Kistler 2055A Owner's manual

Brand: Kistler

Model: 2055A

Type: Owner's manual

This manual is also suitable for

2053A

Instruction

Manual

2055A_002-860e-10.20

Correvit S-Motion DTI:

non-contact optical

sensors

Type 2055A..., 2053A...

Page 12055A_002-860e-10.20

The information in this manual is subject to change without

notice. To keep pace with technical advancement, Kistler

reserves the right to make improvements and changes

to the product without obligation to notify any person or

organization of such changes.

protected by various intellectual property rights. For more

details visit www.kistler.com. The Kistler Group includes

Kistler Holding AG and all its subsidiaries in Europe, Asia,

the Americas and Australia.

Kistler Group

Eulachstrasse 22

8408 Winterthur

Switzerland

Phone +41 52 224 11 11

info@kistler.com

Kistler Instrumente GmbH

Automotive Research & Test Division

Charlotte-Bamberg-Str. 12

35578 Wetzlar

Germany

Phone +49 6441 9282 0

info.de@kistler.com

www.kistler.com

Foreword

S-Motion DTI: non-contact optical sensors, Type 2055A..., 2053A...

2055A_002-860e-10.20Page 2

Contents

1. Introduction .................................................................................................................................4

2. Important remarks ......................................................................................................................5

2.1 For your safety ....................................................................................................................5

2.2 Disposal instructions for electrical and electronic equipment .............................................6

2.3 Software upgrades and updates .........................................................................................6

3. Product description ....................................................................................................................7

3.1 General ...............................................................................................................................7

3.2 Features .............................................................................................................................8

3.3 Application ..........................................................................................................................8

3.4 Accessories ........................................................................................................................8

4. Technical data ...........................................................................................................................10

4.1 Specications ...................................................................................................................10

4.2 Pin assignments ...............................................................................................................12

4.2.1 S-Motion DTI with standard ECU ........................................................................12

4.2.2 S-Motion DTI with small ECU ..............................................................................14

5. Mounting and connection ........................................................................................................15

5.1 Mounting options ..............................................................................................................15

5.2 Sensor mounting diagram ................................................................................................16

5.3 Coordinate systems ..........................................................................................................17

5.3.1 Body coordinate system .....................................................................................17

5.3.2 Horizontal coordinate system ..............................................................................17

5.3.3 Bandwidthorcut-ofrequency ............................................................................18

5.3.4 Filter setting and acquisition rate ........................................................................18

5.4 Mounting instructions ........................................................................................................19

5.4.1 Installing with magnetic holder ............................................................................19

5.4.2 Installing with suction holder ...............................................................................22

5.4.3 Installing the safety line .......................................................................................24

5.5 Connecting the sensor ......................................................................................................26

5.5.1 Standard ECU, Type 2055A... .............................................................................26

5.5.2 Small ECU, Type 2053A... ...................................................................................28

Page 32055A_002-860e-10.20

Total number of pages: 77

6. KiCenter Software .....................................................................................................................29

6.1 Toolbar ..............................................................................................................................29

6.1.1 Explanation of the buttons in the toolbar .............................................................30

6.2 S-Motion sensor settings ..................................................................................................32

6.2.1 Sensor node ........................................................................................................33

6.2.2 Measurement display ..........................................................................................34

6.2.3 Sensorconguration ...........................................................................................35

6.2.4 Digital output .......................................................................................................38

6.2.5 Analog output ......................................................................................................39

6.2.6 CAN Bus ..............................................................................................................40

6.2.7 Input channel settings .........................................................................................43

6.2.8 Device calibration ................................................................................................44

6.3 Firmware update ..............................................................................................................49

7. Troubleshooting ........................................................................................................................51

7.1 Cables and power supply .................................................................................................51

7.2 Status display and LED on sensor electronics .................................................................51

7.3 Illumination .......................................................................................................................51

7.4 Sensor lens (protection glass) ..........................................................................................51

7.5 Operating range ................................................................................................................52

7.6 Software ...........................................................................................................................52

7.7 CAN ..................................................................................................................................52

7.8 Environmental conditions .................................................................................................53

7.9 EMC interference ..............................................................................................................53

7.10 Service ..............................................................................................................................53

8. Appendix ....................................................................................................................................54

S-Motion DTI: non-contact optical sensors, Type 2055A..., 2053A...

