Epson BrightLink 455Wi Installation guide

BrightLink 455Wi

Installation Guide

Guide d’installation

TM

2

Safety Instructions

For your safety, read all the instructions in this guide before using the setting plate. Incorrect handling that

ignores instructions in this guide could damage the setting plate or could result in personal injury or property

damage. Keep this installation guide at hand for future reference.

Read the safety instructions in the User's Guide for your projector and follow the instructions in this

document.

Explanation of Symbols

The warning marks shown below are used throughout this installation guide to prevent personal injury or

property damage. Make sure you understand these warnings when reading this installation guide.

Safety Precautions for Installation

This symbol indicates information that, if ignored, could possibly result in personal injury or even death

due to incorrect handling.

This symbol indicates information that, if ignored, could possibly result in personal injury or physical

damage due to incorrect handling.

Symbol indicating an action that must not be done

Symbol indicating an action that should be done

The setting plate is designed specifically for mounting a projector to a wall. If anything other than a

projector is mounted, the weight may result in damage.

If the setting plate falls, it could cause personal injury or property damage.

The installation work (wall mounting) should be performed by specialists who have technical knowledge

and ability. Incomplete or incorrect installation could cause the setting plate to fall and cause personal

injury or property damage. Contact the customer support office listed in “Where to Get Help” in the User's

Guide for your projector when installing the setting plate.

Follow the instructions in this guide when installing the setting plate.

If the instructions are not followed, the setting plate may fall, resulting in personal injury or property damage.

Handle the power cable carefully.

Incorrect handling may cause fire or electric shock. Observe the following precautions when handling:

• Do not handle the power plug with wet hands.

• Do not use a power cable that is damaged or modified.

• Do not pull the power cable with too much force when routing the cable through the setting plate.

When you mount the projector on the wall with the setting plate, the wall requires enough strength to hold

the projector and the setting plate. Confirm the weight of the projector and the setting plate before

installation, and maintain the strength of the wall. If the wall is not strong enough, reinforce the wall

before installation.

Do not install the setting plate in a place where it might be subjected to vibration or shock.

Vibration or shock could cause damage to the projector or mounting surface. It could also cause the setting plate or

projector to fall and cause personal injury or property damage.

Install the setting plate so that it can sufficiently support the weight of the projector and setting plate, and

resist any horizontal vibration. Use M8 nuts and bolts.

Nuts and bolts smaller than M8 could cause the setting plate to fall. Epson takes no responsibility for any damage or

injury caused by incorrect installation.

Warning

Caution

Warning

3

English

Location

• Before installing the projector, verify the power supply wiring for the installation location.

• Install the projector away from other electric devices such as fluorescent lights or air conditioners. Some

kinds of fluorescent lights could interfere with the remote control of the projector.

• Install the projector away from direct sunlight and other bright light sources.

• It is recommended to keep connection cable length less than 65 ft (20 meters) to reduce external noise.

• Install the setting plate in a place free from excessive dust and humidity to prevent the lens or optical

components from becoming dirty.

About This Installation Guide

This guide describes how to mount the BrightLink™ 455 Wi projector to a wall using the exclusive setting

plate.

The installation work should be performed by at least two qualified service personnel. If you need to

loosen any screws during installation, be careful not to drop the setting plate.

If the setting plate or projector falls, it could cause personal injury or property damage.

Inspect the setting plate on a regular basis to ensure there are no broken parts or loose screws.

If there are any broken parts, stop using the setting plate immediately. If the setting plate or projector falls, it could cause

personal injury or property damage.

Never modify the setting plate.

Do not hang on the setting plate or hang a heavy object on the setting plate.

If the projector or setting plate falls, it could cause personal injury or property damage.

If you use adhesives to prevent the screws from loosening or things such as lubricants or oils on the slide

plate fixing part of the projector, the case may crack and cause the projector to fall, resulting in personal

injury or property damage. Do not use adhesives, lubricants, or oils to install or adjust the setting plate.

Tighten all screws firmly after adjustment.

If the screws are not tightened firmly, the projector or setting plate may fall and cause personal injury or property

damage.

