DCS BGB48-BQR User manual

THE PROFESSIONAL

36/48” BGB GRILL

Use and Care Guide

MODELS:

BGB36-BQAR

BGB48-BQAR

BGB48-BQR

Page is loading ...

1

Thank you for selecting this DCS Professional “BGB” Series Grill. Because of these appliances’ unique features we

have developed this Use and Care Guide. It contains valuable information on how to properly install, operate and

maintain your new appliance for years of safe and enjoyable cooking.

To help serve you better, please fill out and submit your Product Registration by visiting our website at

www.dcsappliances.com and selecting “Customer Care” on the home page and then select “Product Registration”.

In addition, keep this guide handy, as it will help answer questions that may arise as you use your new appliance.

For your convenience, product questions can be answered by a DCS Customer Care Representative at

1-888-936-7872, or email: customer[email protected].

NOTE: Inspect the product to verify that there is no shipping damage. If any damage is detected, call the shipper

and initiate a damage claim. DCS by Fisher & Paykel is not responsible for shipping damage.

DO NOT discard any packing material (box, pallet, straps) until the unit has been inspected.

WARNING!

Do not try lighting this appliance without reading the “Lighting Instructions” section of this manual.

Improper installation, adjustment, alteration, service or maintenance can cause property damage,

injury or death. Read the installation, operating and maintenance instructions thoroughly before

use, installing or servicing this equipment. This outdoor cooking gas appliance is not intended to be

installed in or on recreational vehicles , boats or in a non-ventilated room. For outdoor use only.

WARNING

1

. Do Not store or use gasoline or any other flammable vapors and liquids in the vicinity of

this or any other appliance.

2.

An LP cylinder not connected for use shall not be stored in the vicinity of this or any

other appliance.

DANGER

What To Do If You Smell Gas:

1.

Shut off gas to the appliance.

2.

Extinguish any open flames.

3.

Open lid.

4. If odor continues, keep away from the appliance and immediately call your gas supplier

or your fire department.

PLEASE RETAIN THIS MANUAL FOR FUTURE REFERENCE.

A MESSAGE TO OUR CUSTOMERS

NOTE: Please write the Model, Code, and Serial Numbers on this page for reference (can be found on the inside,

right side panel behind the drip pan handle. See page 17.)

MODEL NUMBER CODE SERIAL NUMBER

2

S

AFETY PRACTICES & PRECAUTIONS 3-5

GRILL MODELS 6

INSTALLATION

Locating Grill / Built-in Clearances 7-9

Built-in Construction Details 10-11

Gas Hook-up 12-15

Leak Testing 16

Burner Adjustment 17

Radiant Assembly 18

Installer Checklist 19

USING THE GRILL

Lighting Instructions 20

Grilling 21-22

USING THE SMOKER SYSTEM 23

USING THE ROTISSERIE 24-27

CARE & MAINTENANCE 28-30

TROUBLESHOOTING 31

SERVICE 32

WARRANTY 33-34

TABLE OF CONTENTS

3

IMPORTANT SAFETY NOTICE!

Certain Liquid Propane dealers may fill liquid propane cylinders for use in the grill beyond cylinder filling capacity.

This “Overfilling” may create a dangerous condition.

“Overfilled” tanks can build up excess pressure. As a safety device, the tank pressure relief valve will vent

propane gas vapor to relieve this excess pressure. This vapor is combustible and therefore can be ignited. To

reduce this danger, you should take the following safety precautions:

1.

When you have your tank filled, be sure you tell the supplier to fill it to no more than 3/4 (75%) of its total

capacity.

2

. If you own or use a spare tank, or have a disconnected tank, you should NEVER

store it near or under the grill/cart unit or heat box, or near any other ignition

or heat source. A metallic sticker with this warning is provided with the grill to

remind you, your family and all others who may use your BBQ grill of these

safety precautions. Install this sticker close to your barbeque grill.

3. Do not store a full tank in direct sunlight.

WARNING!

Do not try lighting this appliance without reading the “LIGHTING INSTRUCTIONS”

section of this manual. This grill is for outdoor use only.

WARNING!

Push and hold the igniter button, turn the selected burner knob to “SEAR”. If

burner does not light in 4 to 5 seconds turn knob “OFF” and wait 5 minutes before

trying again for any accumulated gas to dissipate.

■

Begin by insuring proper installation and

servicing. Follow the installation

instructions within this manual. Have your

grill installed by a qualified installer. Have

the installer show you where the gas supply

shut-off valve is located so that you know

where and how to shut off the gas to the

grill. If you smell gas, your installer has not

done a pr

oper job of checking for leaks. If

the connections are not perfectly sealed,

you can have a small leak and therefore a

fain

t gas smell. Finding a leak is not a “do-

it-yourself ” procedure. Some leaks can

only be found with the burner control in

the

“

ON” position and this must be done by

a qualified technician.

■

Children should not be left alone or unattended in an area where the grill is being used. Never allow them to sit,

stand or play on or around the grill at any time. When in use, portions of the grill get hot enough to cause

severe burns.

■

Do not store items of interest to children around or below the grill, in the cart or masonry enclosure. Never

allow children to crawl inside a cart or enclosure.

■

Never attach or disconnect an LP cylinder, or move or alter gas fittings when the grill is in operation or is hot.

■

Clean and perform general maintenance on the grill twice a year. Watch for corrosion, cracks, or insect activity.

Check the regula

t

or

, hoses, burner ports, air shutter, and venturi/valve section carefully. Always turn off gas at

the source (tank or supply line) prior to inspecting parts.

SAFETY PRACTICES & PRECAUTIONS

• Always follow lighting instructions.

