Einhell Classic GC-RS 2540 User manual

GC-RS 2540

Art.-Nr.: 34.306.20 I.-Nr.: 11015

7

D Originalbetriebsanleitung

Gartenhäcksler

GB Original operating instructions

Electric quiet shredder

F Instructions d’origine

Hacheuse electrique silencieuse

S Original-bruksanvisning

Tystgående elektrisk

kompostkvarn

NL Originele handleiding

Elektrische stille hakselaar

FIN Alkuperäiskäyttöohje

Hiljainen sähkösilppuri

Anl_GC_RS_2540_SPK7.indb 1Anl_GC_RS_2540_SPK7.indb 1 15.07.15 10:3115.07.15 10:31

Page is loading ...

GB

- 14 -

Danger!

When using the equipment, a few safety pre-

cautions must be observed to avoid injuries and

damage. Please read the complete operating

instructions and safety regulations with due care.

Keep this manual in a safe place, so that the in-

formation is available at all times. If you give the

equipment to any other person, hand over these

operating instructions and safety regulations as

well. We cannot accept any liability for damage

or accidents which arise due to a failure to follow

these instructions and the safety instructions.

1. Safety regulations

The corresponding safety information can be

found in the enclosed booklet.

Danger!

Read all safety regulations and instructions.

Any errors made in following the safety regula-

tions and instructions may result in an electric

shock, ﬁ re and/or serious injury.

Keep all safety regulations and instructions

in a safe place for future use.

Description of the warning sign (see Figure

2) on the machine

1: Important! Read the operating instructions

and follow the warnings and safety instruc-

tions

2: Take care when the blades are rotating. Do

not put your hands or feet into openings when

the machine is running.

3: Important! Keep other persons and animals

away from the danger zone.

4: Important! Protect the machine from the

damp and never expose it to rain.

5: Important! Always wear safety goggles, ear

muﬀ s, protective gloves and heavy-duty work

clothes!

6: Always set the ON/OFF switch to OFF and

pull the power plug out of the socket-outlet

before doing any work on the shredder, e.g.

cleaning the shredder and making adjust-

ments, or if

the power cable becomes damaged.

7. Changeover switch: For a description of the

changeover switch see point 6.3

8: Explanation of the lever for adjusting the

counter blade:

Turning clockwise reduces the distance bet-

ween the cutting unit and the counter blade.

Turning counter-clockwise increases the

distance between the cutting unit and the

counter blade.

2. Layout and items supplied

2.1 Layout (Fig. 1)

1. Funnel

2. Motor circuit breaker switch

3. On/Oﬀ switch

4. Reverse running switch

5. Power plug

6. Knob for setting the counter blade

7. Base frame

8. Discharge opening

2.2 Items supplied

Please check that the article is complete as

speciﬁ ed in the scope of delivery. If parts are

missing, please contact our service center or the

sales outlet where you made your purchase at

the latest within 5 working days after purchasing

the product and upon presentation of a valid bill

of purchase. Also, refer to the warranty table in

the service information at the end of the operating

instructions.

•

Open the packaging and take out the equip-

ment with care.

•

Remove the packaging material and any

packaging and/or transportation braces (if

available).

•

Check to see if all items are supplied.

•

Inspect the equipment and accessories for

transport damage.

•

If possible, please keep the packaging until

the end of the guarantee period.

Danger!

The equipment and packaging material are

not toys. Do not let children play with plastic

bags, foils or small parts. There is a danger of

swallowing or suﬀ ocating!

•

Original operating instructions

•

Safety instructions

Anl_GC_RS_2540_SPK7.indb 14Anl_GC_RS_2540_SPK7.indb 14 15.07.15 10:3115.07.15 10:31

GB

- 15 -

3. Proper use

This electric garden refuse shredder is designed

only for shredding organic garden waste. Place

biologi-cally degradable material, e.g. leaves,

branches, dead ﬂ owers etc., into the loading fun-

nel inlet.