Never loosen the bolts and nuts after installation.

Confirm that the screws have not become loose on a regular basis. If you find any loose screws, tighten them firmly. If the

screws are not tightened firmly, the projector or setting plate may fall and cause personal injury or property damage.

Do not install the setting plate in a location where the operating temperature for your projector model

may be exceeded.

Such an environment may damage the projector.

Install the setting plate in a place free from excessive dust and humidity to prevent the lens or optical

components from becoming dirty.

Do not use excessive force when adjusting the setting plate.

The setting plate may break, resulting in personal injury.

Warning

Caution

4

1 Package Contents

s Page 5

2 Specifications

s Page 7

3 Connecting Devices

s Page 8

4 Positioning the Projector

s Page 9

(1) Installation worksheet for projecting on a pre-installed wall-

mounted board

(2) Installation worksheet for projecting on a plain wall

(3) Installation measurements in inches

(4) Installation measurements in millimeters

5 Installing the Projector

s Page 17

(1) Install the wall plate on the wall

(2) Determine the projection distance and pull out the slider

(3) Attach the setting plate to the wall plate

(4) Secure the projector to the setting plate

(5) Connect the power cable and other cables to the projector

6 Adjusting the Image

s Page 21

(1) Turn on the projector

(2) Display the test pattern

(3) Change the aspect ratio if necessary

(4) Adjust the focus

(5) Use the left adjustment dial to adjust the horizontal roll

(6) Use the right adjustment dial to adjust the horizontal rotation

(7) Use the top adjustment dial to adjust the vertical tilt

(8) Adjust the vertical position

(9) Adjust the forward/backward slide

(10) Turn off the display of the test pattern or computer image

7 Attaching the Covers

s Page 26

(1) Attach the wall plate cover and end cap

(2) Attach the cable cover to the projector

5

English

1. Package Contents

Mounting hardware

• Use the bolts supplied with the setting plate to install it, as directed in this guide. Do not substitute these

bolts with any other types.

• Use commercially available M8 x 50 mm anchors (at least 3) or 8 x 80 mm lag bolts (at least 3) to attach the

wall plate to the wall.

• Gather the tools and parts you need before you begin installation.

Shape Name Quantity Application

M8 x 15 mm hexagon socket head cap bolt with

washer

2 For installing setting plate

M5 x 12 mm hexagon socket head cap bolt with

washer

2 For securing projector

M4 x 12 mm hexagon socket head cap bolt without

washer

2 For installing wall plate cover

Hexagon wrenches (for M4, M5, and M8)

Wall plate cover

Setting plate (wall mount)

Template sheet

(for installing the wall plate)

End cap

Wall plate

6

Projector box

Interactive pens and

AAA batteries

Power cord

Projector

Epson Projector

S

oftware for Easy

Interactive Function CD

VGA computer cable

Remote control

and AA batteries

USB cable

Epson Projector

Software CD

Security sticker

BrightLink

455Wi CD

Pen tray

Battery charger with 4 AAA

rechargeable batteries

(for interactive pens)

TeamBoard Draw CD

7

English

2. Specifications

Wall plate

Setting plate adjustment range

Item Specification Remark Reference Page

Setting plate weight Approx. 13.89 lb

(6.3 kg)

Wall plate 4.85 lb (2.2 kg)

Covers and cap 1.04 lb (0.47 kg)

Forward/backward slide

adjustment range

0 to 11.81 in.

(300 mm)

Refer to the figure

below

Vertical slide adjustment range 4 ° Minimum: 1.10 in. (28 mm)

Maximum: 1.67 in. (42.5 mm)

s 25

Vertical tilt adjustment range ± 5 ° Fine adjustments possible with adjustment dial

s 24

Horizontal rotation adjustment

range

± 5 ° Fine adjustments possible with adjustment dial

s 24

Horizontal roll adjustment range ± 3 ° Fine adjustments possible with adjustment dial

s 23

Horizontal slide adjustment range ± 1.77 in.