• Lid must be opened before lighting

the grill.

• Check for gas leaks before lighting.

• Never lean over an open grill when

lighting. Serious burns may result.

• Hot surfaces surrounding grill

grates could cause serious burns.

• Always leave at least 12" clearance

tocombustibles around the grill.

• Never store a spare LP cylinder

under or near this unit.

• Never fill the tank beyond 3/4 full. A

fire causing death or serious injury

may occur.

WARNING

Sticker

4

For personal safety, wear proper apparel. Loose fitting garments or sleeves should never be worn while using

this appliance. Some synthetic fabrics are highly flammable and should not be worn while cooking. Only certain

types of glass, heat-proof glass ceramic, earthenware, or other glazed utensils are suitable for grill use. Use of

these types of materials may break with sudden temperature changes. Use only on low or medium heat settings

according to the manufacturer’s directions.

WARNING!

Spiders and insects can nest in the grill burners , causing gas not to flow through the burner. The gas will flow from

the front of the burner into the control panel. This is a very dangerous condition which can cause a fire to occur

behind the valve panel, thereby damaging the grill components and making it unsafe to operate.

WARNING!

Keep the area surrounding the grill free from combustible materials, trash, or combustible fluids and vapors such as

gasoline or charcoal lighter fluid. Do not obstruct the flow of combustion and ventilation air.

WARNING!

Never use the grill in windy conditions. If located in a consistently windy area (oceanfront, mountaintop, etc.) a

wind break will be required. Always adhere to the specified clearances listed.

GRILL PLACEMENT

■

After a period of storage or non-use (such as over the winter), the gas grill should be checked for gas leaks,

deterioration, proper assembly, and burner obstructions before using.

■

Never let clothing, pot holders or other flammable materials come in contact with or get too close to any grate,

burner or hot surface until it has cooled. Fabric may ignite and result in personal injury.

■

Do not heat unopened food containers as a build-up of pressure may cause the container to burst.

■

Always use a covered hand when opening the grill lid and only do so slowly to allow heat and steam to escape.

■

Never lean over an open grill. When lighting a burner, always pay close attention to what you are doing. Be

certain you are pushing the ignition button when you attempt to light the grill.

■

After lighting burners, make sure burners are operating normally (see page 17).

■

When using the grill, do not touch the grill burner, grate, or immediate surrounding area as these areas become

extremely hot and could cause burns.

■

Grease is flammable. Let hot grease cool before attempting to handle it. Avoid letting grease deposits collect in

the drip pan. Clean often.

■

D

o not use aluminum foil to line drip pans or grill grates or radiants. This can severely upset combustion air flow

or trap excessive heat in the control area. The result of this can be melted knobs or damaged ignition

components.

■

Do not operate with a damaged cord or plug.

SAFETY PRACTICES & PRECAUTIONS

PREFERRED

AIR FLOW

GRILL EXHAUST

EXHAUST

FLAME

BURNER

Wind hitting the

grill while in use,

especially winds

blowing into or

across this hood

gap, can cause

poor performance

and in some cases

can cause the

control panel to

get dangerously

hot.

If wind is an

issue, a wind

screen should

be added. The

wind screen

should be

higher than

the top of the

opening in the

back of the

grill and

minimum of 3”

clearance

from the back

of the grill for

the lid .

WIND SCREEN

W

IN

D

15” min.

3”

min.

WIND

P RI

M

AR

Y

IN

T

AK E

AIR F

L

OW

EXHAUST VENT FLOW

FLAME LIFT

5

■

When using the side burners always use flat bottomed pans which are large enough to cover the side burner.

Adjust the flame so that it heats only the bottom of the pan to avoid ignition of clothing. Position handles inward

away from open edges of the unit to avoid burns associated with unintentional spillovers. Hold the handle of the

pan to prevent movement of it when turning or stirring food. For proper lighting and performance of the burners

k

eep the ports clean. It is necessary to clean periodically for optimum performance.

■

Clean the grill with caution. Avoid steam burns; do not use a wet sponge or cloth to clean the grill while it is hot.

Some cleaners produce noxious fumes or can ignite if applied to a hot surface.

■

Be sure all grill controls are turned off and the grill is cool before using any type of aerosol cleaner on or around

the grill. The chemical that produces the spraying action could, in the presence of heat, ignite or cause metal

parts to corrode.

■

Do not use the grill for cooking excessively fatty meats or products which promote flare-ups.

■

Never grill without the drip pan and grease tray in place and pushed all the way to the back of the grill. Without it

hot grease could leak downward and produce a fire or explosion hazard.

■

Do not operate the grill under unprotected combustible construction. Use only in well ventilated areas. Do not

use in buildings, garages, sheds, breezeway, covered structure or other such enclosed areas. This unit is for

outdoor use only.

■

If a cart unit is stored indoors, ensure that it is cool, fold the side shelf down, then push, never pull, the grill and

never push or pull on the side shelves. If LP, the cylinder must be unhooked and the LP cylinder stored outside in

a well ventilated area, out of reach of children.

■

Never use the grill in a windy area.

■

Do not use charcoal or lighter fluid in the outdoor grill.

■

Keep any electrical supply cord, or the rotisserie motor cord away from the heated areas of the grill and water

(pools, fountains, puddles).

■

Never use a dented or rusty LP tank. Keep the ventilation openings of the cylinder enclosure free and clear from

debris.

■

Use only dry potholders; moist or damp potholders on hot surfaces may cause burns from steam. Do not use a

towel or bulky cloth in place of potholders. Do not let potholders touch hot portions of the grill or burner grate.

