Intimus 45SC2 Operating instructions

Category
Paper shredders
Type
Operating instructions
IMPORTANT SAFETY NOTES
<< The machine may not be operated by more
than one person at any given time!
The machine was designed for safe operation
by “one person only”.
<< During the shredding process no other
work may be performed on the machine
(for example cleaning, etc.)!
<< The machine is not a toy, and is not suitable
for use by children!
The overall technical safety concept of
this machine (dimensions, feed openings,
emergency shutdown devices etc.) does not
provide for any guarantee regarding hazard-
free operation by children.
<< Danger of injury! Keep all
loose articles of clothing, ties,
jewelery, long hair or other loose
objects away from opening!
<< Danger of injury! Never insert ngers into
opening!
<< In case of danger switch the machine off
with the main switch, or with the emergency
switch, or unplug the machine!
<< Always unplug the machine from the
main power supply before opening the
machine!
Repairs may only be performed by trained
personnel!
AREA OF APPLICATION:
The intimus 45/60SC2/CC3/CC4/CC5/CC6 data
shredder is a machine used for shredding general
documents and
data carriers such CD’s, DVD’s, credit cards and
3.5” diskettes.
The machine must only be used to
shred paper, credit cards and CD’s,
DVD’s and 3.5” diskettes.
Shredding other sorts of data carriers
may cause damage to the machine (e.g.
damage to the cutters etc.).
INSTALLATION:
- Unpack the machine and put it together.
- Fit the plastic bag onto the bag frame.
- Connect the machine to the power with the plug
(1) (Fig. 2) (For information on the right fuse for
the plug see “TECHNICAL DATA”).
The socket outlet shall be installed
near the equipment and shall be easily
accessible!
Only operate the machine in enclosed
rooms at temperatures between 10°C
and 25°C!
3
9
10
11
4
6
7
8
2
1
12
13
5
90972 5 04/13
45SC2
45CC3
45CC4
45CC5
45CC6
60SC2
60CC3
60CC4
60CC5
60CC6
OPERATION
INITIATION
GB
g. 1
g. 2
g. 3
6 = Controldisplay(g.1)
“Material jam in machine”/
“Simultaneous material feed” / “Light
barrier covered when door opens or
when machine turned on”
For the procedures see the relevant
description under the “MALFUNCTION”
section.
a) “Material jam in machine”
Comes on when too much material has
been fed into the cutters. The cutters
jam, then run in reverse for a short time
and stop. The motor switches off.
b) “Simultaneous material feed”
Comes on when material has been fed
into both slots at the same time. The
cutters stop, then run in reverse for a
short time and stop. The motor switches
off.
c) “Light barrier covered
when door open”
Comes on when there is still material in
one of the two feed slots when the door
is opened. The cutters stop. The motor
switches off.
d) “Light barrier covered
when machine turned on”
Comes on when there is still material
in one of the two feed slots when the
machine is switched on.
CONTROLS:
1 = Mainplug(g.2)
When the machine is rst plugged in it is
not on.
2 = Functionbutton(g.1)
“Ready”/ “Off” / “Stop“
This button has three functions:
a) “Ready”
The machine changes to “Ready” if you
press this button briey.
At the same time the integral LED
display comes on.
b) “Off”
The machine switches off if it is in the
“Ready” mode and the button is held
down for about 3 seconds.
Note: The machine switches off
automatically if it is not used for about 5
minutes.
c) “Stop”
If you press this button briey when the
cutters are running they switch off and
stop.
3 = Forwardsbutton(g.1)
This button has two functions:
a) If this button is pressed briey, the
cutting mechanism runs forwards for a
few seconds, e.g. to remove remaining
material from the cutting mechanism.
At the same time the integrated LED
display lights up.
b) If this button is pressed and held
for approx. two secs., the cutting
mechanism runs forwards continually
and materials to be shredded can be fed
into the machine. At the same time the
integrated LED display lights up.
4 = Reversebutton(g.1)
If you press this button the cutters run
backwards for a short time. At the same
time the integral LED display comes on.
5 = Lightbarrier(Forwardmotion)(g.3)
The shredding procedure starts as soon
as material is fed into one of the two feed
slots. At the same time the integral forward
button LED display comes on.
Translation of the Original Operation Manual
Übersetzung der Originalbetriebsanleitung
5
The shredder may not be used as a step
ladder or as a seat. Danger of falling due
to breakage!
SWITCHING THE MACHINE ON:
Proceed as follows to switch the machine to “Ready”:
- Press the function button (2) briey.
- The function button (2) LED display comes on
for “Ready”.
- The machine is ready for operation.