The equipment is to be used only for its prescri-

bed purpose. Any other use is deemed to be a

case of misuse. The user / operator and not the

manufacturer will be liable for any damage or inju-

ries of any kind caused as a result of this.

Please note that our equipment has not been de-

signed for use in commercial, trade or industrial

applications. Our warranty will be voided if the

machine is used in commercial, trade or industrial

businesses or for equivalent purposes.

4. Technical data

Voltage: ......................................... 230 V ~ 50 Hz

Power rating: ........................... 2500 W (S6-40%)

..........................................................2000 W (S1)

Cutting unit idling speed ..........................40 min

-1

Branch diameter: ..............................max. 40 mm

L

pA

sound pressure level: ...................... 80 dB (A)

K uncertainty .......................................... 3 dB (A)

L

WA

sound power level: ......................... 93 dB (A)

Weight: .....................................................25.1 kg

Protection class:.................................................. I

Keep the noise emissions and vibrations to a

minimum.

•

Only use appliances which are in perfect wor-

king order.

•

Service and clean the appliance regularly.

•

Adapt your working style to suit the appliance.

•

Do not overload the appliance.

•

Have the appliance serviced whenever ne-

cessary.

•

Switch the appliance off when it is not in use.

•

Wear protective gloves.

Caution!

Residual risks

Even if you use this electric power tool in

accordance with instructions, certain resi-

dual risks cannot be rules out. The following

hazards may arise in connection with the

equipment’s construction and layout:

1. Lung damage if no suitable protective dust

mask is used.

2. Damage to hearing if no suitable ear protec-

tion is used.

3. Health damage caused by hand-arm vib-

rations if the equipment is used over a pro-

longed period or is not properly guided and

maintained.

5. Before starting the equipment

Before you connect the equipment to the mains

supply make sure that the data on the rating plate

are identical to the mains data.

Warning!

Always pull the power plug before making

adjustments to the equipment.

Assembly (Fig. 3)

•

Take all the parts out of the packaging.

•

Fit the chassis to the housing using the four

lock nuts (Item 2).

•

Fit the axle (Item 3) to the chassis using the

two M6 x 50 screws (Item 4) and nuts (Item

2).

•

Push the wheels (Item 5) onto the axle.

•

Secure the wheel cover (Item 6) on the axle

using a hammer.

•

Press the wheel caps onto the wheels.

6. Operation

Please observe the statutory regulations gover-

ning noise abatement during operating times,

which may diﬀ er from town to town.

6.1 Mains connection

Connect the device with an extension lead con-

nected to the power plug (Fig. 1/Item 7). Be sure

to observe the relevant information in the safety

instructions.

Anl_GC_RS_2540_SPK7.indb 15Anl_GC_RS_2540_SPK7.indb 15 15.07.15 10:3115.07.15 10:31

GB

- 16 -

6.2 ON/OFF switch (Fig. 1/Item 3)

•

Press the green knob to switch on the shred-

der.

•

Press the red knob to switch it off.

Note: The device has a zero voltage switch. This

prevents the device restarting unintentionally after

a power failure.

6.3 Direction selection switch (Fig.1/Item 4)

Important! The switch for selecting the direc-

tion of rotation can only be moved when the

shredder is switched oﬀ .

Position “⇓”

The material is automatically drawn in by the bla-

de and shredded.

Position “⇑”

The blade rotates in the opposite direction to

release jammed material. After moving the selec-

tor switch to the “⇑” position, press and hold the

green knob of the ON/OFF switch. The blade will

start to rotate in the opposite direction. As soon

as you release the ON/OFF switch, the shredder

will stop automatically.

Important! Always wait until the shredder has

reached a standstill before you switch it on

again.

Note: If the switch for selecting the direction of

rotation is in its center position, the motor will not

start.