■

Have an ABC rated Fire Extinguisher accessible – never attempt to extinguish a grease fire with water or other

liquids.

■

To avoid burns when cooking, use long handled BBQ tools.

■

D

o not mov

e the applianc

e dur

ing its use

.

■

This unit is for outdoor use only! Do not operate in enclosed areas. This could result in carbon monoxide build-up

which w

ould result in injury or death.

■

When using a grill, be sure that all parts of the unit are firmly in place and that the grill is stable (can’t be tipped

over).

■

To put out flare-ups, adjust the controls to lower the temperature

■

CALIFORNIA PROPOSITION 65-WARNING: The Burning of gas cooking fuel generates some by-products which are

on the list of substances which are known by the State of California to cause cancer or reproductive harm.

California law requires businesses to warn customers of potential exposure to such substances. To minimize

exposure to these substances, always operate this unit according to the Use and Care Guide, ensuring you

provide good ventilation when cooking with gas.

■

This outdoor cooking gas appliance is not intended to be installed in or on recreational vehicles, trailers and/or

boats.

Note:

This product must be installed by a licensed plumber or gas fitter when installed within the Commonwealth of

Massachusetts.

SAFETY PRACTICES & PRECAUTIONS

Page is loading ...

7

Important!

B

efore installation, remove shipping brackets from the grill. To

do so, loosen the 4 screws on the bottom sides of the grill which

hold the brackets to the grill. Slide the shipping brackets off

and retighten the screws.

LOCATION:

When determining a suitable location take into account concerns

such as exposure to wind, proximity to traffic paths and keeping any gas or electrical supply lines as short as

possible and away from heat sources. Locate the grill only in a well ventilated area. Do not build the grill under

overhead unprotected combustible construction. Never locate the grill in a building, garage, breezeway, shed or

other such enclosed areas. During heavy use, the grill will produce a lot of heat and smoke. Ensure there is

adequate area for it to dissipate.

If locating the grill in a windy area, try to locate the grill so the prevailing wind will blow air at the front of the

grill as shown in Fig. 02. This will assist the grill in venting hot air thru the back of the grill. In addition, this will

help keep any smoke from blowing at someone who is cooking on the grill. If you have to locate the grill in a

windy area where the prevailing wind is at the rear of the grill, a windbreak must be installed. The windbreak

should be made such tha

t it will block wind from entering the exhaust vent in the rear of the unit as shown in

Fig. 02.

As high-performance gas appliance, your grill requires significant amounts of air to support the combustion

process. Your grill is designed to take air in through the valve panel area, and send the exhaust products out

through the exhaust gap at the rear of the hood. Using your grill in windy conditions can disrupt the proper flow

of air though your grill, leading to reduced performance, or in certain severe cases, causing heat buildup in the

valve panel area. This can lead to problems such as having the knobs melt, or burn hazards when the valve

panel surfaces become too hot to touch.

During high wind conditions, it is best if you don’t use your grill. If you live in an area that is subject to frequent

high winds, or a steady directional wind, then the installation of a suitable windbreak may be advised. If you

have a grilling cart, it is best to position the unit so the prevailing wind blows into the valve panel, thus

supporting the proper airflow. Winds hitting the back of the grill directly are the most likely to cause problems,

although wind blowing along the exhaust gap in the rear can also be problematic.

Please note that damage to your grill resulting from use in windy conditions, such as melted knobs or igniter

wires, or valve panel discoloration from heat build-up, are excluded from warranty coverage.

Important!

Gas fittings, r

egula

tor, and installer supplied shut-off valves must be easily accessible.

INSTALLATION

LOCATING GRILL/BUILT-IN CLEARANCES

PREFERRED

AIR FLOW

GRILL EXHAUST

EXHAUST

FLAME

BURNER

Wind hitting the

grill while in use,

especially winds

blowing into or

across this hood

gap, can cause

poor performance

and in some cases

can cause the

control panel to

get dangerously

hot.

GRILL PLACEMENT

FIG. 01

Shipping Brackets

If wind is an

issue, a wind

screen should

be added. The

wind screen

should be

higher than

the top of the

opening in the

back of the

grill and

minimum of 3”

clearance

from the back

of the grill for

the lid .

WIND SCREEN

W

IN

D

15” min.

3”

min.

WIND

P RI

M

AR

Y

IN

T

AK E

AIR F

L

OW

EXHAUST VENT FLOW

FLAME LIFT

FIG. 02

8

48 BQAR = 53-1/4"

48 BQR = 53-7/16"

3

6 BQAR = 41-5/8"

(

with rotisserie motor mounted)

4

8" Models = 47-7/8"

3

6" Models = 35-7/8"

(without rotisserie motor moun ted)

rotisserie

motor

2

4-1/4"

10-1/2"

2

6-1/2"

grill

exhaust

3

" (to non-combustible

construction / minimum

lid clearance)

1

0 "

2

5-1/2"

2

2"

Bottom of

support flange

3

"

FIG. 03

INSTALLATION

LOCATING GRILL/BUILT-IN CLEARANCES

Clearances to Non-Combustible Construction*

Clearances to Non-Combustible Construction*:

A minimum of 3" clearance from the back of the grill to non-combustible construction is required for the

p

urpose of allowing the lid to open fully. It is desirable to allow at least 6" rear and side clearance to non-

combustible construction above the cooking surface for counter space. If you’ll be using the rotisserie option,

the space is essential for motor and skewer clearance. The grill can be placed directly adjacent to non-

combustible construction below the cooking surface. (Fig. 03)

WARNING!

Failur

e to maintain required clearances creates a fire hazard that may result in property damage or serious personal

injury.

