Briggs & Stratton 030448-0 Owner's manual

Brand: Briggs & Stratton

Model: 030448-0

Category: Power generators

Type: Owner's manual

This manual is also suitable for

PORTAbLE GENERATOR

PortableGenerator

Operator'sManual

This generator is rated in accordance with CSA (CanadianStandards

Association) standard 022.2 No. 100-04 (motors and generators).

BRIGGS & STRATTONPOWER PRODUCTSGROUP, LLC

JEFFERSON, WISCONSIN, U.S.A.

Manual No. 209443GS Revision - (04/02/2009)

Thankyou for purchasing this quality-built Briggs & Stratton generator.We arepleasedthat you've placedyour confidence in

the Briggs & Stratton brand. When operatedand maintained according to the instructions in this manual,your Briggs &

Stratton generator will provide many years of dependableservice.

Thismanualcontainssafety information to makeyou awareof the hazardsand risks associatedwith generators and how to

avoid them. This generator is designed and intendedonly for supplying electrical powerfor operatingcompatible electrical

lighting, appliances,tools and motor loads,andis not intendedfor any other purpose.It is important that you readand

understand these instructions thoroughly before attemptingto start or operatethis equipment. Save these instructionsfor

future reference.

Thisgenerator requiresfinal assembly beforeuse. Referto the Assemb/ysection of this manualfor instructions on final

assembly procedures. Follow the instructions completely.

Whereto FindUs

You neverhaveto lookfar to find Briggs & Stratton support and servicefor your generator.Consultyour Yellow Pages.There

are over 30,000 Briggs & Stratton authorizedservicedealersworldwide who provide qualityservice.You canalso contact

Briggs & Stratton CustomerServiceby phone at (800) 743-4115, or on the Internetat BRIGGSandSTRATTON.COM.

Generator

Model Number

Revision I I I

Serial Number

Engine

Model Number

Type Number LLL_ I I I

Code Number

DatePurchased

IIIIIIIII

Briggs & Stratton PowerProducts Group, LLC

900 North Parkway

Jefferson, WI 53549

material may be reproduced or transmitted in any form

without the expresswritten permission of Briggs & Stratton

Power Products Group, LLC.

2 BRIGGSandSTRATTON.COIVl

TableofContents

Operator Safety ................................. 4

Equipment Description......................................... 4

Important SafetyInformation.................................... 4

Assembly ..................................... 7

UnpackGenerator ............................................ 7

Install Wheel Kit.............................................. 7

Add Engine Oil............................................... 8

Add Fuel.................................................... 8

System Ground .............................................. 9

Connectingto a Building's ElectricalSystem........................ 9

GeneratorLocation ........................................... 9

FeaturesandControls............................ 10

Cord Sets and Receptacles.................................... 11

Operation .................................... 12

Starting the Engine .......................................... 12

Connecting ElectricalLoads.................................... 13

Stopping the Engine.......................................... 13

Warm Weather Operation ..................................... 13

Don't OverloadGenerator ..................................... 14

Maintenance .................................. 15

MaintenanceSchedule........................................ 15

GeneratorMaintenance....................................... 15

FuelValveMaintenance....................................... 15

Engine Maintenance.......................................... 16

Storage ................................................... 18

Troubleshooting ................................ 19

Warranties.................................... 20

Emissions Control System Warranty............................. 20

GeneratorOwnerWarranty .................................... 22

Specifications ................................. 24

Product Specifications........................................ 24

Common Service Parts ....................................... 24

Espafiol

OperatorSafety

Equipment Description

Readthis manualcarefully and becomefamiliar

...... with yourgenerator. Knowitsapplications, its

limitationsand anyhazardsinvolved.

Thegeneratoris an engine-driven, revolvingfield, alternating

current (AC)generator. It was designedto supplyelectrical

power for operatingcompatible electricallighting, appliances,

tools and motor loads.Thegenerator's revolvingfield is

driven at about3,600 rpm by a single-cylinderengine.

NOTICE Exceedinggeneratorswattage/amperagecapacity

candamagegeneratorand/or electricaldevicesconnectedto

it.

• DONOTexceedthegenerator'swattage/amperagecapacity.See

Don'tOverloadGeneratorintheOperationsection.

Everyeffort hasbeen madeto ensurethat the information in

this manualis both accurateand current. However,the

manufacturer reservesthe right to change,alter or otherwise

improve the generatorand this documentation at anytime

without prior notice.

The EmissionControl System for this generator is warranted

for standardsset by the Environmental ProtectionAgency

and the California Air Resources Board.

Important Safety Information

The manufacturer cannot possibly anticipateevery possible

circumstance that might involvea hazard.Thewarnings in

this manual,and the tags and decals affixedto the unit are,

therefore, not all-inclusive. If you usea procedure, work

method or operating technique that the manufacturerdoes

not specifically recommend, you must satisfy yourself that it

is safe for you and others. You must also make surethat the

procedure, work method or operating technique that you

choose does not renderthe generator unsafe.

SafetySymbolsand Mleanings

ToxicFumes Kickback ElectricalShock

Fire

Explosion Operator'sManual

MovingParts FlyingObjects HotSurface

Thesafety alertsymbol indicatesa potential personal

injury hazard.A signalword (DANGER,WARNING,or

CAUTION)is usedwith the alert symbol to designatea

degreeor levelof hazardseriousness.A safety symbol may

be usedto representthe type of hazard.Thesignal word

NOTICEis usedto address practicesnot relatedto personal

injury.

_i, DANGER indicatesa hazardwhich, if not avoided, will

result in deathor serious injury.

_i, WARNINGindicatesa hazardwhich, if not avoided,

could result in death or serious injury.

_i, CAUTIONindicates a hazardwhich, if not avoided, could

result in minor or moderate injury.

NOTICEaddress practices not relatedto personal injury.

4 BRIGGSandSTRATTON.COIVl

Using a generator indoors CAN KiLL YOU iN MINUTES,

Generator exhaust contains carbon monoxide, This is

a poison you cannot see or smelJ,

V V

NEVER use inside a home

or garage, EVEN iF doors

and windows are open,

Only use OUTSIDE and

far away from windows,

doors, and vents,

_i, WARNING Runningengine gives off carbon

monoxide, an odorless, colorless, poison gas.

_ Breathing cancause headache,

carbon monoxide

fatigue, dizziness,vomiting, confusion, seizures,

nausea,fainting or death.

• OperategeneratorONLYoutdoors.

• Installa batteryoperatedcarbonmonoxidealarmnearthe

bedrooms.

