Operator's manual
English
STAND TruTool TF 350 (1B1)
2 Table of contents E493EN_03.DOC
Table of contents
1. Safety ..................................................................................3
2. Description .........................................................................3
2.1 Intended use ........................................................................3
2.2 Technical data .....................................................................3
3. Setting work .......................................................................4
3.1 Mounting the pedestal .........................................................4
3.2 Mounting the TruTool TF 350 ..............................................4
4. Operation............................................................................7
5. Maintenance .......................................................................8
6. Replacement parts.............................................................8
E493EN_03.DOC Safety 3
1. Safety
¾ Read the Operator's Manual for the machine as well as that of
the pedestal, in addition to the safety information (Material
number 125699), in their entirety and follow precisely the
instructions contained therein before starting up the machine.
¾ Adhere to the safety regulations in accordance with DIN VDE,
CEE, AFNOR and to the specific regulations of the country of
operation.
Warning
Risk of injury from the pedestal tipping over!
¾ Fasten pedestal securely to the floor.
Warning
Risk of injury through crushing of the hand!
¾ Hold workpiece with both hands.
¾ Do not place hands between the tool parts.
2. Description
2.1 Intended use
The pedestal is a mounting device for supporting the
TruTool TF 350 jointing press.
The use of the TruTool TF 350 machine is described in the
TruTool TF 350 Operator's manual.
2.2 Technical data
Values
Weight (without machine) Approx. 32 kg
Working height Approx. 1190 mm
Total height Approx. 1480 mm
Technical data
Table 1
4 Setting work E493EN_03.DOC
3. Setting work
3.1 Mounting the pedestal
Additional equipment, tools, material
• Drilling machine.
• 4 suitable plugs.
• 4 suitable screws.
1. Bore 4 holes in the floor with a drilling machine.
2. Insert plugs into the bore holes (e.g. HILTI HST M10x130/50).
3. Fasten pedestal to the floor with 4 screws.
3.2 Mounting the TruTool TF 350
The TruTool TF 350 jointing press must be mounted on the
pedestal.
1. Remove cover by loosening 10 screws.
2. Remove fastening device by loosening 6 screws.
Cover half removed
Mounting
Remove the fastening device
Fig. 32628
E493EN_03.DOC Setting work 5
3. Place the TruTool TF 350 into the fastening device on a work
surface.
4. Place movable clamps into the fastening device.
5. Put the two screws in place.
1
2
3
4
4
1 TruTool TF 350
2 2 Fastening devices
3 4 clamps
4 2 screws
6. Lower TruTool TF 350 with fastening device onto the pedestal.
7. Insert the six screws on both sides and tighten them.
Prepare fastening device
Fig. 36625
Bring the fastening device
onto the pedestal with
machines and align it
6 Setting work E493EN_03.DOC
7
4
6
5
31 2
1 Tripping button
2 Button for beam stroke
3 Gap
4 Pedestal
5 Bore holes
6 6 screws
7 TruTool TF 350
Note
A clearance between the button for triggering the beam stroke (3)
and the tripping button (1) of 0.5 to 1 mm is prescribed.
8. Tighten the clamp screws with socket head screwdriver in both
bore holes.
9. Mount the cover.
Fig. 42264
E493EN_03.DOC Operation 7
4. Operation
Warning
Risk of injury through crushing of the hand!
¾ Hold workpiece with both hands.
¾ Do not place hands between the tool parts.
Machining with the STAND TruTool TF 350
1. Hold workpiece with both hands in the TruTool TF 350 jointing
press.
2. Start up the jointing process with the foot switch.
Fig. 32627
8 Maintenance E493EN_03.DOC
5. Maintenance
Warning
Danger of injury due to improper repairs!
The device will then not function properly.
¾ Repair work may only be carried out by a qualified specialist.
Note
Only use original replacement parts and observe the information
on the rating plate.
6. Replacement parts
To ensure the correct and quick delivery of original parts and
wearing parts:
1. Specify the order number.
2. Enter further order data:
– Voltage data
– Number of pieces
– Machine type
3. Specify the complete shipping information:
– Correct address.
– Required delivery type (e.g. air mail, courier, express mail,
ordinary freight, parcel post).
4. Send the order to your TRUMPF representative. Refer to the
address list at the end of the document for TRUMPF service
addresses.
Ordering replacement parts
/