WARNING!

The BGB Grill is designed to function in an open area. Recommended minimum clearances should be maintained to

all surfaces (combustible and noncombustible) for optimum performance. Noncombustible material within the min-

imum clearance area could result in discoloration or deterioration.

WARNING!

I

f a noncombustible material such as stucco is covering a combustible material such as wood, the minimum clear-

ance distance needs to be held to the wood. The presence of a noncombustible material inside the clearance zone

does not eliminate the minimum clearance zone to combustible material.

* DEFINITION OF NONC

OMBUSTIBLE M

ATERIAL

- M

a

terial which is not capable of being ignited and burned, such as

ma

t

er

ials c

onsisting en

tir

ely of, or a combination of, steel, iron, brick tile, concrete, slate, and plaster.

Clearances to Combustible Construction**:

Minimum of 12" from the sides and rear of grill must be maintained to adjacent vertical combustible

construction, above the counter top level. You should take in account that there is a large volume of heat, and

smoke will exhaust from the rear of the grill. This may discolor or damage unprotected areas (Fig. 04). Do not

install under unprotected combustible construction without using a fire safe ventilation system.

A 12" minimum clear

anc

e must be main

tained under the c

oun

t

er top to combustible construction. The clearance

can be modified by a use of an insulated jacket.

9

GENERAL

The grill is designed for easy placement into built-in masonry enclosures. For non-combustible applications the

grill drops into the opening shown in Fig. 05 and hangs from its side flanges. A deck is not required to support it

from the bottom. When using the insulated jacket in a combustible enclosure application, see the bottom of

F

ig

. 05. The insulation jacket assembly must be supported from the bottom by a ledge on each side and back or

a solid deck.

A carpenter’s “spirit level” should be used to assure that the unit is level both front-to-back and side-to-side. If it

is not level, burner combustion may be erratic or the unit may not function efficiently for grease flow. If the floor

is unev

en or has a decided slope, re-leveling may be required after each moving of a freestanding unit.

INSULATED JACKET:

WARNING!

Installing this product into a combustible enclosure without an insulated jacket could result in fire, property

damage and personal injur

y

.

If the grill is to be placed into a combustible enclosure, an approved insulated jacket is necessary. Insulated

jackets ar

e a

v

ailable fr

om your dealer. Use only the DCS insulated jacket which has specifically been designed

and tested for this purpose. Review the detail drawing shown (Fig. 05) and take into account the provisions

shown for gas line hook-up clearance in the right rear corner. It is required that ventilation holes are provided in

the enclosure t

o elimina

t

e the potential build-up of gas in the event of a gas leak. The supporting ledges or

deck must be level and flat and strong enough to support the grill and insulated jacket. The counter should also

be level.

INSTALLATION

LOCATING GRILL/BUILT-IN CLEARANCES

r

otisserie

motor

2

4-1/4"

1

0-1/2"

2

6-1/2"

g

rill

e

xhaust

1

2" min. (to combustible

c

onstruction)

1

0 "

2

5-1/2"

22"

2

"

Bottom of

support flange

1

2" min.

12" min.

FIG. 04

Clearances to Combustible Construction**

** DEFINITION OF COMBUSTIBLE MATERIAL - Any materials of a building structure or decorative structure made of

wood, compressed paper, plant fibers, vinyl/plastic or other materials that are capable of transferring heat or

being ignited and burned. Such material shall be considered combustible even though flame-proofed, fire-retar-

dant treated, or painted surface or plastered.

Important!

It is required that a minimum of (3) 10 sq. inches of ventilation opening be provided for both the left and right

sides, as well as the back of enclosure (Fig. 06 and 07), in order to safely dissipate unburned gas vapors in the

event of a gas supply leak.

WARNING!

Note specific built-in enclosure ventilation requirements. See text and Fig. 06.

10

grill

exhaust

3" (to non-combustible

construction / minimum

lid clearance)

12" (to combustible

construction)

1

0"

2

2"

25-1/2"

1-1/2"

2"

13-3/4"

Standard layout for non-combustible enclosure:

NOTE: If using a backguard

apron or rear wall, locate

electrical service on the

right hand side for rotisserie

motor connection

48" Models = 45-3/4"

36" Models = 34-1/2"

Bottom of

support flange

3" Min. for Lid

Clearance

3" Min. for Lid

Clearance

48" Models = 46"

36" Models = 34"

48" Models = 51-5/8"

36" Models = 40-1/2"

48" Models = 46"

36" Models = 34"

23-3/4"

3"

18-1/2"

20"

11-1/8"

35-1/2"

Max.

opening for access

doors/drawers

(see Fig. 06 & 07 for

ordering information)

4" x 4" opening

for gas supply

line

opening for access doors/

drawers

(see Fig. 06 & 07 for

ordering information)

4" x 4" opening

for gas supply

line

22-3/4"

18-1/2"

20"

10-1/8"

35-1/2"

Max.

Layout for insulated jacket only - combustible enclosure:

NOTE: If using a backguard

apron or rear wall, locate

electrical service on the

right hand side for rotisserie

motor connection

10 in.

2

min.

ventilation

left hand

side

10 in.

2

min.

ventilation

on the right

hand side

10 in.

2

Min. ventilation

on the back side

1" Min.

10 in.

2

min.

ventilation

left hand

side

10 in.

2

min.

ventilation

on the right

hand side

10 in.

2

min. ventilation

on the back side

1" Min.

WARNING!

If installing the grill into a non-combustible enclosure, all combustible

construction must still be outside the 12 inch clearance zone. If your

island is made of stucco over the top of wooden studs, the wood can not

be inside the 12 inch clearance zone to combustible, even though the

stucco is what is touching the grill area.