Keepexhaustgas from entering a confined areathrough

windows, doors, ventilation intakes,or other openings.

DO NOTstart or run engine indoors or in an enclosedarea,

(even if windows and doors areopen), including the generator

compartment of arecreationalvehicle (RV).

_i, WARNING Theengine exhaustfrom this product

contains chemicals known to the State of California to

causecancer, birth defects,or other reproductive harm.

_i, WARNING Certain components in this product and

relatedaccessoriescontain chemicals known to the State

of Californiato causecancer, birth defects or other

reproductive harm. Wash hands after handling.

_i, WARNING Starter cord kickback(rapid retraction)can

result in bodily injury. Kickbackwill pull hand and

,_. arm toward enginefaster thanyou can let go.

Broken bones,fractures, bruises, or sprains

could result.

• Whenstartingengine,pullcordslowlyuntilresistanceisfelt

andthenpullrapidlytoavoidkickback.

• NEVERstartor stopenginewithelectricaldevicespluggedin

andturnedon.

_i, WARNING Generator produces hazardous voltage.

")Jl|l Failure to isolate generator from power utility can

result in death or injury to electric utility workers

due to backfeed of electrical energy.

• When using generator for backup power, notify utility company.

Useapproved transfer equipment to isolate generatorfrom

electric utility.

• Usea ground fault circuit interrupter (GFCI)in any damp or

highly conductive area,such asmetal deckingor steel work.

• DO NOTtouch barewires or receptacles.

• DO NOTuse generatorwith electrical cords which areworn,

frayed,bare or otherwise damaged.

• DO NOToperate generator in the rain or wet weather.

• DO NOThandle generatoror electricalcords while standing in

water, while barefoot,or while hands or feet arewet.

• DO NOTallow unqualified personsor children to operate or

servicegenerator.

_i, WARNING Fuel and its vapors are extremely

flammable and explosive.

Fire or explosion can cause severe burns

or death.

WHENADDINGOR DRAININGFUEL

• Turn generator OFFand let it cool at least2 minutes before

removing fuel cap. Loosencap slowly to relievepressure in

tank.

• Fill or drain fuel tank outdoors.

• DONOToverfill tank. Allow spacefor fuel expansion.

• Iffuel spills, wait until it evaporatesbefore starting engine.

• Keepfuel awayfrom sparks, open flames, pilot lights, heat,and

other ignition sources.

• DONOTlight a cigaretteor smoke.

WHENSTARTINGEQUIPMENT

• Ensurespark plug, muffler,fuel cap,andair cleanerarein place.

• DO NOTcrank enginewith spark plug removed.

WHENOPERATINGEQUIPMENT

• DONOTtip engine or equipmentat anglewhich causesfuel to

spill.

• This generator is not for use inmobile equipment or marine

applications.

WHENTRANSPORTINGOR REPAIRINGEQUIPMENT

• Transport/repair with fuel tank EMPTYor with fuel shutoff valve

OFF.

• Disconnectspark plug wire.

WHENSTORINGFUELOR EQUIPMENTWITH FUELIN TANK

• Store awayfrom furnaces, stoves,water heaters,clothes

dryers, or other appliancesthat have pilot light or other ignition

source becausethey can ignitefuel vapors.

A WARNING

This generatordoes not meet U. S. CoastGuard Regulation

33CFR-183and should not beused on marineapplications.

Failureto usethe appropriate U. S. CoastGuard approved

generator could result in death or serious injury and/or

property damage.

_i, WARNING Contact with muffler area can result in

serious burns.

_ _ Exhaust heat/gases can ignite

combustibles, structures or damage

fuel tank causing a fire.

• DO NOTtouch hot parts and AVOID hot exhaust gases.

• Allow equipmentto cool beforetouching.

• Keepat least5 feet (152 cm) of clearanceon all sidesof

generator including overhead.

• It is a violation of California Public Resource Code,Section

4442, to use or operate the engineon anyforest-covered,

brush-covered, or grass-covered land unlessthe exhaust

system is equipped with aspark arrester, as defined in Section

4442, maintained in effective working order. Other statesor

federal jurisdictions may havesimilar laws.

Contactthe original equipment manufacturer, retailer, or dealer

to obtain a sparkarrester designed for the exhaust system

installed on this engine.

• Replacement parts must bethe sameand installed in the same

position asthe original parts.

_i, WARNING Unintentional sparking can result in fire or

,_¢ electric shock.

WHENADJUSTINGOR MAKINGREPAIRSTO YOURGENERATOR

• Disconnectthe spark plug wire from the spark plug and place

the wire where it cannot contact spark plug.

WHENTESTINGFORENGINESPARK

• Use approved spark plug tester.

• DO NOTcheckfor spark with spark plug removed.

_i, WARNING Starter and other rotating parts can

entangle hands, hair, clothing, or accessories.

• NEVERoperate generator without protective housing or covers.

• DO NOTwear looseclothing, jewelry or anythingthat may be

caught in the starter or other rotating parts.

• Tie up long hairand removejewelry.

_i, CAUTION Excessively high operating speeds increase

risk of injury and damage to generator.

Excessively low speeds impose a heavy load.

• DO NOTtamper with governed speed. Generatorsupplies

correct rated frequency and voltage when running at governed

speed.

• DO NOTmodify generator inany way.

NOTICE Exceeding generators wattage/amperage capacity

can damage generator and/or electrical devices connected to

it.

• DO NOTexceedthe generator's wattage/amperage capacity. See

Don't OverloadGeneratorinthe Operationsection.

• Start generatorand letengine stabilize beforeconnecting

electrical loads.

• Connectelectrical loads in OFFposition, thenturn ONfor

operation.

• Turn electricalloads OFFanddisconnect from generator before

stopping generator.

NOTICE Improper treatment of generator can damage it

and shorten its life.

• Use generator only for intendeduses.

• If you havequestions about intended use,ask dealeror contact

local service center.

• Operategenerator only on levelsurfaces.

• DO NOTexposegenerator to excessivemoisture, dust, dirt, or

corrosive vapors.

• DO NOTinsert any objectsthrough cooling slots.

• If connected devicesoverheat, turn them off anddisconnect them

from generator.

• Shut off generator if:

-electrical output is lost;

-equipment sparks, smokes, or emits flames;

-unit vibrates excessively.

6 BRIGGSandSTRATTON.COIVI

Assembly

F[-_-_I Read entireoperator'smanualbeforeyou attempt

toassemble or operateyournewgenerator.

