Agria 3596 Owner's manual

Brand: Agria

Model: 3596

Type: Owner's manual

Page is loading ...

998 114-C 07.01 agria 0496 011; 3596 011; 3696 011; 4396 011; 5196 021; 5396 011; 5496 011 agria-Werke GmbH • D-74215 Möckmühl • Tel. 06298/39-0 • Telefax 06298/38111 • e-mail: info@agria.de • Internet: http://www.agria.de 3

User advice leaflet for

agria

Snow Plough Attachment

User notice n° 998 114-C 07.01

Before starting to use, read the User Advice leaflet

and respect the safety recommendations!

Assembly

Assembling and removing the snow plough on the basic

agria machine

Basic machine

Please read this leaflet for information on a particular

assembly.

Remote control

Œ Put the free end of the cord (21) into the hole on the

notched lever (22) and knot the end.

•Put the other end with the handle (15) towards the

rear within reach of the hands or attach it using the

attachment clip (14) on the handle.

Rollers

Ž Adjust the rollers (1) so that the blade only

just touches the ground . The snow plough

must slide on the rollers.

When the blade starts to become worn down,

adjust the rollers. Always check that it is

properly set before starting snow clearing.

Plastic blade

•

It is possible to add a plastic blade (K) below the steel

blade (S). Pierce the plastic blade (agria ref. 379 27) at the

top, alongside and flush with the steel blade.

Ballast

The bearing weight can be increased by increasing the

front ballast on the ballast-gate (4).

Snow chains

To improve the grip of the driving wheels, it is advisable

to use snow chains.

Snow plough

The snow plough has three

pivoting positions:

- central position

- pivoting to the left

- pivoting to the right

By pulling the cord handle,

move the snow plough into the

desired position. By leaning the

plough over slightly, the snow

can be cleared to the side.

Make sure that the stop button

is properly fitted into the correct

hole after pivoting and after

having released the handle.

After tpivoting, place the

handle on the plough handle or

attach it with the attachment clip.

Technical characteristics

Ref. Blade width Weight

0496 011 .............100 cm ....... 17,8 kg

3596 011 ...............80 cm ....... 36,2 kg

3696 011 .............100 cm ....... 42,8 kg

4396 011 ...............80 cm ....... 13,0 kg

5196 021 .............100 cm ....... 14,5 kg

5396 011 .............100 cm ....... 16,0 kg

5496 011 .............100 cm ....... 18,0 kg

3 pivoting positions , ............................

remote control: ....................................

respectively left, centered, right

Accessories

1 plastic blade .....................................

...................................ref. agria 486 63

Maintenance and

servicing

Grease all the moving parts,

especially:

- The movement around the

notched lever.

Before each assembly, lightly

coat the pivot support with

biodegrable grease.

Tighten the nuts and bolts

shortly after starting to use the

machine.

Maintenance

Carry out a thorough

cleaning.

Add a coat of varnish.

Grease all the moving parts

with biodegradable grease.

Spray all the exposed parts

with biodegradable rust

proofing.

2280_1

0496 011

3596 011

3696 011

4396 011

5196 021

5396 011

5496 011

Statement of EU conformity

In compliance with the European Union

Directive

We,

agria-Werke GmbH,

D-74215 Möckmühl/Württ,

state being fully responsible and that the

agria type Snow Plough Attachment:

0496 011; 3596 011; 3696 011;

4396 011; 5196 021;

5396 011; 5496 011

referred to in this statement is in

conformity with the basic

health and safety requirements

of European Union Directive 98/37/UE.

Möckmühl, on 15 October1999

i.V. Gregor Czaja

Quality Manager

i.V. Thomas Ilchmann

Research and Development Manager

Snow plough 0496 011

Assembly on Agria 400

Requires intermediate support ref.

0450 041.

Put the pivot support (2) into the hole

in the intermediary support (3) and block

it with the linch pin (4).

Connect the intermediary support with

the snow plough attached to the basic

machine

èè

Basic machine.

To improve snow clearing capacity, it

is better to add ballast (2) or the skip (16)

weighted with pebbles for example.