2055A_002-860e-10.20Page 4

1. Introduction

Thank you for choosing a Kistler quality product. Read

this instruction manual carefully so that you can make full

use of your product's many features.

Where permitted by law, Kistler accepts no liability if this

instruction manual is disregarded or if products other than

those listed under accessories are used.

Kistler oers a wide range of measuring technology

products and complete solutions:

Piezoelectric sensors for the measurement of pressure,

force, torque, strain, acceleration, shock and vibration

Strain gauge sensor systems for the measurement of

force and torque

Piezoresistive pressure sensors and transmitters with

thecorrespondingampliers

Corresponding ampliers (charge ampliers,

piezoresistive ampliers, etc.), indicators and charge

calibrators

Devices for electronic control, monitoring and evalu-

ationunitsaswellasapplication-specicsoftwarefor

measurement technology

Data transmission modules (telemetry)

Kistler also designs entire measurement systems for

specicpurposes,forexample,intheautomotiveindustry,

in plastics processing and in biomechanics.

Our complete catalog provides an overview of our product

range. Detailed data sheets are available for nearly all

products.

Ifyoustillhaveanyspecicquestionsafterstudyingthese

instructions, the Kistler customer service is available

to you around the world and can also provide you with

competentadviceonapplication-specicproblems.

Important remarks

Page 52055A_002-860e-10.20

2. Important remarks

2.1 For your safety

Observe the following remarks before you commission

the device. Kistler accepts no responsibility for damages

that could arise from improper use of this product.

Prerequisite for the proper and safe use of the device

is that it be correctly stored, professionally installed and

commissioned, as well as operated as intended and

carefully maintained. Only persons who are familiar

with the installation, commissioning, operation and

maintenance of comparable devices and who possess the

qualicationsnecessaryforthegiventaskmayworkwith

the device.

Mounting a device on a vehicle invalidates the general

operating permit of the vehicle for use on public roads.

Observe the relevant legal requirements!

Do not look into the lamp; there is a risk of eye damage!

The lamp can become very hot; take this into account

when changing the lamp.

If the sensor is operated for a longer period of time, the

sensor head may become very hot, possibly resulting in

burn injuries. This applies in particular if the sensor is

operated in hot ambient conditions.

Do not use any defective or damaged devices.

Makenounauthorizedmodicationsandchangestothe

device and/or its accessories.

Improperinstallationofthedevicewillaectthesafetyof

the vehicle and the occupants! Install the device in such

a way that equipment necessary for the safety of the

vehicle is not impaired or disabled.

S-Motion DTI: non-contact optical sensors, Type 2055A..., 2053A...

2055A_002-860e-10.20Page 6

When connecting to the power supply, data acquisition

and evaluation systems and other usable components,

pay attention to the proper pin assignment and correct

operating voltage.

The sensor and/or sensor components could be damaged

if the sensor is operated for a long period of time in hot

ambientconditions.Switchothesensorifthevehicleis

not moved for a longer period of time.

Only use the original components included in the scope

of delivery.

Should it be necessary to use your own cables, always

pay attention to the correct pin assignment.

Kistler accepts no liability for damages caused by the use

of cables other than those supplied by Kistler.

For further information, please contact Kistler:

+49 6441 9282 0

info.de@kistler.com

2.2 Disposal instructions for electrical and electronic equipment

Waste electronic equipment must not be disposed of with

household waste. At the end of its service life, return the

device to the nearest electronic disposal point or contact

your Kistler sales outlet.

2.3 Software upgrades and updates

If Kistler supplies upgrades or updates for embedded

software, they must be installed.

Kistler assumes no liability for direct or consequential

damages caused by products whose embedded software

is not up-to-date.

Product description

Page 72055A_002-860e-10.20

3. Product description

3.1 General

Correvit S-Motion DTI sensors enable direct, slip-free

measurement of longitudinal and transverse speed as

well as slip angle in vehicle driving dynamics tests.