Your generator requiressome assembly and is readyfor use

after it hasbeen properly servicedwith the recommendedoil

and fuel.

If you haveany problemswith the assemblyof your generator,

pleasecallthe generatorhelplineat (800) 743-4115. If calling

for assistance,pleasehavethe model, revision,and serial

numberfrom the identificationlabel available.SeeGenerator

Featuresand Controlsfor identificationlabellocation.

UnpackGenerator

1. Setthe carton on a rigid, flat surface.

2. Removeeverything from carton exceptgenerator.

3. Opencarton completely by cutting eachcorner from

top to bottom.

4. Leavegeneratoron carton to install wheel kit.

The generatoris suppliedwith:

• Engineoil bottle

• Operator's manual

• Wheelkit

Install Wheel Kit

NOTICE Wheelkit is not intendedfor over-the-road use.

You will needthe following tools to install thesecomponents:

• 10 mm and 13 mm wrenches

• Socketwrench with 10mm and13 mm sockets

• Adjustable wrenches(2)

Install the wheel kit as follows:

1. Tip generatorso that engine end is up.

2. Placeaxlestud (A) through mounting bracketon

generatorframe.

3. Placea flat washer (B) on axlestud as shown.

4. Use adjustablewrenches to securethe axle stud to

frame with jam nut (C).

5. Placea flat washer (B), then wheel (D) on axleas

shown.

NOTICE Besure to install wheelwith raised hub inboard.

6. Use an adjustablewrench to securethe wheel to axle

stud with jam nut.

7. Repeatsteps 2 through 6 for other wheel.

8. Tip generatorso that engine side is down.

9. Line up holes in support leg (E) with holes in generator

frame.

10. Attachsupport leg usingtwo 20 mm bolts (F) and two

hex nuts (G).Tightenwith 10 mm and 13 mm wrenches.

11. Return generatorto normal operating position (resting

on wheels and support legs).

12. Line up holes in handle (H) with holes in generator

frame. Attach handle using 10 mm and 13 mm

wrencheswith 35 mm bolts (J) and hex nuts (K).

Add Engine Oil

1. Placegeneratoron a flat, levelsurface.

2. Cleanarea around oil fill and removeyellow oil fill cap.

3. Using oil funnel (optional), slowly pour contents of

provided oil bottle into oil fill opening.

NOTICE Improper treatment of generator can damage it

and shorten its life.

• DO NOTattempt to crank or start the engine beforeit has been

properly servicedwith the recommended oil.This may result in an

enginefailure.

4. Replaceoil fill cap and fully tighten.

Add Fuel

Fuel mustmeet theserequirements:

• Clean,fresh, unleadedgasoline.

• A minimum of 87 octane/87AKI (91 RON).High

altitude use, seeHigh Altitude.

• Gasolinewith up to 10% ethanol (gasohol) or upto

15% MTBE(methyl tertiary butyl ether) is acceptable.

NOTICE Avoid generatordamage.

Failureto follow Operator's Manualfor fuel

recommendations voids warranty.

• DONOTuseunapprovedgasolinesuchasE85.

• DONOTmixoil in gasoline.

• DONOTmodifyengineto runonalternatefuels.

To protect the fuel system from gum formation, mix in a fuel

stabilizerwhen adding fuel. SeeStorage.All fuel is not the

same. If you experiencestarting or performanceproblems

after using fuel, switch to a different fuel provider or change

brands. This engine is certified to operateon gasoline. The

emission control system for this engine is EM (Engine

Modifications).

_i, WARNING Fueland its vapors are extremely

flammable and explosive.

Fireor explosion can causesevereburns

or death.

WHENADDINGFUEL

• Turn generator OFFand let it cool at least2 minutes before

removing fuel cap. Loosencap slowly to relievepressure in

tank.

• Fill fuel tank outdoors.

• DONOToverfill tank. Allow spacefor fuel expansion.

• Iffuel spills, wait until it evaporatesbefore starting engine.

• Keepfuel awayfrom sparks, open flames, pilot lights, heat,and

other ignition sources.

• DONOTlight a cigaretteor smoke.

Cleanarea around fuel fill cap, remove cap.

Slowly add unleadedgasoline (A) to fuel tank (B). Be

careful not to fill abovethe baffle (C). This allows

adequatespace for fuel expansion asshown.

3. Install fuel capand let anyspilled fuel evaporatebefore

starting engine.

HighAltitude

At altitudes over 5,000 feet (1524 meters), a minimum

85 octane/ 85 AKI (89 RON)gasoline is acceptable.To

remainemissions compliant, high altitude adjustment is

required.Operationwithout this adjustmentwill cause

decreasedperformance,increasedfuel consumption, and

increasedemissions. SeeanauthorizedBriggs & Stratton

dealerfor high altitude adjustment information. Operation of

the engine at altitudes below 2,500 feet (762 meters) with

the high altitude kit is not recommended.

8 BRIGGSandSTRATTON.COIVl

SystemGround

Thegenerator hasa system ground that connects the

generatorframe components to the ground terminals on the

ACoutput receptacles.Thesystem ground is connected to

the ACneutral wire (the neutral is bonded to the generator

frame).

Special Requirements

Theremay be Federalor State OccupationalSafetyand

Health Administration (OSHA)regulations, local codes, or

ordinances that applyto the intended useof the generator.

Pleaseconsult a qualified electrician, electrical inspector, or

the local agency havingjurisdiction:

• Insome areas,generators are requiredto be registered

with local utility companies.

• If the generator is used at a construction site, there

may be additional regulations which must beobserved.

Connecting to a Building'sElectricalSystem

Connectionsfor standby powerto a building's electrical

system must be made bya qualified electrician. The

connection must isolate the generator power from utility

power or other alternative power sources and must comply

with all applicablelaws and electrical codes.

_i, WARNING Generatorproduces hazardousvoltage.

')Jib Failureto isolate generatorfrom power utility can

result in death or injury to electric utility workers

due to backfeedof electrical energy.

• Whenusinggeneratorfor backuppower,notifyutilitycompany.

Useapprovedtransferequipmentto isolategeneratorfrom

electricutility.

• Useagroundfaultcircuitinterrupter(GFCI)in anydampor

highlyconductivearea,suchasmetaldeckingor steelwork.

• DONOTtouchbarewiresor receptacles.

• DONOTusegeneratorwithelectricalcordswhichareworn,

frayed,bareor otherwisedamaged.

• DONOToperategeneratorintherainorwetweather.

• DONOThandlegeneratoror electricalcordswhilestandingin

water,whilebarefoot,or whilehandsorfeetarewet.