(45 mm)

Refer to the figure

below

[Unit: in. (mm)]

9.87 (250)

17.97 (456)

9.05 (230)

8.74 (222)

6.3 (160)

9.71 (247)

0.59 (15)

4.4 (112)

8 (203.2)

3.0

(76)

1.8 (46)

4.75

(121)

1.81 (46)

Forward/backward slide adjustment range:

0 to 11.81 in. (300 mm)

Horizontal slide adjustment range:

± 1.77 in. (45 mm)

8

3. Connecting Devices

Make sure you have the power cable, computer cable, USB cable, and other parts at the location where the

setting plate is to be installed.

Make sure you have all necessary cables for any devices, such as a document camera or microphone, that you

will connect to the projector.

External speakers

LAN device

Microphone

USB cable

(for Easy Interactive Function)

Document camera

Computer

Computer cable

(for computer video output)

Connection Example

Dedicated USB cable

(supplied with document camera)

Audio cable

(commercially available product)

LAN cable

Power cord

9

English

4. Positioning the Projector

The BrightLink 455Wi can project up to 96 inches diagonally for a WXGA image or 85 inches diagonally for an

XGA image. You can project onto a pre-installed whiteboard or directly onto a plain wall. The height of the

included wall mount determines the maximum image size and how high the image appears on the wall or

whiteboard. The distance of the projector from the wall (once it is mounted on the adjustable arm of the

setting plate) also affects image size and position.

If you are planning to project on a whiteboard, the image may not fill the entire board, depending on the

aspect ratio. If you match the image height to the board’s height, gaps may appear on the sides of the board.

Use the following worksheets to determine the proper location of the wall plate on the wall. If you are

projecting onto a pre-installed whiteboard, use the worksheet below. If you are projecting on a plain wall, use

the worksheet on page 10.

Installation worksheet for projecting on a pre-installed wall-mounted

board

(1) Measure the ceiling height (distance from the floor to the ceiling).

(2) Measure the height of the board’s image area (h).

(3) Measure the width of the board’s image area (w).

(4) Measure the distance from the floor to the bottom of the board’s

image area (f).

(5) Measure the distance from the ceiling to the top of the board’s image area (c).

(6) Measure the thickness of the board (x).

_____

_____ (h)

_____ (w)

_____ (f)

_____ (c)

_____ (x)

10 in. (254 mm)—height of

wall plate plus cover

Required distance from top

of image area to wall plate (b)

Diagonal size of

image area (S)

Height of

image area (h)

Distance from ceiling to

top of image area (c)

Width of image area (w)

Distance from floor to

bottom of image area (f)

10

(7) Determine the aspect ratio of the board or of the images that will be

projected. For new computers or laptops, this will most likely be WXGA

(16:10). For older equipment, this will most likely be XGA (4:3). You may need

to consult your IT director for this information.

4:3 XGA 16:10 WXGA 16:9 Widescreen

(8) Using the tables on pages 12 to 15 for your aspect ratio and desired image

height (h), find the required distance between the top of the image area and

the wall plate (b).

(9) Determine the position for your projector installation by adding the values for

(f), (h), and (b), plus an additional 10 inches for the height of the wall plate

plus the cover.

If the ceiling height of your room (as noted in step 1) does not meet the

minimum ceiling height required for your board, you may need to select a

smaller image size or move the board to a lower position on the wall.

(10)After confirming your image size, use tape or a pencil to mark the distance (b)

from the top of the image area on the board to the bottom of the wall plate.

(11)Align the line (horizontal) on the template sheet with the (b) mark, then

align the center line on the template sheet with the center of the image area.

Follow the instructions on page 17 to install the projector.

Installation worksheet for projecting on a plain wall

(1) Measure the ceiling height (distance from the floor to the ceiling).

(2) Determine the desired aspect ratio of the image. For new computers or

laptops, this will most likely be WXGA (16:10). For older equipment, this will

most likely be XGA (4:3). You may need to consult your IT director for this

information.

4:3 XGA 16:10 WXGA 16:9 Widescreen

(3) Using the tables on pages 12 to 15 for your aspect ratio, select the largest

image size available for your ceiling height.