INSULATED JACKET

Size Part No.

36 70167

48 70172

INSTALLATION

BUILT–IN CONSTRUCTION DETAILS

FIG. 05

11

FIG. 06

Access Doors -

Cutout dimensions

A

90º

B

Vent*

MODEL NUMBER A B

(+0,-1/8) (+1/8,-0)

ADN 20x48 46” 20”

ADN 20x36 34” 20”

ADN 20x30 28” 20”

ADN 20x24 22” 20”

Cutout for Access Doors

Access Drawers

Cutout dimensions

NO

TE: The cutout of each corner should be 90

º

angle in or

der for the access

drawers to fit properly.

* Island installa

tion to use minimum of 3 vents, 10 square inches per vent (typical).

*

* For proper support and drawer operation, insure that support boards are

i

nstalled per In

stallation Guide instructions.

MODEL NUMBER A B C

(+0,-1/8) (+1/8,-0)

ADR48 46” 20”

ADR36 34” 20”

ADR30 28” 20”

ADR24 22” 20”

24-1/2”

(Min,

All

Models)

N

OTE: The cutout of each corner should be 90

º

a

ngle in order

for the access doors to fit properly.

* Island installation to use minimum of 3 vents, 10 square

inches per vent (typical).

FIG. 07

INSTALLATION

BUILT–IN CONSTRUCTION DETAILS

12

GAS REQUIREMENTS

V

erify the type of gas supply to be used, either natural or LP, and make sure the marking on the appliance rating

plate agrees with that of the supply. The rating plate is located underneath the unit bottom. Never connect an

unregulated gas line to the appliance. You must use the gas regulator provided with the unit, even if the supply

is controlled.

An installer-supplied gas shut-off valve must be installed in an easily accessible location. All installer supplied

parts must conform to local codes, or in the absence of local codes, with the National Electrical Code, ANSI/NFPA

70 or the Canadian Electrical Code, CSA C22.1, and the National Fuel Gas Code, ANSI Z223.1 or CAN/CGA-B149.1

Natural Gas Installation Code or CAN/CGA-B149.2 Propane Installation Code.

All pipe sealants must be an approved type and resistant to the actions of LP gases. Never use pipe sealant on

flare fittings. All gas connections should be made by a qualified technician and in accordance with local codes

and ordinances. In the absence of local codes, the installation must comply with the National Fuel Gas Code

ANSI Z223.1. Gas conversion kits are available from the factory. When ordering gas conversion kits, have the

model number, and the type of gas (natural or LP) from your grill.

TOTAL GAS CONSUMPTION OF THE GRILL WITH ALL BURNERS ON HI:

BGB48-BQR - 126,500 Btu/hr BGB48-BQ

AR - 121,500 Btu/hr BGB36-BQAR - 92,500 Btu/hr

The appliance and its individual shut-off valve must be disconnected from the gas supply piping system during

any pressure testing of that system at test pressures in excess of 1/2 PSIG (3.5 kPa.) The appliance must be

isolated from the gas supply piping system by closing its individual manual shut-off valve during any pressure

testing of the gas supply piping system at test pressures equal to or less than 1/2 PSIG (3.5 kPa.). The installation

of this appliance must conform with local codes or, in the absence of local codes, with the National Fuel Gas

Code, ANSI Z223.1. Installation in Canada must be in accordance with the Standard Can1-b149.1 and/or .2

(installation code for gas burning appliances and

equipment) and local codes.

NATURAL GAS HOOK UP: (THIS TYPE OF CON-

NECTION SHOULD BE PERFORMED BY A CERTIFIED OR

LICENSED TECHNICIAN ONLY.)

Connection: 1/2" NPT male with 3/8" flare adapter.

Operating pressure: 4.0" W.C. Supply pressure: 5" to 14"

w

a

t

er column. If in excess of 14" W.C., a step down

regulator is required. Check with your local gas utility

company or local codes for instructions on installing gas

supply lines. Be sure to check on type and size of run,

and how deep to bury the line. If the gas line is too small,

the grill will not function properly. Any joint sealant used

must be an approved type and be resistive to the actions

of LP gases.

TO HOOK-UP THE FITTINGS SUPPLIED WITH

THE GRILL:

Assemble as shown (Fig. 08). Use threading compound on

male threads only. Do not use threading compound on

the male end of the 1/2 NPT to 3/8 flare adapter. Use a

second pipe wrench to hold the grill inlet pipe to avoid

shifting any internal gas lines of the grill. Ensure that the

regulator arrow points in the direction of gas flow towards

the unit, away from the supply. Do not forget to place the installer-supplied gas valve in an accessible location.

LP GAS HOOK UP (TYPE 1 OR QCC1 REGULATOR):

Grills orificed for use with LP gas come equipped with a high capacity hose/regulator assembly for connection to

a standard 20 lb

. LP cylinder (Type 1). The LP tank is not included.

*Installation must conform with

local codes or with the National

Fuel Gas Code ANSI Z223.1 or

the CAN/CGA-B149.2 Propane

Installation Code

Coupling

1/2” NPT x

2.0”

NIpple

Regulator

4.0" W.C.

Adapter 1/2”NPT

to 3/8”flare fitting

Do not put threading

compound on these

threads

Bottom of unit

Threading compound

must be resistant to LP gas

1/2” NPT x 5.0"

Nipple

Installer supplied shut-off

valve must be easily

accessible*

FIG. 08 Natural Gas

INSTALLATION

GAS HOOK-UP

13

Connection: 1/2" NPT male with a 3/8" Flare adapter (included). LP Hose with a quick disconnect and fittings are

included. Operating pressure: 11.0" W.C.