• DONOTallowunqualifiedpersonsor childrento operateor

servicegenerator.

GeneratorLocation

Clearancesand Air Movement

_i, WARNING Exhaustheat/gases can ignite

combustibles, structures or damagefuel tank

causing a fire.

• Keepat least5 ft. (152 cm) clearanceon all sidesof generator

including overhead.

Placegeneratoroutdoors in an areathat will not accumulate

deadlyexhaust gas. DONOTplacegeneratorwhere exhaust

gas (A) could accumulate and enter inside or be drawn into a

potentially occupied building. Ensureexhaust gas is kept

awayfrom any windows, doors, ventilation intakes, or other

openings that canallow exhaustgasto collect in a confined

area.Prevailingwinds and air currents should betaken into

consideration when positioning generator.

Using a generator indoors CAN KILL YOU IN MINUTES,

Generator exhaust contains carbon monoxide, This is

a poison you cannot see or smell,

NEVER use inside a home

or garage, EVEN IF doors

and windows are open.

Only use OUTSIDE and

far away from windows,

doors, and vents.

FeaturesandControls

Readthis operator'smanualand safetyrulesbeforeoperatingyourgenerator.

Comparethe illustrations with your generator,to familiarize yourself with the locations of various controls and

adjustments. Savethis manual for future reference.

A- SparkArresterMuffler -- Exhaustmuffler lowers engine

noiseand isequippedwith a spark arrester screen.

B- EngineIdentification-- Provides model, typeand code

of engine. Pleasehavethese readilyavailableif calling for

assistance.

C- Choke Lever -- Usedwhen starting a cold engine.

D- Fuel Valve-- Usedto turn fuel supply on and off to

engine.

E - Air Cleaner -- Protects engineby filtering dustand

debris out of intake air.

F - Recoil Starter-- Usedto start the engine.

G - 0il DrainPlug-- Drainengine oil here.

H- 0il Fill Cap -- Checkand add engine oil here.

J - 120 Volt AC,20 Amp,Duplex Receptacle-- May be

used to supply electrical power for the operation of

120 Volt AC, 20 Amp, single phase, 60 Hzelectrical,

lighting, appliance,tool, andmotor loads.

K- 120/240 Volt AC,20 AmpLockingReceptacle-- May

be usedto supplyelectrical power for the operation of

120 and/or 240 Volt AC, 20 Amp, single phase,60 I-Iz

electrical, lighting, appliance,tool and motor loads.

L - DoublePole CircuitBreaker(AC)-- A double pole

circuit breakeris providedto protect the generator

against electricaloverload.

M - FuelTank-- Capacityof four (4) U.S.gallons (15 L).

N - RockerSwitch-- Setthis switch to "On" before using

recoil starter. Set switch to "Off" to stop engine.

Items NotShown:

GroundingFastener-- Consultyour local agency having

jurisdiction for grounding requirements in your area.

IdentificationLabel-- Provides model, revision, and serial

number of generator. Pleasehavethese readily available

when calling for assistance.

10 BRIGGSandSTRATTON.COIVl

CordSetsandReceptacles

Use only high quality, well-insulated, grounded extension

cords with the generator's 120 Volt duplex receptacle.

Inspect extensioncords before eachuse.

Checkthe ratings of all extensioncords beforeyou use

them. Extensioncord sets usedshould be ratedfor 125 Volt

ACloads at 20 Amps or greaterfor most electrical devices.

Somedevices, however, may not requirethis type of

extension cord. Checkthe operator's manuals of those

devicesfor the manufacturer's recommendations.

Keepextension cords asshort aspossible to minimize

voltage drop.

_k WARNING Overloadedelectrical cords can overheat,

arc, and burn resulting in death, bodily injury,

and/or property damage.

• ONLYusecordsratedfor yourloads.

• Followallsafetiesonelectricalcords.

120/240 Volt AC,20 Amp, LockingReceptacle

Use a NEMA L14-20 plug with this receptacle.Connecta

4-wire cord set ratedfor 250 Volt ACloads at 20 Amps (or

greater). You can usethe same4-wire cord if you plan to

run a 120 Volt load.

__l,_/Wire Cord Set

(Neutral)

Y(Hot) | X(Hot)

NEMA L14-20 /-7[-7 Ground (Green)

This receptaclepowers 120/240 Volt AC, 60 Hz,single phase

loads requiring up to 3,250 watts of power (3.25 kW) at

13.5 Amps for 240 Volts or two independent120 Volt loads

at 13.5 Amps each.Theoutlet is protected by adouble pole

circuit breaker.

NOTICE Receptacles may be marked with rating value

greater than generator output capacity.

• NEVERattempt to power adevice requiring moreamperagethan

generator or receptaclecan supply.

• DONOToverloadthe generator.SeeDon't OverloadGenerator.

120 Volt AC, 20 Amp, DuplexReceptacle

Theduplex receptacleis protected against overload by a

double pole circuit breaker.

Useeachreceptacleto operate120 Volt AC, single-phase,

60 Hz electricalloads requiring up to 2,400 watts (2.4 kW) at

20 Amps of current. Usecord setsthat are ratedfor 125Volt

ACloads at 20 Amps (or greater).

Operation

Starting the Engine

Disconnect all electrical loads from the generator. Usethe

following start instructions:

1. Make sure unit is on a levelsurface.

NOTICE Failureto start and operatethe unit on a level

surfacewill causethe unit not to start or shut down during

operation.

2. Turn thefuel valve (A) to the "On" position.

3. Push choke leverto "Choke" position.

4. Push engine rocker switch to "On".

5. Grasp recoil handleand pull slowly until slight

resistance is felt. Then pull handle rapidly to overcome

compression, prevent kickback, and start engine.

_i, WARNING Starter cord kickback(rapid retraction) can

result in bodily injury. Kickbackwill pull hand and

,_arm toward enginefasterthan you can let go.

Broken bones,fractures, bruises, or sprains

could result.

• Whenstartingengine,pullcordslowlyuntilresistanceisfelt

andthenpull rapidlytoavoidkickback.

• NEVERstartor stopenginewith electricaldevicespluggedin

andturnedon.

NOTICE If excessivefuel is present in the air/fuel mixture

causing a "flooded" condition, move the choke leverto

"Run" position and pull the handle repeatedlyuntil the

engine starts.

6. Move choke leverto "Run" position ashort distance at

a time over several secondsin warm weather or

minutes in cold weather. Letengine run smoothly

before eachchange. Operatewith chokein "Run"

position.