Image height (h)

Image width (w)

(4) Determine the desired distance from the floor to the bottom of the image

area (f).

The recommended minimum distance is 30 inches. Images appearing less

than 28 inches from the floor may be obstructed for some viewers.

(5) Find the top of the projected image area by adding distances (f) and (h).

(6) Use the tables on pages 12 to 15 to determine the required distance from the

top of the image area to the bottom of the wall plate (b).

(7) Add:

Required distance from top of image area to wall plate (b)

Height of image area (h)

Distance from floor to bottom of image area (f)

Height of wall plate plus cover

If the total exceeds the ceiling height, you will need to reduce the image size

or reduce the distance from the floor to the bottom of the image area.

_____ (b)

_____ (f)

_____ (h)

_____ (b)

+10

inches

_____ total

_____

_____ (h)

_____ (w)

_____ (f)

_____

_____ (b)

_____ (h)

_____ (f)

+10

inches

_____ total

11

English

(8) After confirming your image size, use tape or a pencil to mark the distance (b) from the top of

the image area on the board to the bottom of the wall plate.

(9) Align the line (horizontal) on the template sheet with the (b) mark, then align the center

line on the template sheet with the center of the image area. Follow the instructions on page

17 to install the projector.

The tables on the following pages provide installation information for all supported image sizes. The

minimum ceiling height is based on an image 30 inches from the floor; if the image is lower, the minimum

ceiling height is reduced by the corresponding measurement.

Use the worksheets, the illustration below, and the information in the tables on the following pages to

determine the projection distance and placement of the wall plate. The recommended range for projection

distance (a) is 2.76 to 14.57 inches (7 to 37 cm).

10 in. (254 mm) —height

of wall plate plus cover

Required distance from top

of image area to wall plate (b)

Diagonal image

size (S)

Ceiling

height

Distance from ceiling to

top of image area (c)

Width of image area (w)

Distance from floor to

bottom of image area (f)

Height of

image area (h)

Wall plate

Projection surface

Offset value for the position of

the center of the screen and the

center of the wall plate

Distance from wall of projection

surface or whiteboard

2.55 in. (65 mm)

10 in. (254 mm)

Line on template

12

Installation measurements in inches

Diagonal

image

size

(S)

16:10 WXGA 4:3 XGA 16:9 Widescreen

Min.

ceiling

height*

Image

width

(w)

Image

height

(h)

Min.

projection

distance

(a)

Distance

from top

of image

to wall

plate (b)

Min.

ceiling

height*

Image

width

(w)

Image

height

(h)

Min.

projection

distance

(a)

Distance

from top

of image

to wall

plate (b)

Min.

ceiling

height*

Image

width

(w)

Image

height

(h)

Min.

Projection

distance

(a)

Distance

from top

of image

to wall

plate (b)

55”

— — — — — 83.8 44.0 33.0 3.7 10.8 — — — — —

56”

— — — — — 84.6 44.8 33.6 4.1 11.0 — — — — —

57”

— — — — — 85.4 45.6 34.2 4.4 11.2 — — — — —

58”

— — — — — 86.2 46.4 34.8 4.8 11.4 — — — — —

59”

81.6 50.0 31.3 2.7 10.3 86.9 47.2 35.4 5.2 11.5 — — — — —

60”

82.3 50.9 31.8 3.0 10.5 87.7 48.0 36.0 5.5 11.7 81.8 52.3 29.4 3.5 12.4

61”

83.0 51.7 32.3 3.3 10.6 88.5 48.8 36.6 5.9 11.9 82.5 53.2 29.9 3.9 12.6

62”

83.7 52.6 32.9 3.6 10.8 89.3 49.6 37.2 6.2 12.1 83.1 54.0 30.4 4.2 12.8

63”

84.3 53.4 33.4 4.0 11.0 90.0 50.4 37.8 6.6 12.2 83.8 54.9 30.9 4.5 12.9

64”

85.0 54.3 33.9 4.4 11.1 90.8 51.2 38.4 7.0 12.4 84.5 55.8 31.4 4.8 13.1

65”