MATERIAL FEED:
Feed paper into the cutting mechanism through the
paper feed slot (12) (g. 3).
Feed data carriers (CD, DVD or credit card) into the
cutting mechanism individually into the separate CD/
DVD feed slot (13) (g. 3).
The machine automatically switches to forwards
running, draws the material in and automatically
switches off after shredding.
When shredding papers, do not shred CD/
DVD at the same time, and vice versa!
Note: For shredding transparent lms, the machine
must be manually switched to forwards running (press
and hold the forwards button (3) for approx. 2 secs.).
By briey pressing the function button (2) (Stop
function), the shredding process can be stopped at
any time. To continue, press and hold the forwards
button (3) for approx. 2 secs.
If the machine is not used for a period of approx. 5
mins., it automatically switches off.
Never feed the shredder with a quantity
of material exceeding the maximum
indicated. Refer to the TECHNICAL DATA
section!
Should the machine become overloaded,
follow the instructions under “MATERIAL JAM
IN MACHINE” under “MALFUNCTIONS”.
Two separate collection containers ensure that
waste is separated properly.
EMPTYING THE
PAPER COLLECTION BAG (Fig. 4):
If the paper collection bag is full the machine switches
off. The control display (11) comes on. Proceed as
follows:
- Open the door. The control display (8) comes on.
If there is still material in one of the feed slots, the
control display (6) also comes on.
- Pull out the bag frame (16) together with the
attached paper collection bag (14) and tted CD/
DVD container (15) from the lower part of the
housing.
- Remove the CD/DVD container, take out the paper
collection bag and empty the contents. The control
display (11) goes out.
CONTROLS:
7 = Control display (Fig. 1)
“Oil cutters”
Comes on when the cutters in the cross
cut version must be oiled. The lubrication
procedure must be acknowledged on the
reverse button (4) (see description in “CUTTER
MAINTENANCE”).
8 = Control display (Fig. 1)
“Door open”/ “Door malfunction”
a) “Door open”
Comes on if the door on the lower part of the
machine is opened. The machine switches
off automatically and cannot be started as
long as the door remains open.
b) “Electrical fault”
Flashes when there is an electrical fault in
the door sensor. The machine switches off.
Please contact your dealer.
9 = Control display (Fig. 1)
“Motor overload” /
“Electrical fault”
To nd out what to do see the relevant description
under the “MALFUNCTION” section.
a) “Motor protection”
Comes on when the motor has been
overloaded and has switched off. The
machine cannot be started while the motor
is cooling down.
b) “Electrical fault”
Flashes when there is an electrical fault
inside the control board. At the same time the
function button (2) LED display ashes.
The machine switches off. Please contact
your dealer.
10 = Control display
“CD/DVD container full” (Fig. 1)
Comes on when the CD/DVD container is
full and must be emptied. The cutting unit for
reducing CD/DVD switches off. The emptying
procedure must be acknowledged on the
forward button (3).
Note: The cutting unit for reducing paper can
be used furthermore.
11 = Control display
“Paper collection bag full” (Fig. 1)
Comes on when the paper collection bag is
full and must be emptied. The cutting unit for
reducing paper switches off.
Note: The cutting unit for reducing CD/DVD
can be used furthermore.
12 = Paper feed slot (Fig. 3)
13 = CD/DVD feed slot (Fig. 3)
14 = Paper collection bag (Fig. 4)
15 = CD/DVD collection container (Fig. 4)
16 = Bag frame (Fig. 4)
17 = Oil reservoir (Fig. 4, 6)
- Attach the emptied bag to the bag frame (16), t the
CD/DVD container and slide the frame together with
the bag and CD/DVD container back into the lower
part of the housing.
- Close the door. The control display (8) goes out.
- If the control display (6) comes on, press the
forward button (3) briey. The remaining material in
the feed slot is shredded and the display go out.
Note: The machine will only run if the door is closed.
EMPTYING THE CD/DVD COLLECTION
CONTAINER (Fig. 4):
Note: The “CD container full” is monitored by counting
the number of shredding processes performed.
If the number of CD’s/DVD’s pre-programmed into
the control unit (about 20) is shredded the machine
switches off. The control display (10) comes on.
Proceed as follows:
- Open the door. The control display (8) comes on
and the forward button (3) LED display as well as
the control display (10) ashes.
- Pull out the bag frame (16) together with the
attached paper collection bag (14) and tted CD/
DVD container (15) from the lower part of the
housing, remove the CD/DVD container and empty
the contents.
- Press the forward button (3) briey to acknowledge
that the CD/DVD container has been emptied. The
counting process begins at zero again. The control
display (10) and the forward button (3) LED
display go out.