CAUTION!

Before connecting LP tank to regulator, check that all grill burners and side burners, smokers, and rotisserie valves

are in the OFF position and open grill lid.

To connect the LP regulator/hose assembly to the tank/valve assembly, first make sure the main valve on the

tank is completely closed. Although the flow of gas is stopped when the Type 1 system is disconnected as part

of of its safety feature, you should always turn off the LP tank main valve (Fig. 09) after each use and during

transport of the tank or unit. Insert the regulator inlet into the tank valve and turn to the black coupler

clockwise until the coupler tightens up.

Do not overtighten the coupler. Turn the main tank valve on and turn

the burner control valves on the unit to the “HI” position for about 20 seconds to allow the air in the system to

purge, turn valves off and wait 5 minutes before attempting to light the burners.

To disconnect the coupler, first make sure the main tank valve is turned off. Grasp the coupler and turn counter

clockwise. The inlet will then disengage. Remove the inlet from the tank valve opening if it has not already

done so when it disengaged. Your local LP filling station should be equipped with the proper equipment to fill

your tank.

LP TANK REQUIREMENTS:

A dented or rusty LP tank may be hazardous and should be checked by your LP supplier. The cylinder that is

used must have a collar to protect the cylinder valve. Never use a cylinder with a damaged valve. Always

check for leaks after every LP tank change. The LP gas cylinder must be constructed and marked in accordance

with the specifications for LP gas cylinders of the U.S. Department of Transportation (DOT or CAN/CSA-B339)

and designed for use with a Type 1 system only. Do not change the regulator/hose assembly from that supplied

with the unit or attempt to use a Type 1 equipped regulator/hose assembly with a standard 510 POL tank/valve

assembly. The cylinder must be provided with a shut-off valve terminating in an LP gas supply cylinder valve

outlet specified, as applicable, for connection Type 1.

If the appliance is stored indoors, the cylinder must be

disconnected and removed from the appliance. Cylinders must be stored outdoors in a well-ventilated area

out of the reach of children.

Note:

When an LP unit is being directly connected to an LP house system, you must follow the natural gas hook up guidelines.

The installer must provide the proper gas regulator to reduce the gas flow to 11” W.C.

Note:

The Grill comes with the LP Regulator/Hose assembly installed at the factory. The assembly, along with the entire Grill

system, is leak tested. Do not remove the Regulator/Hose

assembly from the Grill during installation.

WARNING :

1. Do not remove the Grill from the pallet until you are

r

eady to install.

2. Do not place the Grill directly on the ground or any other

flat surface without support. This will prevent damaging

the r

egula

t

or/hose assembly by the weight of the grill.

3. Check the hose

, r

egula

t

or and c

onnec

t

ors f

or damage

.

Look for cracks, abrasions, brittleness, holes, dents and

nicks.

4. Do not attempt to remove, repair, or replace the

Regulator/Hose assembly by yourself. It must be done

by a qualified licensed technician only.

FIG. 09 LP G

as

INSTALLATION

GAS HOOK-UP

Bottom of unit

Elbow 45

º

1/2” female

NPT x 3/8” male flare

(installed on the unit)

LP Regulator hose

assembly 11" W.C.

Type 1 Regulator

Main Tank Valve

20 lb. LP Tank

*Installation must conform with

local codes or with the National

Fuel G as Code ANSI Z223.1 or the

CAN/CGA-B149.2 Propane

Installation Code

14

INSTALLATION

GAS HOOK-UP

LP TANK RESTRAINT FOR BUILT-IN INSTALLATION

If the grill is to be installed in a Built-in application, then the grill must be installed in accordance with the

B

uilt–in installation guidelines.

If you intend to operate your Built-in grill on LP gas utilizing a 20 lb Type 1 cylinder, then the Built-in LP tank

r

estraint must be installed prior to initial use of the grill. If you do not have one please contact DCS Customer

Care at (888) 936-7872 for information on obtaining one.

The following steps will illustrate how to properly locate and install the LP tank restraint within the Built-in

enclosure.

NOTE:

The grill comes with the LP Regulator/Hose assembly installed at the factory. The assembly, along with the entire grill

system, is leak tested.

Do not remove the Regulator/Hose assembly from the grill during installation.

FIG. 10

18” max.

The maximum distance from the center

of the manifold cut out to the center of

the tank restraint is

18 inches.

C

enter of manifold

cut out projected to

floor of the island.

C

ent

er of

T

ank Restraint must be

plac

ed within this ar

ea to avoid

causing stress on the LP regulator

hose c

onnec

tion.

15

STEP 1

Place the tank restraint in the island (Fig. 11).

STEP 2

Locate the tank restraint in the island within the recommended area

(Fig. 10 and 12).

STEP 3

Once located, secure to the bottom of the island using all eight hole

locations provided on the restraint. Wood screws can be used for

wooden floors or 1/4 inch diameter anchor screws or bolts may be

used if the floor is concrete or masonry (Fig. 13).

STEP 4

W

hen secure, place the LP cylinder into the tank restraint making

sure to seat the tank all the way down, securely affixing the tank in

the restraint (Fig. 14).

STEP 5

Attach the regulator hose assembly and operate the grill normally as

described in the Use and Care manual (Fig. 15).

INSTALLATION

GAS HOOK-UP

FIG. 15

FIG. 11

FIG. 12

FIG. 13

FIG. 14

16

GENERAL:

A

lthough all gas connections on the grill are leak tested at the factory prior to shipment, a complete gas

tightness check must be performed at the installation site due to possible mishandling in shipment, or excessive

pressure unknowingly being applied to the unit. Periodically check the whole system for leaks, or immediately

check if the smell of gas is detected.