Due to their properties, the high-resolution variants

(S-Motion DTI HR) are particularly suitable for low speeds

(e.g. industrial trucks, parking tests).

Correvit S-Motion DTI sensors use the proven Correvit

technology. A new algorithm signicantly reduces the

signal noise. This algorithm and the high measurement

frequency of 500 Hz enable a minimal signal delay of 6

ms.

A built-in 5 Hz GPS receiver enables determination of

position data and time. The external magnetic antenna

allowsexibleandquickmountingonthevehicle.

Integrated accelerometers enable the determination

of additional measurands like longitudinal and trans-

verse acceleration of the vehicle. Integrated angular rate

sensors enable measurement of the pitch and roll angle

as well as the rotation around the vertical axis of the vehi-

cle.

Moreover, further signals such as leveled acceleration

or curve radius are already calculated inside the sensor.

A conversion of speed to any point of the vehicle, e.g.

center of gravity or rear axis is possible.

The output of these additional signals provides the option

to perform a large number of measurands required for

drivingdynamicsstandardtests.Thissimpliestheinstru-

mentation of the vehicle and minimizes application errors.

Correvit S-Motion DTI sensors produce unparalleled

accuracy on all standard testing surfaces, even under the

most challenging conditions. They feature high-quality

optical elements, the newest optoelectronical components

and state-of-the-art high-performance signal processing

based on DSP and FPGA’s. Speed and distance informa-

tion is updated at 500 Hz to track every highly dynamic

maneuver.

S-Motion DTI: non-contact optical sensors, Type 2055A..., 2053A...

2055A_002-860e-10.20Page 8

3.2 Features

Reduced signal noise of speed and slip angle

Low signal delay of 6 ms

Conversion of measurands to any point of the vehicle

Capable of detecting driving direction – forward or

backward

Lowadjustmenteortatthevehicle,shortersetup

time, no running-in procedure

Optional: high-resolution variants with improved optical

resolution

3.3 Application

High-precision, slip-free measurement of

Distance

Speed (x, y)

Side-slip angle

Acceleration and rotational speed

GPS position data and time

Pitch and roll angle

3.4 Accessories

Included accessories

Type 2055A... (standard) ordering no.

Connecting cables

USB, l = 1.8 m 55155609

CAN, l = 2 m 55155606

DTI, l = 0.5 m 55155607

ETH, l = 2 m 55155608

Power cable DTI sensors, l = 2 m 55155612

Distributor cables

IN ANA/CNT, 8 pin LEMO, l = 1m 55159202

OUT ANA, 10 pin LEMO, l = 1m 55159203

OUT DIG, 10 pin LEMO, l = 1 m 55175071

USB stick software + manuals 55158846

Halogen lamp, cold light 18012531

Tool to exchange the sensor lamp 55064735

Cranked wrench key 55065040

Hexagon wrench key, 6 kt 55063983

Cranked wrench key 55065078

Mini folding rule 55064207

Product description

Page 92055A_002-860e-10.20

Screw set 55082183

Transport case complete 55066876

GPS antenna 55137560

Included accessories

Type 2053A... (small) ordering no.

Connecting cables

USB, l = 1.8 m 55155609

DTI, l = 0.5 m 55155607

ETH, l = 2 m 55155608

Power cable DTI sensors, l = 2 m 55155612

USB stick software + manuals 55158846

Halogen lamp, cold light 18012531

Tool to exchange the sensor lamp 55064735

Cranked wrench key 55065040

Hexagon wrench key, 6 kt 55063983

Cranked wrench key 55065078

Mini folding rule 55064207

Screw set 55082183

Transport case complete 55066876

GPS antenna 55137560

Optional accessories

Type 2055A... / Type 2053A... ordering no.

Suction holder S-350 18012551

Magnet holder S-350 18012545

IR temperature sensor

100 °C tarmac, 5 m 18031593

S-Motion DTI: non-contact optical sensors, Type 2055A..., 2053A...

2055A_002-860e-10.20Page 10

4. Technical data

4.1 Specications

Performance specifications

Type 2053A...

(standard)

Type 2055A...