NOTICE If the engine starts after 3 pulls but fails to run, or

if the unit shuts down during operation, make sure the unit

is on a levelsurfaceand checkfor the proper oil level in the

crankcase.This unit maybe equipped with a low oil

protection device.

_i, WARNING Contact with muffler area can result in

serious burns.

._ ,_ Exhaust heat/gases can ignite

combustibles, structures or damage

fuel tank causing a fire.

• DO NOTtouch hot parts andAVOIDhot exhaust gases.

• Allow equipment to cool beforetouching.

• Keepat least5 feet (152 cm) of clearanceon all sides of

generator including overhead.

• It is a violation of California Public Resource Code,Section

4442, to use or operate the engine on any forest-covered,

brush-covered, or grass-covered land unless the exhaust

system is equipped with aspark arrester, as defined in Section

4442, maintained in effective working order. Other statesor

federaljurisdictions may havesimilar laws.

Contactthe original equipment manufacturer, retailer, or dealer

to obtain a spark arrester designedfor the exhaust system

installed on this engine.

• Replacement parts must bethe sameand installed in the same

position asthe original parts.

12 BRIGGSandSTRATTON.COIVl

Connecting Electrical Loads

1. Let engine stabilizeand warm upfor a few minutes

after starting.

2. Plug in andturn on the desired 120 and/or 240 Volt AC,

single phase, 60 Hzelectrical loads.

NOTE:

• DONOTconnect 240 Volt loads to the 120 Volt duplex

receptacles.

• DONOTconnect 3-phaseloads to the generator.

• DONOTconnect 50 Hzloads to the generator.

• DONOTOVERLOADTHEGENERATOR.SeeDon't

OverloadGenerator.

NOTICE Exceeding generators wattage/amperage capacity

can damage generator and/or electrical devices connected to

it.

• DO NOTexceedthe generator's wattage/amperage capacity. See

Don't OverloadGeneratorinthe Operationsection.

• Start generatorand letengine stabilize beforeconnecting

electrical loads.

• Connectelectrical loads in OFFposition, thenturn ONfor

operation.

• Turn electricalloads OFFand disconnectfrom generatorbefore

stopping generator.

Stopping the Engine

1. Turn OFFand unplug all electrical loadsfrom generator

panel receptacles.NEVERstart or stop enginewith

electrical devicesplugged in and turned ON.

2. Let engine run at no-load for several minutes to

stabilize internaltemperatures of engine and generator.

3. Push engine rocker switch to "Off" position.

_i, WARNING Backfire,fire or enginedamagecould

occur.

• DONOTstop engineby moving chokecontrol to "Choke"

position (1_1).

4. Move fuel valve to "Off" position.

Warm Weather Operation

This generatorengine is equippedwith WeatherGuard,an

innovativefeature to preventcarburetor icing in cold weather

conditions. WeatherGuardhas beenengineeredto operatein

all weather conditions. However,product performancecan be

increasedwhen operatingthe generator solely in warm

weather by removing the WeatherGuardshield (A).

Remove the two screws (B) as shown. Store shield and

screws for future coldweather operation.

Don't OverloadGenerator

Capacity

You must make sureyour generator cansupply enough

rated (running) and surge (starting) watts for the items you

will power at the same time. Follow these simple steps:

1. Selectthe itemsyou will power at the sametime.

2. Total the rated(running) watts of theseitems. This is

the amount of power your generator must produce to

keepyour items running. SeeWattageReferenceGuide.

3. Estimatehow many surge (starting) watts you will need.

Surge wattageis the short burst of power neededto

start electric motor-driven tools or appliancessuch asa

circular saw or refrigerator. Becausenot all motors start

atthe sametime, total surgewatts can be estimatedby

adding only the item(s) with the highest additionalsurge

watts to thetotal ratedwatts from step2.

Example:

Tool orAppliance

Window Air

Conditioner

Refrigerator

DeepFreezer

Television

Light (75 Watts)

Rated (Running)

Watts

1200

800

500

3075 Total

Running Watts

AdditionalSurge

(Starting)Watts

1800

1600

5OO

1800 Highest

SurgeWatts

Total Rated(Running) Watts = 3075

HighestAdditional Surge Watts = 1800

Total GeneratorOutput Required =4875

Power Management

To prolong the life of your generatorand attacheddevices, it

is important to take carewhen adding electrical loadsto your

generator. Thereshould be nothing connectedto the

generator outlets before starting its engine.Thecorrect and

safe way to managegeneratorpower isto sequentiallyadd

loads asfollows:

1. With nothing connectedto the generator,start the

engine asdescribed in this manual.

2. Plug in andturn on the first load, preferablythe largest

load you have.

3. Permit the generatoroutput to stabilize (engine runs

smoothly and attacheddeviceoperates properly).

4. Plug in andturn on the next load.

5. Again, permit the generatorto stabilize.

6. Repeatsteps 4 and 5 for eachadditional load.

NEVERadd more loads than the generatorcapacity.Take

special careto considersurge loads ingenerator capacity,as

described above.

Wattage ReferenceGuide

Rated*

Tool or Appliance

Essentials

Light Bulb - 75 watt

DeepFreezer

Sump Pump

Refrigerator/Freezer- 18 cf

Water Well Pump- 1/3 hp

Heating/Cooling

Window AC- 10,000 BTU

Window Fan

FurnaceFanBlower- 1/2 hp

Kitchen

Microwave Oven- 1000Watt

CoffeeMaker

Electric Stove - Single Element

Hot Plate

Family Room

DVD/CDPlayer

VCR

Stereo Receiver

Color Television- 27 in

PersonalComputer w/17 in

monitor

Other

Security System

AM/FM Clock Radio

GarageDoor Opener- 1/2 hp

ElectricWater Heater- 40 gallon

DIY/JobSite

Quartz HalogenWork Light

Airless Sprayer- 1/3 hp

Reciprocating Saw

Electric Drill- 1/2 hp

Circular Saw - 7-1/4 in

MiterSaw- 10 in

TablePlaner- 6 in

TableSaw/RadialArm Saw- 10 in

Air Compressor - 1-1/2 hp

* Wattageslisted are approximate only.

appliancefor actual wattage.

(Running)

Watts

Additional

Surge

(Starting)

Watts

500 500

800 1200

800 1600

1000 2000

1200 1800

300 600

800 1300

1000

1500

2500

100

450

500

800

180

300

480 520

4000

1000

600 1200

960 960

1000 1000

1500 1500

1800 1800

2000 2000

2500 2500

Checktool or

14 BRIGGSandSTRATTON.COM

Maintenance

MaintenanceSchedule

Follow the hourly or calendarintervals, whichever occurs

first. More frequent serviceis requiredwhen operating in

adverseconditions noted below.

