Megasat Mobile-Kit Assembly Instructions

Megasat
Brand
Megasat
Model
Mobile-Kit
Category
Electrical wallplates
Type
Assembly Instructions

Megasat Mobile-Kit

The Megasat Mobile-Kit is a mounting system for the following Megasat antennas:

  • Traveller-Man 2
  • Caravanman Kompakt 2
  • Caravanman Kompakt 2 Twin

The kit includes a base plate, four feet, eight fixing screws, and four screw sleeves.

To mount the kit, first remove the original mounting plate from the antenna. Then, attach the feet to the base plate using the fixing screws. The middle screw on each foot is a screw sleeve, into which the fixing screw of the base plate is screwed.

Finally, place the antenna on the mobile kit and fasten the base plate with the four fixing screws.

Megasat Mobile-Kit

The Megasat Mobile-Kit is a mounting system for the following Megasat antennas:

  • Traveller-Man 2
  • Caravanman Kompakt 2
  • Caravanman Kompakt 2 Twin

The kit includes a base plate, four feet, eight fixing screws, and four screw sleeves.

To mount the kit, first remove the original mounting plate from the antenna. Then, attach the feet to the base plate using the fixing screws. The middle screw on each foot is a screw sleeve, into which the fixing screw of the base plate is screwed.

Finally, place the antenna on the mobile kit and fasten the base plate with the four fixing screws.

Megasat Werke GmbH, Industriestraße 4a, D-97618 Niederlauer
Tel.: +49 (0) 9771 / 63 567-100, Fax: +49 (0) 9771 / 63 567-144, Email: [email protected], Internet: www.megasat.tv
• 1x Grundplatte
• 4x Standfüße
• 8x Befestigungsschrauben
• 4x Schraubhülse
Lieferumfang:
Mobil-Kit Montageanleitung
Befestigungsschrauben Montageplatte
Lösen Sie die vier Befestigungsschrauben
an der Grundplatte und entfernen Sie die
Aluminium-Montageplatte.
Hinweis:
Die original Montageplatte der Antenne wird
für das Mobil-Kit nicht benötigt!
1. Vorbereitung:
Nutzen Sie die beiliegenden Schrauben
und befestigen Sie die Standfüße an der
Montageplatte. Die mittlere Schraube ist
eine Schraub-Hülse, in der die Befestigungs-
schraube der Grundplatte eingedreht wird
(siehe Punkt 3).
Setzen Sie die Antenne auf das Mobil-Kit.
Befestigen Sie die Grundplatte wieder
mit den vier Befestigungsschrauben.
2. Montage des Mobil-Kits
3. Montage an der Antenne
Version: 1.0 (September 2019) // Technische Änderungen, Druckfehler und Irrtümer vorbehalten.
40,6 cm
40,9 cm
Das Mobil-Kit ist ausschließlich geeignet für folgende Antennen:
Traveller-Man 2 (Artikel-Nr. 1500185)
Caravanman Kompakt 2 (Artikel-Nr. 1500186)
Caravanman Kompakt 2 Twin (Artikel-Nr. 1500187)
WICHTIGER HINWEIS:
Befestigungsschrauben
Die folgende Montage des Mobil-Kits wird mit dem Traveller-Man 2 beschrieben.
Die Vorgehensweise beim Caravanman Kompakt 2 ist die gleiche.
Megasat Werke GmbH, Industriestraße 4a, D-97618 Niederlauer
Tel.: +49 (0) 9771 / 63 567-100, Fax: +49 (0) 9771 / 63 567-144, Email: [email protected], Internet: www.megasat.tv
• 1x base plate
• 4x feet
• 8x xing screws
• 4x screw sleeve
Delivery:
Mobil-Kit assembly instruction
xing screws mounting plate
Unscrew the four mounting screws on
the base plate and remove the aluminum
mounting plate.
Note:
The original mounting plate of the antenna
is not needed for the mobile kit!
The following installation of the mobile kit is described with the Traveller-Man 2.
The procedure for the Caravanman Kompakt 2 is the same.
1. Preparation:
Use the enclosed screws and fasten the feet
to the mounting plate. The middle screw is
a screw sleeve, in which the xing screw of
the base plate is screwed in (see point 3).
Place the antenna on the mobile kit. Fasten
the base plate again with the four fastening
screws.
2. Mounting the mobile kit
3. Mounting on the antenna
Version: 1.0 (September 2019) // Technical changes, misprints and errors reserved.
40,6 cm
40,9 cm
The mobile kit is only suitable for the following antennas:
Traveller-Man 2 (Article-No. 1500185)
Caravanman Kompakt 2 (Article-No. 1500186)
Caravanman Kompakt 2 Twin (Article-No. 1500187)
IMPORTANT NOTE:
xing screws
  • Page 1 1
  • Page 2 2

Megasat Mobile-Kit Assembly Instructions

Megasat
Brand
Megasat
Model
Mobile-Kit
Category
Electrical wallplates
Type
Assembly Instructions

Megasat Mobile-Kit

The Megasat Mobile-Kit is a mounting system for the following Megasat antennas:

  • Traveller-Man 2
  • Caravanman Kompakt 2
  • Caravanman Kompakt 2 Twin

The kit includes a base plate, four feet, eight fixing screws, and four screw sleeves.

To mount the kit, first remove the original mounting plate from the antenna. Then, attach the feet to the base plate using the fixing screws. The middle screw on each foot is a screw sleeve, into which the fixing screw of the base plate is screwed.

Finally, place the antenna on the mobile kit and fasten the base plate with the four fixing screws.

Download PDF
report

Ask a question and I''ll find the answer in the document

Finding information in a document is now easier with AI

in other languages

Related papers

Other documents