(small)

Speed 1)

S-Motion DTI km/h ±250 (400)

S-Motion DTI HR km/h ±125 (200)

Measurement accuracy 2) %FSO <±0.2

Distance resolution mm ≤1

Angle ° ±30

Angle resolution ° <±0.01

Measurement accuracy angle 2)

Typical ° <±0.1

Guaranteed ° <±0.2

Angular speed °/s ±300

Acceleration g ±18

Non-linearity

Angle speed %FSO ±0.15

Acceleration %FSO ±0.15

Measurement frequency Hz 500

Working distance / range mm 350 ±100

Signal outputs

Digital output 1 Vel pulses/m 1 ... 1,000/TTL no

Digital output 2 Velxpulses/m 1 ... 1,000/TTL no

Digital output 3 VelyHz/km/h 2 ... 200/TTL no

Digital output 4 angle Hz/° 6 ... 900/TTL no

Analog output 1, Vel 3) V –10 ... 10 no

Analog output 2, Velx 3) V –10 ... 10 no

Analog output 3, Vely 3) V –10 ... 10 no

Analog output 4, angle 3) V –10 ... 10 no

Signal inputs

Trigger TTL no

Analog 1+2 (16 Bit) V –10 ... 10 no

Counter kHz 0 ... 100/TTL no

Interfaces

CAN (Motorola/Intel) 2.0B no

USB (Full Speed) 2.0

Ethernet yes

DTI yes

Technical data

Page 112055A_002-860e-10.20

System specifications

Type 2053A...

(standard)

Type 2055A...

(small)

Power supply V 10 ... 28

Power consumption max. (at 12 V) W 35

Temperature range

Operation °C –25 ... 50

Storage °C –40 ... 85

Relative humidity (non condensing) % 5 ... 80

Degree of protection (cable mounted)

Sensor head IP67

Electronics IP40

Dimensions (LxWxH)

Sensor head mm 118x70x45

Electronics mm 175x125x95 175x125x65

Weight

Sensor head grams 600

Electronics grams 1,100 890

Shock g

50 half-sine

Vibration g

10 ... 150

Illumination halogen

1) S-Motion DTI: optionally calibrated up to 400 km/h

S-Motion DTI HR: optionally calibrated up to 200 km/h

2) Determined on test surface with distance >200 m

3) Presetting; in KiCenter, you can freely assign the analog outputs by activating the checkbox “Individual Output Enable”

S-Motion DTI: non-contact optical sensors, Type 2055A..., 2053A...

2055A_002-860e-10.20Page 12

4.2 Pin assignments

4.2.1 S-Motion DTI with standard ECU

Fig. 1: S-Motion DTI standard ECU,

connector view of front panel

Power/DTI, 8-pin LEMO 1B, connector

Pin Signal

1 internal use

2 internal use

3 internal use

4 internal use

5 Vin_Ext

6 Vin_Ext

7 GND_Ext

8 GND_Ext

ETH/USB, 7-pin LEMO 1B, socket

Pin Signal

1 TX+

2 TX–

3 RX+

4 RX–

5 USB D+

6 USB D–

7 GND

Technical data

Page 132055A_002-860e-10.20

CAN, 7-pin LEMO 0B, socket

Pin Signal

1 CAN high

2 CAN low

3 GND

4 GND

5 nc

6 nc

7 nc

OUT, 10-pin LEMO 1B, socket

Pin Signal

1 Ana_out 1

2 Ana_out 2

3 Ana_out 3

4 Ana_out 4

5 AGND

6 Dig_out 1

7 Dig_out 2

8 Dig_out 3

9 Dig_out 4

10 DGND

IN, 8-pin LEMO 1B, connector

Pin Signal

1 ANA_in 1

2 ANA_in 2

3 AGND

4 LB_in

5 Counter_in

6Pull-up(10kΩ)toVin_Ext

7 Vin_Ext

8 GND Ext

A description of the pin assignments for sensor connector

and GPS connector is not necessary for the intended use

of the sensor.

S-Motion DTI: non-contact optical sensors, Type 2055A..., 2053A...