• Changeengine oil

• Cleandebris

• Checkengineoil level

_,_0_:_, :ii:ii:ii:ii:ii:ii:ii:ii:ii:ii:ii:ii:ii:ii:ii:ii:ii:ii:ii:ii

• Service engineair cleaner'

• Changeengine oil'

• Inspect muffler andsparkarrester

• Servicefuel filter

• Service spark plug

• Cleancooling system'

1 Service more often under dirty or dusty conditions.

GeneralRecommendations

Regularmaintenancewill improvethe performanceand extend

the life ofthe generator.Seeanyauthorizeddealerfor service.

Thegenerator's warranty doesnot cover items that have

been subjectedto operator abuseor negligence.To receive

full valuefrom the warranty, the operator must maintain the

generator asinstructed inthis manual.

Someadjustments will needto be made periodically to

properly maintain your generator.

All serviceand adjustments should be made at least once

eachseason.Follow the requirementsin the Maintenance

Schedulechart above.

NOTICE Oncea year you should cleanor replacethe spark

plug and replacethe air filter. A new spark plug and cleanair

filter assure proper fuel-air mixture and help your engine run

better and last longer.

EmissionsControl

Maintenance, replacement,or repair of theemissions

controldevicesand systemsmay be performedby any

non-roadengine repair establishmentor individual.

However,to obtain "no charge" emissions control service,

the work must be performed by a factory authorized dealer.

Seethe Emissions Warranty.

GeneratorMaintenance

Generatormaintenanceconsists of keepingthe unit clean

and dry. Operateand store the unit in a clean dry

environment where it will not be exposedto excessivedust,

dirt, moisture, or any corrosive vapors. Coolingair slots in

the generator must not become cloggedwith snow, leaves,

or any other foreign material.

NOTICE DONOTusewater or other liquids to clean

generator. Liquids canenter engine fuel system, causing

poor performance and/or failure to occur. In addition, if

liquid enters generator through cooling airslots, some of the

liquid will be retainedin voids and cracks of the rotor and

stator winding insulation. Liquid and dirt buildup on the

generator internalwindings will eventuallydecreasethe

insulation resistanceof these windings.

Cleaning

Dailyor before use, look around and underneaththe

generatorfor signs of oil or fuel leaks. Cleanaccumulated

debris from inside and outside the generator.Keepthe

linkage, spring and other engine controls clean. Inspect

cooling air slots and openings on generator.These openings

must be kept clean and unobstructed.

Engine parts should be kept cleanto reducethe risk of

overheating and ignition of accumulateddebris:

• Use a damp cloth to wipe exteriorsurfaces clean.

NOTICE Improper treatment of generator can damage it

and shorten its life.

• DO NOTexposegenerator to excessivemoisture, dust, dirt, or

corrosive vapors.

• DONOTinsert any objects through cooling slots.

• Use a soft bristle brush to loosen cakedon dirt or oil.

• Use a vacuum cleanerto pick up loose dirt and debris.

FuelValve Maintenance

Thefuel valve is equippedwith afuel sediment cup, screen,

retaining ring and o-ring that needto be cleanedevery

100 hours or once a year (whichever occurs first).

1. Move fuel valve to "Off" position.

2. Removesediment cup (A) from fuel valve. Remove

o-ring (B), retaining ring (C)and screen (D) from fuel

valve.

3. Washsedimentcup,o-ring,retainingring,andscreen

inanonflammablesolvent.Drythemthoroughly.

4. Placescreen,retainingring,ando-ringintofuelvalve.

Installsedimentcupandtightensecurely.

5. Movefuelvalveto"On"position,andcheckforleaks.

Replaceo-ringifthereisanyleakage.

EngineMaintenance

_i, WARNING Unintentionalsparking can result in fire or

_¢ electric shock.

WHENADJUSTINGORMAKINGREPAIRSTOYOUR

GENERATOR

• Disconnectthesparkplugwirefromthesparkplugandplace

thewirewhereit cannotcontactsparkplug.

WHENTESTINGFORENGINESPARK

• Useapprovedsparkplugtester.

• DONOTcheckfor sparkwith sparkplugremoved.

Oil

Oil Recommendations

We recommendthe useof Briggs & Stratton Warranty

Certified oils for best performance. Otherhigh-quality

detergent oils are acceptableif classifiedfor serviceSF, SG,

SH, SJ or higher. DONOTuse specialadditives.

Outdoor temperatures determine the proper oil viscosity for

the engine. Usethe chart to select the best viscosity for the

outdoor temperature range

104

-4

-22

expected.

°C

,__30

__20

__10

._ nO

-10

-20

-30

* Below40°F(4°C)theuseofSAE30 will resultin hardstarting.

** Above 80°F (27°C)the useof 10W30 may cause increased oil

consumption. Checkoil levelmore frequently.

O OTICE Synthetic oil meeting ILSACGF-2,API

certification mark and API servicesymbol with

"SJ/CF ENERGYCONSERVING"or higher, is an

acceptableoil at all temperatures. Useof synthetic

oil does not alter required oil changeintervals.

CheckingOil Level

Oil level should be checked prior to eachuseor at least

every 8 hours of operation. Keepoil levelmaintained.

1. Make sure generator is on a levelsurface.

2. Cleanarea around oil fill and remove oil fill cap.

3. Verify oil is atthe point of overflowing at oil fill opening.

4. Replaceand tighten oil fill cap.

AddingEngineOil

1. Make sure generatoris on a levelsurface.

2. Checkoil levelas described in CheckingOilLevel

3. If needed,slowly pour oil into oil fill opening to the

point of overflowing at oil fill.

4. Replaceand tighten oil fill cap.

ChangingEngineOil

If you are usingyour generator under extremely dirty or

dusty conditions, or in extremely hot weather, changethe oil

more often.

_i, CAUTION Avoid prolonged or repeatedskin contact

with usedmotor oil.

• Usedmotoroil hasbeenshownto causeskincancerin certain

laboratoryanimals.

• Thoroughlywashexposedareaswith soapandwater.

KEEPOUTOFREACHOFCHILDREN.DON'T

POLLUTE.CONSERVERESOURCES.RETURN

USEDOIL TOCOLLECTIONCENTERS.

Changethe oil while the engineis still warm from running,

asfollows:

Make sure unit is on a levelsurface.