Removing is carried out in the reverse

sequence.

The intermediate support can be left

assembled on the snow plough.

Snow plough 0496 011

Assembly on agria 100 / 100R

Requires intermediate support ref.

0140 031.

Put the pivot support (2) in the hole of

the intermediary support (3) block it with

the linch pin (4).

Then connect the intermediate sup-

port to the snow plough assembled to the

square reception pipe (6) of the basic

machine and block it with the linch pin

(5).

Removing is carried out in the reverse

sequence.

The intermediate support may be left

assembled to the snow plough.

Snow plough

3596 011 or 3696 011

Assembling on agria 3500

or on 3600; 3600BM; 3900; 5800

ŒŒ

For the 3900 and 5800 the intermediate

support ref. 3940 041 is required.

Open the pivot screw (20) using an

angled hexagon key SW 8.

Bring the intermediate support (18) to the

pivot connector of the snow plough. Take

care that the pivot slots properly into the

notch of the pivot connector. Tighten the

pivot screw (20). Block with the hexago-

nal bolt (19).

ŒŒ

••

•

ŽŽ

Ž Change the garden tractor to

front coupling for a mounted implement.

To assemble, lower the prop (2), raise

the pivot connector (4) until it is in the

horizontal position and insert the linch

pin (3) under the pivot connector through

the transversal prop hole.

Remove the protective cap (17) from

the pivot connector.

Bring the basic machine to the snow

plough and connect it with the implement

coupling - tighten the bolt.

èè

Basic machine

Remove the prop (2) and secure with

the linch pin at the top by the transversal

hole in the prop.

Removing is carried out in the reverse

sequence.

Put the protective cap (17) back on

the pivot connector.

Snow plough 5496 011

Assembly on agria 5400

with spider wheel cutter

Remove the cutting bar.

Put the screw bolt into the

reception hole in the cutting bar.

Assemble the bolts (5) and

washers (6) and tighten.

Removing is carried out in the re-

verse sequence.

Snow plough 5496 011

Assembling on the agria 5400

with oscilating double-bladed

cutter

Requires an intermediate support

ref. 5450 041.

Assemble the intermediate sup-

port (4) put the bolts (6) and washers

(6) on the screw bolts of the snow

plough and tighten.

Dismantle the cutting bar, the

centering bushes (7) remaining in

their reception hole.

Assemble the snow plough with

the intermediate support in the

reception hole of the cutting bar with

screws (2) and washers (3) and

tighten.

Removing is carried out in the re-

verse sequence.

The intermediate support may be

left assembled on the snow plough.

Snow plough

5196 021

Snow plough

4396 011

Assembly on agria 5100

Rabbit and 4300

Remove the cutting bar.

Put the pivot support (2) into

the reception hole of the cutting

bar and block with the linch pin

(4) in the transversal hole.

Removing is carried out in the

reverse sequence.

Snow plough

5396 011

Assmbly on agria 5300

Dismantle the cutting bar.

Put the pivot support (2) into

the reception holeof the cutting

bar(3).

Close the bolt (4) or else

assemble the transversal

screw (6) with the washer (5)

and tighten.

Removing is carried out inthe

reverse sequence.

Type 3500

Types 3600 and 3600BM

Types 3900 and 5800

Technical safety advice

Before assembling or removing the snow plough as well as before

starting on maintenance or servicing work, stop the machine's engine!

Wear heavy duty shoes!

Be careful of crushing or churning up the ground when turning the snow plough!

Take care to match the speed to the specific working conditions encountered: if

the machine hits an obstruction, the shock of the impact may injure the driver.

•

8,5 - 9 mm

•

Page is loading ...

Agria 3596 Owner's manual

Brand: Agria

Model: 3596

Type: Owner's manual

Download PDF

report

in other languages

français: Agria 3596 Le manuel du propriétaire
Deutsch: Agria 3596 Bedienungsanleitung
Nederlands: Agria 3596 de handleiding

Agria 3596 Owner's manual

Agria 3596 Owner's manual

in other languages

Related papers

Other documents