85.7 55.1 34.4 4.6 11.3 91.6 52.0 39.0 7.3 12.6 85.2 56.7 31.9 5.2 13.3

66”

86.4 56.0 35.0 4.9 11.4 92.4 52.8 39.6 7.7 12.8 85.9 57.5 32.4 5.5 13.5

67”

87.1 56.8 35.5 5.2 11.6 93.1 53.6 40.2 8.0 12.9 86.5 58.4 32.8 5.8 13.7

68”

87.8 57.7 36.0 5.5 11.7 93.9 54.4 40.8 8.4 13.1 87.2 59.3 33.3 6.2 13.9

69”

88.4 58.5 36.6 5.9 11.9 94.7 55.2 41.4 8.8 13.3 87.9 60.1 33.8 6.5 14.1

70”

89.1 59.4 37.1 6.2 12.0 95.5 56.0 42.0 9.1 13.5 88.6 61.0 34.3 6.8 14.2

71”

89.8 60.2 37.6 6.5 12.2 96.2 56.8 42.6 9.5 13.6 89.2 61.9 34.8 7.2 14.4

72”

90.5 61.1 38.2 6.8 12.3 97.0 57.6 43.2 9.8 13.8 89.9 62.8 35.3 7.5 14.6

73”

91.2 61.9 38.7 7.1 12.5 97.8 58.4 43.8 10.2 14.0 90.6 63.6 35.8 7.8 14.8

74”

91.9 62.8 39.2 7.5 12.7 98.6 59.2 44.4 10.6 14.2 91.3 64.5 36.3 8.1 15.0

75”

92.6 63.6 39.7 7.8 12.8 99.3 60.0 45.0 10.9 14.3 91.9 65.4 36.8 8.4 15.2

76”

93.2 64.4 40.3 8.1 13.0 100.1 60.8 45.6 11.3 14.5 92.6 66.2 37.3 8.8 15.4

13

English

* Based on an image 30 inches from the floor; if the image is lower, the minimum ceiling height is reduced by the corresponding measurement.

77”

93.9 65.3 40.8 8.4 13.1 100.9 61.6 46.2 11.7 14.7 93.3 67.1 37.8 9.1 15.5

78”

94.6 66.1 41.3 8.7 13.3 101.7 62.4 46.8 12.0 14.9 94.0 68.0 38.2 9.4 15.7

79”

95.3 67.0 41.9 9.0 13.4 102.4 63.2 47.4 12.4 15.0 94.6 68.9 38.7 9.7 15.9

80”

96.0 67.8 42.4 9.4 13.6 103.2 64.0 48.0 12.7 15.2 95.3 69.7 39.2 10.1 16.1

81”

96.7 68.7 42.9 9.7 13.7 104.0 64.8 48.6 13.1 15.4 96.0 70.6 39.7 10.4 16.3

82”

97.3 69.5 43.5 10.0 13.9 104.8 65.6 49.2 13.5 15.6 96.7 71.5 40.2 10.7 16.5

83”

98.0 70.4 44.0 10.3 14.0 105.5 66.4 49.8 13.8 15.7 97.4 72.3 40.7 11.1 16.7

84”

98.7 71.2 44.5 10.6 14.2 106.3 67.2 50.4 14.2 15.9 98.0 73.2 41.2 11.4 16.9

85”

99.4 72.1 45.0 11.0 14.4 107.1 68.0 51.0 14.5 16.1 98.7 74.1

41.7

11.7 17.0

86”

100.1 72.9 45.6 11.3 14.5 — — — — — 99.4 75.0

42.2

12.0 17.2

87”

100.8 73.8 46.1 11.6 14.7 — — — — — 100.1 75.8

42.7

12.4 17.4

88”

101.5 74.6 46.6 11.9 14.8 — — — — — 100.7 76.7

43.1

12.7 17.6

89”

102.1 75.5 47.2 12.2 14.9 — — — — — 101.4 77.6

43.6

13.0 17.9

90”

102.8 76.3 47.7 12.6 15.1 — — — — — 102.1 78.4

44.1

13.3 18.0

91”