Large items or pieces of wood will be discharged

both in the cutting and in the release direction

after the blade has been started and reversed

several times.

6.4 Motor protection (Fig. 1 / Item 2)

An overload (for example if the blade is jammed)

will cause the machine to cut out after a few

seconds. To protect the motor from damage the

motor protection switch stops the power supply

automatically. Wait for at least one minute before

you press the reset knob so that you can restart

the machine.

Then press the ON/OFF switch.

If the blade becomes jammed, turn the switch for

selecting the direction of rotation to the left to po-

sition “⇑” before you switch on the shredder again.

6.5 Practical tips

•

Be sure to observe the safety instructions

(see supplied booklet).

•

Wear work gloves, goggles and ear protec-

tion.

•

Fill in the material you want to shred at the

funnel on the side with the larger opening

(Fig. 1/Item 1).

•

The material is drawn into the shredder auto-

matically. CAUTION! Long pieces of material

projecting out of the funnel inlet may whiplash

when it is drawn in – keep a safe distance

between yourself and the machine.

•

Judge the quantity of material which you put

into the funnel inlet so that the funnel does

not clog.

•

If you want to shred withered, damp material

that has been lying in the garden for several

days, alternate between putting in this materi-

al and branches. This will help to prevent the

loading funnel becoming clogged with materi-

al.

•

Do not shred soft waste (e.g. kitchen waste) –

put it straight in the compost box.

•

Entangled branches and leaves should be tho

roughly shredded before loading any more

material.

•

Do not allow the discharge opening to be-

come clogged with shredded material – risk

of pile-ups.

•

Do not cover the ventilation slits.

•

Do not place heavy material or thick bran-

ches into the machine continuously. This may

cause the blade to jam.

•

Use a plunger or hook to remove jammed ob-

jects from the funnel or discharge openings.

Important: The material will be crushed, mashed

and shredded by the cutting unit, thus accelera-

ting the decomposition process for composting.

6.6 Adjusting the counter blade (Fig. 4)

The counter blade and cutting unit are perfectly

adjusted at the factory. Only if it suﬀ ers wear does

the counter blade require adjustment (switch the

machine on for this purpose). To ensure the best

possible results from your shredder, the gap bet-

ween the counter blade (item B) and the shred-

ding blade (item A) should be approx. 0.50 mm.

There is an adjustment device on the right-hand

side of the plastic housing for this purpose. Turn

the knob clockwise so that the screw (item C)

moves towards the shredding blade. After a half-

turn the counter blade will have moved 0.50 mm

closer to the shredding blade. After completing

Anl_GC_RS_2540_SPK7.indb 16Anl_GC_RS_2540_SPK7.indb 16 15.07.15 10:3115.07.15 10:31

GB

- 17 -

this adjustment check whether the blade produ-

ces the desired results.

IMPORTANT: If the shredding blade touches the

counter blade, it will cut it and small metal chips

may fall out of the discharge opening. This is not

a fault, but it must only be adjusted as much as

necessary since otherwise the counter blade will

suﬀ er premature wear.

7. Replacing the power cable

Danger!

If the power cable for this equipment is damaged,

it must be replaced by the manufacturer or its

after-sales service or similarly trained personnel

to avoid danger.

8. Cleaning, maintenance and

ordering of spare parts

Danger!

Always pull out the mains power plug before star-

ting any cleaning work.

8.1 Maintenance and storage

•

Clean the machine regularly. This will help to

keep the machine in good working order and

is the basis for a long working life.

•

Keep the vent slots clean while you work.

•

Clean the plastic body and other plastic parts

with a mild household cleaning agent and

a damp cloth. Do not use any aggressive

agents or solvents for cleaning purposes.

•

Never clean the shredder by spraying with

water.

•

Prevent water getting inside the machine at

all cost.

•

Check the chassis securing screws from time

to time to ensure that they are tight.

