. From the IPAdminTool’s product list, select the device by highlighting it.
2. Right-click the mouse and select Web view
3. The system’s default web browser opens the device’s address. Please take care
that the default system web browser is Microsoft® Internet Explorer to support
ActiveX plug-in.
Whether directly accessing the streaming video through typing IP
address on a web page or taking steps through IPAdminTool, the
ActiveX is needed to be installed for the Microsoft® Internet
Explorer to have the complete configuration privileges.
20
RC Series RC6602HD-5311
Installation Guide
www.rivatech.de
5.3. Reset
1. Push the Reset button and hold for 1~2 seconds.
2. Wait for the system to reboot.
5.4. Factory Default
If you reset your device to the factory default setting, all parameters including the IP
address will be initialized.
To proceed back to the Factory Default reset:
1. Push reset button and hold for 5 seconds.
2. Release the Reset button when power LED blinks.
3. Wait for the system to reboot.
The factory default settings can be inferred as follows:
More Information
To learn more about using other features of your devices, refer to the manuals as
“Web Interface Manual” or “VCAsys _Online_Help”, which is available on USB stick or
on www.rivatech.de homepage.
IP address: 192.168.xx.yy
Network mask: 255.255.0.0
Gateway: 192.168.0.1
User ID: root
Password: pass
Page is loading ...
Page is loading ...
Page is loading ...
Page is loading ...
Page is loading ...
-
1
-
2
-
3
-
4
-
5
-
6
-
7
-
8
-
9
-
10
-
11
-
12
-
13
-
14
-
15
-
16
-
17
-
18
-
19
-
20
-
21
-
22
-
23
-
24
-
25
Riva RC6602HD-5311 Installation guide
- Category
- Security cameras
- Type
- Installation guide
Ask a question and I''ll find the answer in the document
Finding information in a document is now easier with AI
Related papers
-
Riva RC6602HD-5311 Quick Installation Guide
-
Riva RC5510 Quick Installation Guide
-
Riva RC1202HD-6241 Quick Installation Guide
-
-
Riva RC3502HD-6311 Quick Installation Guide
-
Riva RC6802HD-6211 Installation guide
-
Riva RC3302HD-5344 Quick Installation Guide
-
Riva RC3502HD-5311 Quick Installation Guide
-
-
Riva RC3702HD-5314 Quick Installation Guide