103.5 77.2 48.2 12.9 15.3 — — — — — 102.8 79.3

44.6

13.7 18.2

92”

104.2 78.0 48.8 13.2 15.4 — — — — — 103.4 80.2 45.1 14.0 18.3

93”

104.9 78.9 49.3 13.5 15.6 — — — — — 104.1 81.1 45.6 14.3 18.5

94”

105.6 79.7 49.8 13.8 15.8 — — — — — — — — — —

95”

106.3 80.6 50.3 14.2 15.9 — — — — — — — — — —

96”

106.9 81.4 50.9 14.5 16.1 — — — — — — — — — —

Diagonal

image

size

(S)

16:10 WXGA 4:3 XGA 16:9 Widescreen

Min.

ceiling

height*

Image

width

(w)

Image

height

(h)

Min.

projection

distance

(a)

Distance

from top

of image

to wall

plate (b)

Min.

ceiling

height*

Image

width

(w)

Image

height

(h)

Min.

projection

distance

(a)

Distance

from top

of image

to wall

plate (b)

Min.

ceiling

height*

Image

width

(w)

Image

height

(h)

Min.

Projection

distance

(a)

Distance

from top

of image

to wall

plate (b)

14

Installation measurements in millimeters

Diagonal

image

size

(S)

16:10 WXGA 4:3 XGA 16:9 Widescreen

Min.

ceiling

height*

Image

width

(w)

Image

height

(h)

Min.

projection

distance

(a)

Distance

from top

of image

to wall

plate (b)

Min.

ceiling

height*

Image

width

(w)

Image

height

(h)

Min.

projection

distance

(a)

Distance

from top

of image

to wall

plate (b)

Min.

ceiling

height*

Image

width

(w)

Image

height

(h)

Min.

Projection

distance

(a)

Distance

from top

of image

to wall

plate (b)

55”

— — — — — 2129 1118 838 94 275 — — — — —

56”

— — — — — 2149 1138 853 104 280 — — — — —

57”

— — — — — 2188 1158 869 113 284 — — — — —

58”

— — — — — 2208 1179 884 122 289 — — — — —

59”

2073 1271 794 68 262 2228 1199 899 131 293 — — — — —

60”

2090 1292 808 76 266 2248 1219 914 140 297 2078 1328 747 90 314

61”

2107 1314 821 84 270 2267 1240 930 149 302 2095 1350 760 98 319

62”

2125 1335 835 92 274 2287 1260 945 158 306 2112 1373 772 106 324

63”

2142 1357 848 100 278 2307 1280 960 168 311 2129 1395 785 114 329

64”

2160 1379 862 108 282 2326 1300 975 177 315 2146 1417 797 123 333

65”

2177 1400 875 117 286 2346 1321 991 186 320 2163 1439 809 131 338

66”

2194 1422 888 125 290 2366 1341 1006 195 324 2181 1461 822 139 343

67”

2212 1443 902 133 294 2385 1361 1021 204 329 2198 1483 834 148 348

68”

2229 1465 915 141 298 2405 1382 1036 213 333 2215 1505 847 156 352

69”

2247 1486 929 149 302 2425 1402 1052 223 338 2232 1528 859 164 357

70”

2264 1508 942 157 306 2444 1422 1067 232 342 2249 1550 872 173 362

71”

2281 1529 956 165 310 2464 1443 1082 241 346 2267 1572 884 181 366

72”

2299 1551 969 173 313 2487 1463 1097 250 351 2284 1594 897 189 371

73”

2316 1572 983 181 317 2504 1483 1113 259 355 2301 1616 909 198 376

74”

2334 1594 996 189 321 2523 1504 1128 268 360 2318 1638 921 206 381

75”

2351 1615 1010 197 325 2510 1524 1143 277 364 2335 1660 934 214 385

76”

2368 1637 1023 205 329 2543 1544 1158 287 369 2352 1682 946 223 390

15

English

* Based on an image 762 mm from the floor; if the image is lower, the minimum ceiling height is reduced by the corresponding measurement.