•

If you do not intend to use the shredder for a

lengthy period, protect it from corrosion using

environmentally friendly oil.

•

Store the device in a dry room.

•

Store the device out of reach of children.

8.2 Ordering replacement parts:

Please quote the following data when ordering

replacement parts:

•

Type of machine

•

Article number of the machine

•

Identification number of the machine

•

Replacement part number of the part required

For our latest prices and information please go to

www.isc-gmbh.info

9. Disposal and recycling

The equipment is supplied in packaging to pre-

vent it from being damaged in transit. The raw

materials in this packaging can be reused or

recycled. The equipment and its accessories are

made of various types of material, such as metal

and plastic. Never place defective equipment in

your household refuse. The equipment should

be taken to a suitable collection center for proper

disposal. If you do not know the whereabouts of

such a collection point, you should ask in your

local council oﬃ ces.

10. Storage

Store the equipment and accessories in a dark

and dry place at above freezing temperature. The

ideal storage temperature is between 5 and 30

°C. Store the electric tool in its original packaging.

Anl_GC_RS_2540_SPK7.indb 17Anl_GC_RS_2540_SPK7.indb 17 15.07.15 10:3115.07.15 10:31

GB

- 18 -

11. Troubleshooting

Fault Possible cause Remedy

The motor does not

start

- Power failure

- Motor circuit breaker has been trig-

gered

- The switch for selecting the direc-

tion of rotation is in its center positi-

on.

- Check the mains lead, plug and

fuse.

- Press the Reset button (see point

6.4)

- Set the direction of rotation on the

switch

Material is not

drawn in by the

shredder

- The shredding blade is running in

reverse.

- Material blockage in the ﬁ lling fun-

nel

- The shredding blade is jammed

- Change the direction of rotation.

- Change the direction of rotation

and pull the material out of the fun-

nel. Feed in thick branches again

so that the blade does not immedi-

ately engage again in the notches it

previously cut.

- Change the direction of rotation.

The blade will now release the jam-

med material.

The material is not

shredded properly

- The counter blade is not set cor-

rectly.

- Adjust the counter blade. See sec-

tion 6.6 on how to do so.

Anl_GC_RS_2540_SPK7.indb 18Anl_GC_RS_2540_SPK7.indb 18 15.07.15 10:3115.07.15 10:31

GB

- 19 -

For EU countries only

Never place any electric power tools in your household refuse.

To comply with European Directive 2012/19/EC concerning old electric and electronic equipment and

its implementation in national laws, old electric power tools have to be separated from other waste and

disposed of in an environment-friendly fashion, e.g. by taking to a recycling depot.

Recycling alternative to the return request:

As an alternative to returning the equipment to the manufacturer, the owner of the electrical equipment

must make sure that the equipment is properly disposed of if he no longer wants to keep the equipment.

The old equipment can be returned to a suitable collection point that will dispose of the equipment in

accordance with the national recycling and waste disposal regulations. This does not apply to any ac-

cessories or aids without electrical components supplied with the old equipment.

The reprinting or reproduction by any other means, in whole or in part, of documentation and papers

accompanying products is permitted only with the express consent of the iSC GmbH.

Subject to technical changes

Given unfavorable conditions in the power supply the equipment may cause the voltage to drop tem-

porarily. If the supply impedance “Z” at the connection point to the public power supply exceeds 0.329 Ω

it may be necessary to take further measures before the equipment can be used as intended from this

power supply. If necessary, you can ask your local electricity supply company for the impedance value.

Anl_GC_RS_2540_SPK7.indb 19Anl_GC_RS_2540_SPK7.indb 19 15.07.15 10:3115.07.15 10:31

GB

- 20 -

Ser vice information

We have competent service partners in all countries named on the guarantee certiﬁ cate whose contact

details can also be found on the guarantee certiﬁ cate. These partners will help you with all service re-

quests such as repairs, spare and wearing part orders or the purchase of consumables.