- Fit the emptied CD/DVD container to the bag frame
(16) and slide the frame together with the bag and
container back into the lower part of the housing.
- Close the door. The control display (8) goes out.
Note: The machine will only run if the door is closed.
DYNAMIC LOAD DISPLAY:
To prevent a material jam and thus ensure a continual,
effective destruction of the data carriers, the current
load level of the motor is displayed during the
shredding process by a coloured, diffuse light in the
feed slot as follows:
Green light: load < 50%
Yellow light: load 50 - 75%
Red light: load 75 - 100%
3
9
10
11
4
6
7
8
2
12
13
5
15
1417 16
90972 5 04/13
45SC2
45CC3
45CC4
45CC5
45CC6
60SC2
60CC3
60CC4
60CC5
60CC6
OPERATION
GB
g. 1 g. 3 g. 4
Translation of the Original Operation Manual
Übersetzung der Originalbetriebsanleitung
6
MATERIAL JAM IN THE MACHINE:
(Auto reverse function)
If a jam is caused by too much material being fed in
the following happens:
- The cutters jam, then run in reverse for a short
time (material is released) and stop. The motor
switches off. The control display (6) comes
on.
Proceed as follows:
Paper jam in paper feed slot (12)
- Remove the paper that has been fed back.
- The cutters now run forwards automatically and
shred the remaining paper in the cutters. During
the forward run the forward button (3) LED
display comes on. The control display (6)
goes out.
- Continue shredding with less paper.
Material jam in CD/DVD feed slot (13)
- Remove the returned material.
Remove the material carefully
because there is the risk of being
injured by the sharp cut surfaces.
- The remaining material to be cut is now
automatically fed to the cutters again and
shredded. During the forward run the forward
button (3) LED display comes on. The control
display (6) goes out.
- If the material to be cut has gone through continue
shredding with the right amount of material.
- If necessary, switch the cutters manually
alternately from forward to reverse until the
material has gone through completely and been
shredded.
SIMULTANEOUS MATERIAL FEED:
Should material be fed into the two feed slots at the
same time the following happens:
- The cutters jam, then run in reverse for a short
time (material is released) and stop. The motor
switches off. The control display (6) comes
on.
- Take the material out of one of the slots.
- Press the forward button (3) briey. The material
in the other slot is fed to the cutters and shredded.
The control display (6) goes out.
LIGHT BARRIER COVERED
WHEN DOOR OPENED:
Should there still be material in one of the two feed
slots when the door is opened, the motor switches
off and the cutters stop. The control display (6)
comes on.
Close the door and acknowledge the status by
pressing the forward button (3) briey. The existing
material is fed to the cutters and shredded.
LIGHT BARRIER COVERED
WHEN MACHINE TURNED ON:
Should there still be material in one of the two feed
slots when the machine is switched on the control
display (6) comes on.
Remove the material and acknowledge the status
by pressing the forward button (3) briey.
MOTOR PROTECTION:
Should the motor be overloaded it switches off. The
control display (9) comes on.
The machine can be started again after a cooling
down period of about 25 40 minutes (depending
on the model and the room temperature).
ELECTRICAL FAULT:
If the control display (9) ashes together with
the function button (2) LED display or only the
control display (8) ashesthere is an electrical
fault. The machine cannot be started.
In this case please contact your dealer.
FAULT CHECK LIST:
Should the machine not work, check the following
points:
- is the plug connected to the power supply?
- is the door closed?
- is the paper collection bag full?
Follow the instructions for “EMPTYING THE
PAPER COLLECTION BAG“.
- Is the CD/DVD collection container full?
Follow the instructions for “EMPTYING THE CD/
DVD COLLECTION CONTAINER”.
- Is there a material jam in the machine?
Follow the instructions in “MATERIAL JAM IN
THE MACHINE”.
- Is the motor overloaded?
See “MOTOR PROTECTION”.
If none of these test points apply, please
contact your dealer.
17
90972 5 04/13
45SC2
45CC3
45CC4
45CC5
45CC6
60SC2
60CC3
60CC4
60CC5
60CC6
MALFUNCTIONS
MAINTENANCE / DISPOSING
TECHNICAL DATA SPECIAL ACCESSORIES
GB
CUTTER MAINTENANCE (CROSS CUT):
Cross cut cutters must be oiled after a specic
operating time.
If the control display (7) comes on proceed as
follows:
Open the door. The control display (8) comes on and
the reverse button (4) LED display as well as the control
display (7) ashes. Remove the oil reservoir (17) (Fig. 6)
from the holder in the door and close the door again.