77”

2386 1659 1037 214 333 2563 1565 1173 296 373 2370 1705 959 231 395

78”

2403 1680 1050 222 337 2582 1585 1189 305 378 2387 1727 971 239 400

79”

2420 1702 1063 230 341 2602 1605 1204 314 382 2404 1749 984 247 404

80”

2438 1723 1077 238 345 2622 1626 1219 323 389 2421 1771 996 256 409

81”

2455 1745 1090 246 349 2641 1646 1234 332 391 2438 1793 1009 264 414

82”

2473 1766 1104 254 353 2661 1666 1250 342 395 2456 1815 1021 272 418

83”

2490 1788 1117 262 357 2681 1687 1265 351 400 2473 1837 1034 281 423

84”

2507 1809 1131 270 361 2700 1707 1280 360 404 2490 1860 1046 289 428

85”

2525 1831 1144 278 365 2720 1727 1295 369 409 2507 1882 1058 297 433

86”

2542 1852 1158 286 369 — — — — — 2524 1904 1071 306 437

87”

2560 1874 1171 294 372 — — — — — 2542 1926 1083 314 442

88”

2577 1895 1185 303 376 — — — — — 2559 1948 1096 322 447

89”

2594 1917 1198 311 380 — — — — — 2576 1970 1108 331 452

90”

2612 1939 1212 319 384 — — — — — 2593 1992 1121 339 456

91”

2629 1960 1225 327 388 — — — — — 2610 2015 1133 347 461

92”

2647 1982 1239 335 392 — — — — — 2627 2037 1146 356 466

93”

2664 2003 1252 343 396 — — — — — 2645 2059 1158 364 471

94”

2681 2025 1265 351 400 — — — — — — — — — —

95”

2699 2046 1279 359 404 — — — — — — — — — —

96”

2716 2068 1292 367 408 — — — — — — — — — —

Diagonal

image

size

(S)

16:10 WXGA 4:3 XGA 16:9 Widescreen

Min.

ceiling

height*

Image

width

(w)

Image

height

(h)

Min.

projection

distance

(a)

Distance

from top

of image

to wall

plate (b)

Min.

ceiling

height*

Image

width

(w)

Image

height

(h)

Min.

projection

distance

(a)

Distance

from top

of image

to wall

plate (b)

Min.

ceiling

height*

Image

width

(w)

Image

height

(h)

Min.

Projection

distance

(a)

Distance

from top

of image

to wall

plate (b)

16

If you have a pre-existing whiteboard, refer to the table below to identify common models and sizes. If your

board is listed here, use the dimensions to reference the installation requirements found on pages 12 to 15.

Interactive whiteboard sizes

Diagonal size 16:10 WXGA 4:3 XGA 16:9 Widescreen

60 inches — — RM ClassBoard2 60

63 inches — Hitachi® StarBoard FX-63 —

64 inches — SMART Board 660

Promethean ActivBoard 164

—

71 inches — — INTERWRITE BOARD 1071

77 inches — Hitachi Cambridge Board 77

Hitachi StarBoard FX-77

SMART Board 680

—

77.5 inches — RM ClassBoard2 77.5

INTERWRITE® BOARD 1077

—

78 inches PolyVision® TS 600/ TS610 /

TSL610/ENO 2610

PolyVision TS610

Promethean ActivBoard 178 / 378

—

82 inches — — Hitachi StarBoard FX-82W

85 inches — — INTERWRITE BOARD 1085

87 inches

SMART Board

™ 685

Promethean ActivBoard 387

——

93 inches — — PolyVision ENO 2810

94 inches — — SMART Board 690

96 inches Epson BrightLink 455Wi — —

17

English

5. Installing the Projector

Make sure to follow the steps below to install the setting plate. If you ignore these steps, the setting plate

could fall and cause personal injury or property damage.

A Install the wall plate on the wall

(1) Determine the template sheet position.

• From the tables on pages 12 to 15, confirm the screen size (S) and the distance between the

projection surface and wall plate (b).

• Align the CTR line (vertical) of the template sheet with the center line (vertical) of the projection

surface.