Before Testing:

Do not smoke while leak testing. Extinguish all open flames. Never leak test with an open flame. Make a

soap solution of one part liquid detergent and one part water. You will need a spray bottle, brush, or rag to

apply the solution to the fittings. For LP units, check with a full cylinder. The valve panel must be removed to

check the valves and fittings. Remove the knobs and the safety valve knob, then remove the 2 screws which

fasten the valve panel to the unit (you will need a Philips screw driver for this). Pull the valve panel outward and

unplug the wires from the ignition module and the back of the ignition button. In the back of the unit remove

the scr

ews which hold the service panel in place. Remove the service panel.

To Test:

Make sure all control valves are in the “OFF” position. Turn the gas supply “ON”. Check all connections from the

supply line, or LP cylinder up to and including the manifold pipe assembly. Apply the soap solution around the

connection, valve, tubing and end of the manifold. Soap bubbles will appear where a leak is present. If a leak is

present, immediately turn off gas supply, tighten any leaking connections, turn gas on, and recheck. Check all

the gas connections at the base of the control valves where they screw into the manifold pipe.

To check rotisserie burner and safety valve the burner must be lit, then leak test the connections located behind

the service panel. If you cannot stop a gas leak turn off the gas supply and call your local gas utility, or the

dealer you purchased the appliance from. Only those parts recommended by the manufacturer should be used

on the grill. Substitution can void the warranty.

WARNING!

Do not use the g

rill until all connections have been checked and do not leak.

Check all gas supply fittings for leaks before each use. Keep a spray bottle of soapy water near the gas supply

shut-off valve. Spray all the fittings. Bubbles indicate leaks (Fig. 16 & 17).

Bottom of unit

CHECK HOSE FOR

SIGNS OF ABRASIONS,

CRACKS, OR LEAKS

LEAK TEST POINTS

LP TANK

Bottom of unit

LEAK TEST POINTS

INSTALLATION

LEAK TESTING

FIG. 16 LP G

as

FIG. 17 Nat. Gas

GRILL BURNER AIR ADJUSTMENT:

Each grill burner is tested and adjusted at the factory prior to shipment; however, variations in the local gas

supply or a conversion from one gas to another may make it necessary to adjust the burners. The flames of the

burners (except the rotisserie burner) should be visually checked and compared to that of the drawing in Fig.18.

F

lames should be blue and stable with no yellow tips (LP units may have some yellow tipping), excessive noise or

lifting. If any of these conditions exist, check if the air shutter or burner ports are blocked by dirt, debris, spider

webs, etc. Proceed with air shutter adjustment. The amount of air which enters a burner is governed by a metal

cup at the inlet of the burner called an air shutter. It is locked in place by a screw which must be loosened prior

to lighting the burner for adjustment.

GRILL BURNER FLAME HEIGHT:

Before beginning, ensure the grill is OFF and cool. To access the grill

burner air shutters, first remove the grates and radiants from the fire-

box, then remove the grill burner using instructions shown on page 29,

Fig. 46. With a screw driver, loosen the lock screw on the face of the air

shutter slightly so that the air shutter can be adjusted.

To Adjust:

1. Be careful as the burner may be very hot.

2. If the flame is yellow, indicating insufficient air, turn the air shutter

counterclockwise to allow more air to the burner.

3. If the flame is noisy and tends to lift away from the burner, indicating too much air, turn the air shutter

clockwise.

Reinstall the U-burner, ensuring the burner is level. Light the burner and check the flame. If all is okay, remove

the burner (CAUTION - burner may be hot, allow time to cool) and tighten the air shutter screw. If not repeat the

above procedure to readjust the air shutter.

LOW FLAME SETTING ADJUSTMENT:

The valves on the grill feature an adjustable low setting. Due to fluctuations in gas pressure, heating value or

gas conversion, you may feel it necessary to increase or decrease gas flow in the low position. We do not

recommend adjusting the infrared rotisserie burner.

To Adjust:

1. Light the burner.

2. Turn the control knob to the lowest setting (all the way counter-clockwise).

3. Remove the knob.

4. While holding the valve shaft with pliers, insert a thin, flat tipped screwdriver into the

shaft and while viewing the burner adjust to a minimum stable flame (Fig. 19).

SIDE BURNER FLAME HEIGHT:

The correct height of the flame mainly depends on the size of the bottom of the

cooking utensil, the material of the cooking utensil, the amount and type of food and

the amount of liquid in the utensil. Following are some basic rules for selecting flame

height.

■

F

or safety reasons the flame must never extend beyond the bottom of the cooking

utensil. Never allow flames to curl up the side of the pan (see Fig. 20).

■

Utensils which conduct heat slowly (such as glass-ceramic) should be used with medium to low flames. If you

are cooking with a large amount of liquid, a slightly larger flame can be used.

WARNING: IMPORTANT!

Before lighting, inspect the gas supply piping or hose prior to turning the gas "on". If there is evidence of cuts, wear,

or abrasion, it must be replaced prior to use.

1-1/2"

3

/8"

FIG. 18 Burner Flame

Height

FIG. 19 L

o

w Setting Adjustment

INSTALLATION

BURNER ADJUSTMENT

Fig. 20

Proper Flame Height

OPEN

CLOSE

17

18

RADIANT ASSSEMBLY INSTALLATION:

1

.

Unpack ceramic rods and remove radiant (Fig. 21) from the unit.

2

.