Pour a little oil onto a sheet of paper and then feed this
through the paper feed slot (12) onto the cutters.
The paper is drawn in and in this way the oil is distributed
to the cutters.
Note: This procedure is acknowledged as follows to turn
off the display after the cutters have been oiled:
- Open the door until the control display (8) lights up. The
control displays (7) and (4) ash.
- Press the reverse button (4) and keep it held down until
the control display (7) goes out.
CLEANING THE PHOTOCELLS (Fig. 5):
If paper particles should come to rest in the inlet guide (for
example after a paper jam) it is possible that the machine will
not turn off, due to the broken light barrier.
To remove these paper strips and also to clean the photocell,
pass another sheet of paper through the feed slot, or switch
the machine to reverse and wipe both “eyes” of the photocell
with a brush.
- Close the door again.
The cutters now start a cleaning cycle automatically (forward
and reverse run) and then switch off. The machine is ready
for use again. Should you need to re-order the special oil see
“SPECIAL ACCESSORIES”.
AUTOMATIC ENERGY SAVING:
If the machine is not used for a while it automatically switches
off after about 5 minutes. The function button (2) LED display
for “Ready” goes out. Press the function button briey to
turn it on again.
DISPOSING OF THE MACHINE:
Dispose of the machine in an environmentally
friendly fashion at the end of its useful service life.
Do not dispose of any of the parts included in the
machine or its packaging with household waste.
g. 5
g. 6
Translation of the Original Operation Manual
Übersetzung der Originalbetriebsanleitung
7
Model Typ Cutting width Cutting capacity Working width Noise level Dimensions Weight
paper / CD,DVD paper / CD,DVD W x D x H
intimus 45SC2 278-4S 3.8 mm / 8 mm 22-24 sheets* / 1 piece 235 mm app. 55 dB(A) 450 x 390 x 650 mm 31 kg
intimus 45CC3 278-4C 3.8x30 mm / 8 mm 13-15 sheets* / 1 piece 235 mm app. 55 dB(A) 450 x 390 x 650 mm 32 kg
intimus 45CC4 278-2C 1.9x15 mm / 8 mm 10-11 sheets* / 1 piece 235 mm app. 55 dB(A) 450 x 390 x 650 mm 32 kg
intimus 45CC5 278-1C 0.8x12 mm / 8 mm 5-6 sheets* / 1 piece 235 mm app. 55 dB(A) 450 x 390 x 650 mm 32 kg
intimus 45CC6 278-1CF 0.8x4.5 mm / 8 mm 5-6 sheets* / 1 piece 235 mm app. 55 dB(A) 450 x 390 x 650 mm 32 kg
intimus 60SC2 279-4S 3.8 mm / 8 mm 22-24 sheets* / 1 piece 235 mm app. 55 dB(A) 450 x 390 x 770 mm 33 kg
intimus 60CC3 279-4C 3.8x30 mm / 8 mm 13-15 sheets* / 1 piece 235 mm app. 55 dB(A) 450 x 390 x 770 mm 34 kg
intimus 60CC4 279-2C 1.9x15 mm / 8 mm 10-11 sheets* / 1 piece 235 mm app. 55 dB(A) 450 x 390 x 770 mm 34 kg
intimus 60CC5 279-1C 0.8x12 mm / 8 mm 5-6 sheets* / 1 piece 235 mm app. 55 dB(A) 450 x 390 x 770 mm 34 kg
intimus 60CC6 279-1CF 0.8x4.5 mm / 8 mm 5-6 sheets* / 1 piece 235 mm app. 55 dB(A) 450 x 390 x 770 mm 34 kg
Model Power supply data
supply voltage/frequency · current consumption · power
intimus 45/60SC2
220-230V/50Hz · 3,0 amps · 0,7 kW 120V/60Hz · 5,6 amps · 0,7 kW 100V/50/60Hz · 7,0 amps · 0,7 kW
intimus 45/60CC3+CC4+CC5
220-230V/50Hz · 3,0 amps · 0,55 kW 120V/60Hz · 5,6 amps · 0,55 kW 100V/50/60Hz · 7,0 amps · 0,55 kW
intimus 45/60CC6
220-230V/50Hz · 3,0 amps · 0,7 kW 120V/60Hz · 5,6 amps · 0,7 kW 100V/50/60Hz · 7,0 amps · 0,7 kW
Description Order-No.
Plastic bag, 440x330x600x0.05 mm (45) 83079
Plastic bag, 440x330x950x0.05 mm (60) 99977
Lubricant, 110 ml bottle 88035
Note: For orders of special accessories and spare
parts, please contact your dealer.