2055A_002-860e-10.20Page 14

4.2.2 S-Motion DTI with small ECU

Fig. 2: S-Motion DTI small ECU,

connector view of front panel

Power/DTI, 8-pin LEMO 1B, connector

Pin Signal

1 internal use

2 internal use

3 internal use

4 internal use

5 Vin_Ext

6 Vin_Ext

7 GND_Ext

8 GND_Ext

ETH/USB, 7-pin LEMO 1B, connector

Pin Signal

1 TX+

2 TX–

3 RX+

4 RX–

5 USB D+

6 USB D–

7 GND

A description of the pin assignments for sensor connector

and GPS connector is not necessary for the intended use

of the sensor.

Mounting and connection

Page 152055A_002-860e-10.20

5. Mounting and connection

5.1 Mounting options

For optimum performance and accuracy, the mounting

distance between the bottom of the sensor (without splash

guard) and the road surface must be in the specied

range (see chapter 4.1).

Fig. 3: Possible mounting positions

longitudinal sensor type

350 mm 350 mm 350 mm

transverse sensor type

Note the mounting direction of the S-Motion DTI sensor:

longitudinal/transverse variant.

In case of rain or snow, mount the sensor at the front of

the vehicle. This will prevent the measurement from being

impacted by splashing water or snow.

No special running-in procedure is necessary!

S-Motion DTI: non-contact optical sensors, Type 2055A..., 2053A...

2055A_002-860e-10.20Page 16

5.2 Sensor mounting diagram

Fig. 4: Correvit S-Motion DTI sensor head dimensions

23 pin MIL plug

Mounting holes

Mounting and connection

Page 172055A_002-860e-10.20

5.3 Coordinate systems

5.3.1 Body coordinate system

Fig. 5: Body coordinate system

X-axis: forward direction of the car

Y-axis: perpendicular to the X-axis, left direction of the car

Z-axis: perpendicular to the X-axis, up direction of the car

5.3.2 Horizontal coordinate system

Fig. 6: Horizontal coordinate system

X-axis: the body X-axis projected to the horizontal plane

Y-axis: the body Y-axis projected to the horizontal plane

Z-axis: vertical up direction parallel to the gravity axis

S-Motion DTI: non-contact optical sensors, Type 2055A..., 2053A...

2055A_002-860e-10.20Page 18

5.3.3 Bandwidth or cut-o frequency

The cut-o frequency of a system is dened as the fre-

quency where the amplitude of the original signal is

reduced by factor 1/sqrt(2) = 0.707.

The bandwidth is the range between upper and lower cut-

ofrequency.

Usually, we are dealing with low-pass lters where low

frequency or DC signals pass uninuenced but higher

frequencies are blocked. In that case the bandwidth is

identicaltothecut-ofrequency.

In case of a sensor - as for example Correvit S-350 - the

main limitation will be the processor cycle rate.

AS-350 sensor with a processor rate of250 Hz and l-

ter deactivated has a bandwidth of approximately 110 Hz.

Theuseofamovingaveragelterwillreducetheband-

width. As a rule of thumb the following formula can be

used:bandwidth=110Hz*4ms/ltertime

On the other hand, without ltering the resolution of the

signals will decrease. So it is only possible to detect mea-

sure signals whose frequency is below the cut-o fre-

quency and whose amplitude is higher than the sensor

resolution.

5.3.4 Filter setting and acquisition rate

If the acquisition rate is lower than the processor rate of

the sensor, the data acquisition system will only pick sin-

gle values from the sensor. To prevent loss of information

andaliasingeectthemovingaveragelterofthesensor

shouldbeactivated.Theltertimeshouldbeatleastthe

time between two acquisition samples. For example, if the

acquisitionrateis100Hztheltertimeshouldbeatleast

10 ms. The same applies if the CAN send rate of the sen-

sor is reduced.

Page is loading ...

Kistler 2055A Owner's manual

Brand: Kistler

Model: 2055A

Type: Owner's manual

This manual is also suitable for

2053A

Download PDF

report

Kistler 2055A Owner's manual

This manual is also suitable for

Kistler 2055A Owner's manual

Related papers

Other documents