Confirm where the beams or studs are within the wall, and shift the position left or right as necessary.

The position can be shifted horizontally left or right from the center line of the projection surface by

up to 1.77 in. (45 mm).

• Align the line (horizontal) on the template with the height of (b).

The maximum combined weight of the setting plate and the projector is approximately 33.5 lb

(15.2 kg). When you install the setting plate, calculate the permissible weight, carefully check

the construction, material, and strength of the wall, and perform the installation properly using

the most appropriate method.

Center line of projection surface

CTR line of template sheet

line on template sheet

65 mm (2.55 in.)

18

(2) Attach the template sheet to the wall.

If you need to install a junction box, you can use the cutout areas in the wall plate for the box.

The junction box needs to be recessed into the wall if you want to use the wall plate cover.

(3) Make mounting holes in the wall in the required locations.

The wall plate needs to be secured by commercially available anchors or lag bolts in the

following places. It is recommended that the wall plate be secured in at least three places.

• If securing the wall plate in four places, make the holes indicated by A or B in the figure.

• If securing the wall plate in three places, make the holes indicated by C in the figure.

(4) Remove the template sheet.

(5) Mount the wall plate on the wall.

B Determine the projection distance and pull out the slider

(1) Using the tables on pages 12 to 15, calculate the distance (a) from the projection surface to

the front of the projector.

(2) Loosen the four screws and pull out the slider on the setting plate.

❏ When you mount the projector on the wall with the setting plate, the wall needs to be

strong enough to hold the projector and the setting plate. Confirm the weight of the

projector and the setting plate before installation, and maintain the strength of the wall. If

the wall is not strong enough, reinforce the wall before installation.

❏ Install the setting plate so that it can sufficiently support the weight of the projector and

setting plate, and resist any horizontal vibration. Use M8 nuts and bolts. Nuts and bolts

smaller than M8 could cause the setting plate to fall.

❏ Epson takes no responsibility for any damage or injury caused by incorrect installation.

Warning

Four mounting holes

Three mounting holes

19

English

Align the slider with the mark on the slider measure that is a distance (a+x) equivalent to the

distance (a) plus the thickness of the board (x). See the tables on pages 12 to 15. The

recommended range for projection distance (a) is 2.76 to 14.57 in. (7 to 37 cm).

C Attach the setting plate to the wall plate

(1) Position the cables between the two screws and pass the cables through the setting plate

(

A).

(2) Hang the setting plate hook onto the wall plate bar (

B).

(3) Tighten the two M8 x 15 mm hexagon socket head cap bolts and two M8 x 45 mm hexagon

socket head cap bolts supplied with the setting plate so that the setting plate becomes

vertical against the wall (

C).

Use the two M8 x 45 mm hexagon socket head cap bolts to adjust the vertical position.

s 25

Screws (4 )

Slider measure

Take care not to trap the cables between the setting plate and wall plate.

Caution

Setting plate

Cables

Wall plate

M8 x 15 mm hexagon socket

head cap bolts (one on left

and one on right)

Wall plate bar

M8 x 45 mm hexagon

socket head cap bolts (2)

Setting plate hook

20

D Secure the projector to the setting plate

(1) Loosen the two screws and remove the cable cover from the projector.

(2) Insert the slide plate into the setting plate from the interface side of the projector (

A).

Align the marks on the projector and the setting plate (

B).

(3) Tighten the two M5 x 12 mm hexagon socket head cap bolts (

C).

Cable cover

Screws (2)

Projector

interface side

M5 x 12 mm hexagon

socket head cap bolts (2)

Marks

Bolt positions

Slide plate

If you use adhesives to prevent the screws from loosening or things such as lubricants or oils

on the slide plate, the case may crack and cause the projector to fall, resulting in personal

injury or property damage. Do not use adhesives, lubricants, or oils to install or adjust the

setting plate.

Warning

Page is loading ...

Epson BrightLink 455Wi Installation guide

This manual is also suitable for

Epson BrightLink 455Wi Installation guide

in other languages

Related papers

Other documents