Please note that the following parts of this product are subject to normal or natural wear and that the

following parts are therefore also required for use as consumables.

Category Example

Wear parts* Roller

Consumables* Counter blade (pressure plate)

Missing parts

* Not necessarily included in the scope of delivery!

In the eﬀ ect of defects or faults, please register the problem on the internet at www.isc-gmbh.info. Ple-

ase ensure that you provide a precise description of the problem and answer the following questions in

all cases:

•

Did the equipment work at all or was it defective from the beginning?

•

Did you notice anything (symptom or defect) prior to the failure?

•

What malfunction does the equipment have in your opinion (main symptom)?

Describe this malfunction.

Anl_GC_RS_2540_SPK7.indb 20Anl_GC_RS_2540_SPK7.indb 20 15.07.15 10:3115.07.15 10:31

GB

- 21 -

Warranty cer tiﬁ cate

Dear Customer,

All of our products undergo strict quality checks to ensure that they reach you in perfect condition. In the

unlikely event that your device develops a fault, please contact our service department at the address

shown on this guarantee card. You can also contact us by telephone using the service number shown.

Please note the following terms under which guarantee claims can be made:

1. These warranty terms regulate additional warranty services, which the manufacturer mentioned

below promises to buyers of its new products in addition to their statutory rights of guarantee. Your

statutory guarantee claims are not aﬀ ected by this guarantee. Our guarantee is free of charge to

you.

2. The warranty services cover only defects due to material or manufacturing faults on a product which

you have bought from the manufacturer mentioned below and are limited to either the rectiﬁ cation of

said defects on the product or the replacement of the product, whichever we prefer.

Please note that our devices are not designed for use in commercial, trade or professional applica-

tions. A guarantee contract will not be created if the device has been used by commercial, trade or

industrial business or has been exposed to similar stresses during the guarantee period.

3. The following are not covered by our guarantee:

- Damage to the device caused by a failure to follow the assembly instructions or due to incorrect

installation, a failure to follow the operating instructions (for example connecting it to an incorrect

mains voltage or current type) or a failure to follow the maintenance and safety instructions or by ex-

posing the device to abnormal environmental conditions or by lack of care and maintenance.

- Damage to the device caused by abuse or incorrect use (for example overloading the device or the

use or unapproved tools or accessories), ingress of foreign bodies into the device (such as sand,

stones or dust, transport damage), the use of force or damage caused by external forces (for ex-

ample by dropping it).

- Damage to the device or parts of the device caused by normal or natural wear or tear or by normal

use of the device.

4. The guarantee is valid for a period of 24 months starting from the purchase date of the device. Gu-

arantee claims should be submitted before the end of the guarantee period within two weeks of the

defect being noticed. No guarantee claims will be accepted after the end of the guarantee period.

The original guarantee period remains applicable to the device even if repairs are carried out or

parts are replaced. In such cases, the work performed or parts ﬁ tted will not result in an extension

of the guarantee period, and no new guarantee will become active for the work performed or parts

ﬁ tted. This also applies if an on-site service is used.

5. Please report the defective device on the following internet address to register your guarantee claim:

www.isc-gmbh.info. If the defect is covered by our guarantee, then the item in question will either be

repaired immediately and returned to you or we will send you a new replacement device.

Of course, we are also happy oﬀ er a chargeable repair service for any defects which are not covered by

the scope of this guarantee or for units which are no longer covered. To take advantage of this service,

please send the device to our service address.

Also refer to the restrictions of this warranty concerning wear parts, consumables and missing parts as

set out in the service information in these operating instructions.

Anl_GC_RS_2540_SPK7.indb 21Anl_GC_RS_2540_SPK7.indb 21 15.07.15 10:3115.07.15 10:31

Page is loading ...

Einhell Classic GC-RS 2540 User manual

Einhell Classic GC-RS 2540 User manual

in other languages

Related papers

Other documents