* based on A4-paper 70g/m² at 230V/50Hz
Pre-fusing (slow-blow): 220-230V = 10 amps / 120V = 15 amps / 100V = 15 amps
90972 5 04/13
45SC2
45CC3
45CC4
45CC5
45CC6
60SC2
60CC3
60CC4
60CC5
60CC6
53
90972 5 04/13
45SC2
45CC3
45CC4
45CC5
45CC6
60SC2
60CC3
60CC4
60CC5
60CC6
54
90972 5 04/13
45SC2
45CC3
45CC4
45CC5
45CC6
60SC2
60CC3
60CC4
60CC5
60CC6
55
90972 5 04/13
Dieses Papier ist aus 100 % Altpapier ohne optische Aufheller hergestellt
This paper made from 100 % unbleached recycled paper
Papier recyclable à 100 %
International Network
Headquarters
USA MARTIN YALE Industries +1 / 260 563-0641
251 Wedcor Avenue fax +1 / 260 563-4575
Wabash, IN 46992 [email protected]
www.martinyale.com
Germany MARTIN YALE INTERNATIONAL GmbH +49 / (0) 7544 60-0
Bergheimer Straße 6-12 fax +49 / (0) 7544 60-248
88677 Markdorf / Bodensee [email protected]
www.martinyale.de, www.intimus.com
Branch Ofces
South Africa MARTIN YALE Africa +27 / (0) 11 838 72 81
Unit B3 Mount Royal Business Park fax +27 / (0) 11 838 73 22
657 James Street, Halfway House [email protected]
Marshall Town, Johannesburg
P. O. BOX 1291, Houghton 204
www.martinyale.co.za
United Kingdom MARTIN YALE International +44 / (0) 1293 44 1900
Unit C 2 The Fleming Centre, Fleming Way fax +44 / (0) 1293 61 11 55
Crawley, West Sussex, RH10 9NN [email protected]
www.intimus.co.uk
France MARTIN YALE International S.A.R.L. +33 / (1) 70 00 69 00
40 Avenue Lingenfeld fax +33 / (1) 70 00 69 24
77200 Torcy [email protected]
www.martinyale.fr
Spain MARTIN YALE Ibérica S.L. +34 / 9 02 22 31 31
Avenida de la Platja, 120 bajos fax +34 / 9 02 22 31 32
08930 Sant Adrià de Besòs, Barcelona [email protected]
www.martinyale.es
Italy MARTIN YALE Italia srl [email protected]
Via A. Manzoni, 37
20900 Monza (MB)
www.martinyale.it
Sweden MARTIN YALE Nordic AB +46 / 8 556 165 80
Rotebergsvägen 1 fax +46 / 8 748 02 85
192 78 Sollentuna [email protected]
www.martinyale.se
P.R. China MARTIN YALE International Trading (Beijing) +86 / 10 844 710 71 / 72 / 73
Room 260D, C Building fax +86 / 10 844 710 75
Guojiang no.2 Dong Sanhuan Bei Lu [email protected]
Chaoyang District, Beijing 100027, PRC
www.martinyale.com.cn
  • Page 1 1
  • Page 2 2
  • Page 3 3
  • Page 4 4
  • Page 5 5
  • Page 6 6
  • Page 7 7
  • Page 8 8
  • Page 9 9
  • Page 10 10
  • Page 11 11
  • Page 12 12
  • Page 13 13
  • Page 14 14
  • Page 15 15
  • Page 16 16
  • Page 17 17
  • Page 18 18
  • Page 19 19
  • Page 20 20
  • Page 21 21
  • Page 22 22
  • Page 23 23
  • Page 24 24
  • Page 25 25
  • Page 26 26
  • Page 27 27
  • Page 28 28
  • Page 29 29
  • Page 30 30
  • Page 31 31
  • Page 32 32
  • Page 33 33
  • Page 34 34
  • Page 35 35
  • Page 36 36
  • Page 37 37
  • Page 38 38
  • Page 39 39
  • Page 40 40
  • Page 41 41
  • Page 42 42
  • Page 43 43
  • Page 44 44
  • Page 45 45
  • Page 46 46
  • Page 47 47
  • Page 48 48
  • Page 49 49
  • Page 50 50
  • Page 51 51
  • Page 52 52
  • Page 53 53
  • Page 54 54
  • Page 55 55
  • Page 56 56

Intimus 45SC2 Operating instructions

Category
Paper shredders
Type
Operating instructions

Ask a question and I''ll find the answer in the document

Finding information in a document is now easier with AI