Unlock radiant end cap by pushing it up with two fingers (Fig. 22).

3.

Place 18 ceramic rods on the radiant (Fig. 23).

4.

Lock radiant end cap (Fig. 24).

5.

Place the assembled radiant in the unit (Fig. 25).

Note:

In c

ase a c

er

amic r

od breaks:

a) Unlock radiant end cap by pushing it up with two fingers (Fig. 16) or pliers may be used.

b) Replace broken ceramic rod.

c) Lock radiant end cap.

INSTALLATION

RADIANT ASSEMBLY

FIG. 21

FIG. 22

FIG. 23

FIG. 24

FIG. 25

19

NOTE:

If any of the listed items are missing, contact DCS at (888) 936-7872. Please be prepared with your

Model #, Serial # and description of item(s) that are missing.

Read all installation instructions in this manual to see if the unit has been properly installed. If not done or

done correctly, correct before using the unit.

❏ Specified clearances

m

aintained to

combustibles.

❏ Verified proper enclosure

ventilation.

❏ All internal packaging

removed.

❏ Removed shipping

brackets

❏ Knobs turn freely, bezels

centered.

❏ Each burner lights

satisfactorily, individually

or with adjacent burner

lit.

❏ Air shutters adjusted.

❏ Low flame setting

s

atisfactory.

❏ D

rip pan in place properly

and sliding freely.

❏ Pressure regulator

connected and set for 4.0"

W.C. Natural, 11.0" W.C. LP

gas.

❏ Manual shut-off valve

installed and accessible.

❏ Unit tested and free of

leaks.

❏ User informed of gas

s

upply shut-off valve

location.

❏ All radiants are assembled

and put in place.

❏ Check match lighting.

■

PLEASE LEAVE THESE

INSTRUCTIONS WITH THE

USER.

■

USER, PLEASE RETAIN

THESE INSTRUCTIONS

FOR FUTURE REFERENCE.

INSTALLATION

INSTALLER CHECKLIST

Tag location of

Model # and Serial #

20

TO LIGHT THE GRILL BURNER:

O

pen the grill lid and/or remove the top grate cover from side burner (for 48BQR) before lighting. Turn all knobs

to “OFF”. Turn the main gas supply on slowly. If you smell gas, shut off gas supply and call for service.

P

ush and hold the ignition button, turn the selected burner knob to “SEAR”. If burner does not light in 4 to 5

seconds, turn knob “OFF” and wait 5 minutes before trying again for any accumulated gas to dissipate.

Grill Match Lighting:

If the burner will not light after several attempts then the burner

can be match lit. If you’ve just attempted to light the burner with

the ignition, allow 5 minutes for any accumulated gas to dissipate.

Keep your face as far away from the grill as possible and hold and

pass a lit, paper book match over the hole located on the top left

for burner on the left, or the right hole for the right burner (Fig. 26

& Fig. 27). Push and turn the control knob which is centered on

the burner where the lit match is located, to “SEAR/HI”. If the

bur

ner does not light in 4 seconds, turn the knob off, wait 5 minutes and try again.

Onc

e the left or right burner is lit, the adjacent burner can be lit by the cross-lighting method. For center

burners to cross light, light the adjacent far left or right burner using the standard or match light procedure.

Push and turn the control knob for the desired center burner to “HI”. The gas will be ignited by the adjacent

burners flame. If the burner does not light in 4 seconds, turn knob off, wait 5 minutes and try again.

NOTE:

Improper lighting procedures can cause the LP tank flow control to activate,

resulting in reduced heat output. If this is suspected, to reset flow control,

shut off all burner controls and LP cylinder valve, wait 30 seconds, then turn

LP cylinder valve on extremely slowly, wait five (5) seconds and push and

hold the ignition button and turn burner valve on to “SEAR”.

TO LIGHT DUAL SIDE BURNERS (48BQR MODELS ONLY):

CAUTION!

T

he side burner c

over may be hot if the grill burners are in operation.

Side Burners Lighting Instructions:

First remove the burner cover and any cooking utensils from the burner

grate. Push and hold the ignition button, turn the control knob to the “HI”

position until the burner is lit or 4 seconds pass. If the burner doesn’t ignite,

wait 5 minutes for any accumulated gas to dissipate then try again. If the

burner will not light after several attempts, check the trouble shooting

instructions on page 31.

Side Burners Match Lighting:

Hold a lit paper book mat

ch near the burner ports

, tur

n the c

ontrol knob

counterclockwise to “HI”. Move your hand immediately once the burner is lit. Rotate

the c

ontrol knob to the desired setting.

Note:

If you are using propane gas, a slight pop or flash may occur at the burner ports a few

seconds after the burner has been turned “off”. This “extinction pop” is normal for

propane gas.

Side burners:

Your side bur

ner is equipped with bur

ners t

ypical of those used in r

estaur

an

ts

. These burners are designed for

maximum cleanability and controlability. The burner should never be operated if the cap is not in place (Fig. 29).

USING THE GRILL

LIGHTING INSTRUCTIONS

FIG. 26

FIG. 27

FIG. 28

I

GNITION

FIG. 29

Cap

Ignition

Control Knobs

SEAR

O

FF

All knobs must be in the OFF position before

opening LP tank valve.

Now open the LP tank valve two (2) full

turns min.

Failure to follow the steps in the order shown may cause the Flow

L

imiting Device to ac tivate resulting in ex tremely low gas ow and

improper operation.

A

ttach regulator hose assembly to tank.

WARNING

3

1

2

Page is loading ...

DCS BGB48-BQR User manual

DCS BGB48-BQR User manual

in other languages

Related papers

Other documents