Disconnectthe spark plug wire from the spark plug and

placethe wire where it cannot contact spark plug.

Cleanarea around oil drain plug (A). The oil drain plug

is located at baseof engine,opposite carburetor.

Removeoil drain plug and drain oil completely into a

suitable container.

Reinstall oil drain plug andtighten securely.Removeoil

fill cap.

Slowly pour oil (about 20 oz.) into oil fill opening (B) to

the point of overflowing (C) at oil fill cap. DONOT

overfill.

Reinstall oil fill cap. Fingertighten cap securely.

Wipe up anyspilled oil.

16 BRIGGSandSTRATTON.COIVl

Service Air Cleaner

Your enginewill not run properly and may be damaged if

you run it with a dirty air cleaner. Replacemore often if

operating under dirty or dusty conditions.

To servicethe air cleaner,follow these steps:

1. Loosen screws (A) and removeair cleanercover (B).

2. Carefully removecartridge (C) from base(D).

3. Cleanpaperfilter by tapping it gently on a solid surface.

If the paper filter is too dirty, replaceit with a new one.

Disposeof the old filter properly.

4. Install clean(or new) aircleanerassembly insidecover.

5. Assembleair cleanercoveronto baseand tighten screws.

Service Spark Plug

Changingthe spark plug will helpyour engine to start easier

and run better.

1. Cleanarea around spark plug.

2. Removeand inspect spark plug.

3. Checkelectrodegap with wire feeler gaugeand reset

spark plug gap to recommendedgap if necessary(see

Specifications).

4. Replacespark plug if electrodesare pitted, burned or

porcelain is cracked. Usethe recommended

replacementspark plug. SeeSpecifications.

5. Install spark plug and tighten firmly.

InspectMufflerand Spark Arrester

Inspect the muffler for cracks,corrosion, or other damage.

Removethe spark arrester, if equipped,and inspectfor

damageor carbon blockage. If replacementparts are

required, make sureto useonly original equipment

replacementparts.

_i, WARNING Contact with muffler area can result in

serious burns.

_ _ Exhaust heat/gases can ignite

combustibles, structures or damage

fuel tank causing a fire.

• DO NOTtouch hot parts andAVOIDhot exhaust gases.

• Allow equipment to cool beforetouching.

• Keepat least5 feet (152 cm) of clearanceon all sides of

generator including overhead.

• It is a violation of California Public Resource Code,Section

4442, to use or operate the engine on any forest-covered,

brush-covered, or grass-covered land unless the exhaust

system is equipped with aspark arrester, as defined in Section

4442, maintained in effective working order. Other statesor

federaljurisdictions may havesimilar laws.

Contactthe original equipment manufacturer, retailer, or dealer

to obtain a spark arrester designedfor the exhaust system

installed on this engine.

• Replacement parts must bethe sameand installed in the same

position asthe original parts.

Cleanand inspectthe sparkarresterasfollows:

1. To remove muffler heatshield (A) from muffler (B),

remove four screws that connect guard to muffler

bracket.

Removefour screws that attach sparkarrester screen

(c).

Inspect screenand obtain a replacementif torn,

perforated or otherwise damaged.DONOTusea

defective screen. If screen is not damaged, cleanit with

commercial solvent.

4. Reattachscreen and muffler guard.

AirCoolingSystem

Overtime debris may accumulate in cylinder cooling fins and

cannot be observedwithout partial engine disassembly. For

this reason,we recommendyou havean authorized Briggs &

Stratton service dealercleanthe cooling system (H) per

recommended intervals (seeMaintenanceSchedulein

beginning of Maintenancesection). Equallyimportant is to

keeptop of engine freefrom debris. See CleanDebris.

CarburetorAdjustment

Thecarburetor on this engine is low emission. It is equipped

with a non-adjustable idle mixture valve.Top speedhas been

set at the factory. If adjustment is required,seean

authorized Briggs & Stratton servicedealer.

_i, CAUTION Excessivelyhigh operating speeds increase

risk of injury and damageto generator.

Excessivelylow speedsimposea heavyload.

• DONOTtamperwith governedspeed.Generatorsupplies

correctratedfrequencyandvoltagewhenrunningatgoverned

speed.

• DONOTmodifygeneratorinanyway.

Storage

Thegenerator should be started at least once every seven

days and allowed to run at least 30 minutes. If this cannot be

done and you must store the unit for more than 30 days,use

the following guidelinesto prepare it for storage.

Generator Storage

• Cleanthe generator as outlined in Cleaning.

• Checkthat cooling air slots and openingson generator

are open and unobstructed.

Long Term Storage Instructions

Fuelcan becomestale when stored over 30 days.Stalefuel

causesacid and gum deposits to form in the fuel system or

on essentialcarburetor parts. To keepfuel fresh, use Briggs

& Stratton FRESHSTART® fuel stabilizer, availableasa

liquid additive or a drip concentrate cartridge.

Thereis noneed to drain gasolinefrom the engineif a fuel

stabilizer is added according to instructions. Runthe engine

for 2 minutes to circulatethe stabilizer throughout the fuel

system. The engine and fuel canthen be stored upto

24 months.

If gasoline in the engine hasnot beentreated with afuel

stabilizer, it must be drainedinto anapprovedcontainer. Run

the engine until it stops from lack of fuel. Theuse of a fuel

stabilizer in the storage container is recommendedto

maintain freshness.

_i, WARNING Fueland its vapors are extremely

flammable and explosive.

Fireor explosion can causesevereburns

or death.

WHENSTORINGFUELOREQUIPMENTWITHFUELINTANK

• Store awayfrom furnaces, stoves,water heaters,clothes dryers

or other appliancesthat have pilot light or other ignition source

becausethey can ignite fuel vapors.

WHENDRAININGFUEL

• Turn generator OFFand let it cool at least2 minutes before

removing fuel cap. Loosencap slowly to relievepressure in

tank.

• Drain fuel tank outdoors.

• Keepfuel awayfrom sparks, open flames, pilot lights, heat,and

other ignition sources.

• DO NOTlight acigarette or smoke.

ChangeEngineOil

While engine is still warm, drain oil from crankcase.Refill

with recommendedgrade.

OtherStorageTips

1. DONOTstore fuel from one seasonto another unless it

has beentreatedas describedin Long TermStorage

Instructions.

2. Replacefuel container if it starts to rust. Rustand/or

dirt in fuel can cause problems if it's usedwith this

unit.

3. Cover unit with a suitable protective cover that does not

retain moisture.

_i, WARNING Storagecovers can be flammable.

• DONOTplaceastoragecoverovera hotgenerator.

• Letequipmentcoolfor a sufficienttimebeforeplacingthecover

ontheequipment.

4. Store generator in clean, dry area.

18 BRIGGSandSTRATTON.COIVl

Troubleshooting

Problem

Engineis running,butno AC

outputis available.

Enginerunsgoodat no-loadbut

"bogs down"when loadsare

connected.

Enginewill not start;or starts

Cause

1. Oneof the circuit breakers is open.

2. Fault in generator.

3. Poor connection or defective cord set.

4. Connecteddeviceis bad.

1. Short circuit in a connectedload.

2. Enginespeed is too slow.

3. Generatoris overloaded.

4. Shorted generatorcircuit.

1. Rocker switch set to "Off".

2. FuelValveis in "Off" position.

3. Dirty air cleaner.

4. Out of fuel.

5. Stalefuel.

6. Spark plug wire not connectedto spark

plug.

Correction

1. Resetcircuit breaker.

2. Contact authorized servicefacility.

3. Checkand repair.

4. Connectanother devicethat is in good

condition.

1. Disconnect shorted electrical load.

2. Contact authorized servicefacility.

3. See Don't OverloadGeneratorin

Operationsection.

4. Contact authorized servicefacility.

1. Set switch to "On".

2. Turn fuel valve to "Open" position.

3. Cleanor replaceair cleaner.

4. Fill fuel tank.

5. Drain fuel tank and carburetor; fill with

fresh fuel.

6. Connectwire to spark plug.

and runsrough.

7. Bad spark plug.

8. Water in fuel.

9. Flooded.

10. Excessivelyrich fuel mixture.

7. Replacespark plug.

8. Drain gastank and carburetor; fill with

fresh fuel.

9. Wait 5 minutes and re-crank engine.

10. Contact authorized servicefacility.

Engineshutsdownwhen

running.

Enginelackspower.

Engine"hunts" or falters.

11. Intakevalve stuck open or closed.

12. Engine haslost compression.

Out of fuel.

1. Loadis too high.

2. Dirty air filter.

Carburetor is running too rich or too lean.

11. Contact authorized servicefacility.

12. Contact authorized servicefacility.

Fill fuel tank.

1. See Don't OverloadGeneratorin

Operationsection.

2. Replaceair filter.

Contact authorized servicefacility.

Warranties

California,U.S. EPA,andBriggs& Stratton

CorporationEmissionsControlWarranty

Statement

YourWarranty RightsAndObligations

The CaliforniaAir ResourcesBoard,U.S. EPA,and Briggs &

Stratton (B&S) are pleasedto explainthe emissions control

system warranty on your ModelYear 2008 and later

engine/equipment. In California,new small off-road engines

must be designed, built, and equipped to meet the State's

stringent anti-smog standards. B&S must warrantthe

emissions control system on your engine/equipmentfor the

periods of time listed below provided there hasbeen no

abuse, neglect,or improper maintenanceof your small off-

road engine.

Your emissions control system may include parts such as

the carburetor or fuel injection system, fuel tank, ignition

system, and catalytic converter. Also included may be hoses,

belts, connectors, sensors, and other emissions-related

assemblies.Wherea warrantable condition exists, B&S will

repair your engine/equipmentat no cost to you including

diagnosis, parts, and labor.

Manufacturer's WarrantyCoverage:

Small off-road engines arewarranted for two years. If any

emissions-related part on your engine/equipment is

defective,the part will be repaired or replacedby B&S.

Owner's WarrantyResponsibilities:

• As the small engine/equipment owner, you are

responsiblefor the performance of the required

maintenancelisted in your owner's manual. B&S

recommendsthat you retainall receipts covering

maintenanceon your engine/equipment, but B&S

cannot deny warranty solely for the lack of receiptsor

your failure to ensurethe performanceof all scheduled

maintenance.

• As the engine/equipmentowner, you should however

be awarethat B&Smay denyyou warranty coverageif

your engine/equipmentor a part hasfailed due to

abuse, neglect,improper maintenance,or unapproved

modifications.

• You are responsiblefor presentingyour

engine/equipmentto a B&Sdistribution center,

servicing dealer,or other equivalententity, as

applicable, assoon as a problem exists. Thewarranty

repairsshould be completed ina reasonableamount of

time, not to exceed30 days. If you haveany questions

regardingyour warranty rights and responsibilities, you

should contact B&Sat (414) 259-5262.

Briggs& StrattonEmissionsControlWarrantyProvisions

Thefollowing arespecific provisions relativeto your

Emissions Control Warranty Coverage.It is in addition to the

B&S enginewarranty for non-regulatedenginesfound in the

Operator's Manual.

1. Warranted Emissions Parts

Coverageunderthis warranty extends only to the parts

listed below (the emissions control systems parts) to

the extentthese parts were present on the engine

purchased.

a. FuelMetering System

• Cold start enrichment system (soft choke)

• Carburetor and internal parts

• Fuelpump

• Fuelline, fuel line fittings, clamps

• Fueltank, capand tether

• Carboncanister

b. Air Induction System

• Air cleaner

• Intake manifold

• Purge and vent line

Ignition System

• Spark plug(s)

• Magneto ignition system

CatalystSystem

• Catalyticconverter

• Exhaustmanifold

• Air injection system or pulse valve

e. Miscellaneous Items Used in Above Systems

• Vacuum,temperature, position, time sensitive

valvesand switches

• Connectors and assemblies

Length of Coverage

For a period of two years from dateof original

purchase, B&S warrants to the original purchaser and

eachsubsequent purchaserthat the engine is designed,

built, and equippedso asto conform with all applicable

regulations adoptedby the Air Resources Board;that it

is free from defects in material and workmanship that

could cause the failure of a warranted part; and that it

is identical in all material respects to the engine

described in the manufacturer's application for

certification. Thewarranty period beginson the datethe

engine is originally purchased.

20 BRIGGSandSTRATTON.COM

Page is loading ...

Briggs & Stratton 030448-0 Owner's manual

Brand: Briggs & Stratton

Model: 030448-0

Category: Power generators

Type: Owner's manual

This manual is also suitable for

PORTAbLE GENERATOR

Download PDF

report

in other languages

español: Briggs & Stratton 030448-0 El manual del propietario

Briggs & Stratton 030448-0 Owner's manual

This manual is also suitable for

Briggs & Stratton 030448-0 Owner's manual

in other languages

Related papers

Other documents