Notice .............................................................................2
User Guide ......................................................................3
Playable Disc .................................................................6
Basic Operations ..................................................................13~28
Installation .................................................................. 40
Characteristics And Specifications .............................. 41
M P3 Functions ............................................................. 29p
Front Panel's Diagram .................................................... 7
Remote Control's Diagram............................................... 8
Function Instructions................................................9~12
Troubleshooting .....................................................38~39
The Remote Control uses and maintains......................... 4
Table of Contents
1
Touch screen function introduction.........................30~37
Disc Handling And Maintenance..........5
Disc Handling And Maintenance .....................................5
2
Notice
Important prevention measure
Please read the entire instruction Manual about your monitor and preserve properly
it, by win prepare later to consult.
1. Before operating this monitor , please read this instruction manual carefully.
2. Please preserve the instruction manual in convenient place, in order to consult
sequence of operation and security information.
3. Please pay more attention to the instruction manual each warning, and strictly
carries on the operation according to the instruction.
4. Other people except have read and grasped the operation explanation,
otherwise, do not let him use this system.
5. Do not install the monitor in which may cause:
A. Block off the driver s sightline.
B. Affects the vehicles any operating system or the security function
performance (including the button of the security aerocyst and caution light),
or interrupts the driver safe driving the position.
'
6. If operates this monitor to disperse your attention. Causes you are unable to
drive vehicles safely. Please observe the safe driving rule and pay attention to all
present traffic regulations, if you are operating system or reading the display in
trouble. Please park your car safely, then make with the necessary ajudgement.
7. Please remember to tie the safety belt when you driving, otherwise, if the
accident has happened. The injured degree will intensify.
8. Do not wear the earphone when you driving.
9. To ensure safety. Do not use some function when the brake is pulled up and the
vehicle is driving.
10. Do not turn up the volume too high. You can t hear the outer activity. '
!!
CAUTION
Do not install the vehicles which have no ACC function.
!!
CAUTION
Don t try installing or repairing your monitor . If you have no training about
electronic setup and car fittings, and who have no relational experiences. You
will be injured by electric shock or other danger.
'
!!
CAUTION
In order to avoid the accident and break the relational law. Do not use the display
monitor which the driver can be watching with this unit.
In order to avoid the accident has happened, and break the relational law. Do not
use the front DVD function when driving, and the back monitor should not install
it in which separate the driver s attention.
In some country or states, even if the driver or others, watching image from the
monitor will break the law. In similar area, must keep the rules and do not use the
DVD function.
'
41
CHARACTERISTICS
Characteristics And Specification
AM
Frequency range ( Europe )....................................................................... 522-1620KHz
Intermediatef requency.. .................................................................................... 450KHz
Practicalityn eat (S/N 20dB) ................................................................... lessth an4 8dB
Practicality neat (S/N 30dB) .................................................................. less than 22dB
Stereo separation .................................................................................. more than 25dB
FM
Intermediate frequency...................................................................................... 10.7MHz
Frequency range( America )....................................................................... 530-1710KHz
Frequency range ( Europe/Aust )........................................................... 87.5-108.0MHz
Frequency range( America )................................................................... 87.5-107.9MHz
Frequency range ( Aust )........................................................................... 5 22-1710KHz
Power .............................................................................................. DC12-13.8V, -earth
Dimensions.. ................................................................... 178(L)X158(W)X100.5(H)mm
TFT LCD Monitor
Liquid screen size.............................................................6.5 inch(Diagonal)
Display area...........................................................137.52(W) 77.22(V)mm
LCD dimension ............................................. 154.4(W)X92.6(H)X5.90(D)mm
Display format ............................................................ 480X(R,G,B)X234 dot
Specifications
NOTICE: The specification and design of this product are subject to changes
without prior notice.
3
User Guide
About unit
!!
Notice
A. This unit is used at the 13.8V DC ground. In the condition of the negative
ground connect with the metal body of car, so it is safe to operate.
B. Fix the unit in the steady parts. If you parked your car to direct the sunlight wait
until the temperature in the car becomes normal before operating the unit.
C. If this unit is out of order. Please shut off the power sources immediately and
contact with authorized repairman in time. Do not disassemble it by yourself.
D. Please forgive us that we are irresponsible for the damages by your own defect.
Protect LCD monitor
When this unit does not use in long time. Do not expose the LCD monitor to direct
sunlight. Otherwise, it will cause the function out of gear.When use the mobile
phone, please keep away from the monitor, so that video signal was interrupted
decause of spot, color stripe, etc.
!!
Notice
A. When your hands have sweat, water.
B. When your hands have dirt.
Do not touch the monitor to avoid it was damaged and cause the operating can t
control.
'
RESET MPU
Press RESET button to reset MPU to
default MPU must reset as following
situation:
When finished the installation before
use this unit first.
If this unit can t operate normally.
When the monitor appears
exceptionally or the error message.
''
'
1. Turn off the Ignition switch.
2. Use the pen point or other edgily tools to press.
Car back video input function
This unit includes car back video input function. (When car back camera connects
this player), during the operation of car backing, this player changes from play
mode to car back video input mode automatically.
Then the screen shows you back view, it protects you more safely.
40
CAUTION:
2. The location of the player must not obstruct the driver .
4. Follow the player connecting diagram, using the appendixes provided with
the unit.
1. Always use an experienced installation technician.
3. Do not install the player in excessive dusty, shakable, high-temperature
or humid condition.
Note : these conditions will adversely affect the player s operation.
,
Installation
Hex. Bolt
Body
Flexible washer
Car panel
Screw
Flat washer
Mounting metal bar
Hex. nut
Unit
Install the screw
Install the bracket
Note:Maybe some camera lens can t match with this monitor,so it will appear
horizontal line on picture.Only need press 9P/N button over 2 seconds on
remote control to set system match in 3 seconds,then solve this question.
'
Press RESET
4
The Remote Control uses and maintains
Install battery
Slide out the battery seat from the back of remote control, then according to
anode and negative direction to insert the battery.
When use it first. Please pull out film which the battery protrudes.
3V
+
3V
+
To prize the battery tray with the tip tool.
Pull out the battery tray and insert the battery +
towards up.
After installed the battery to push back the tray.
!!
CAUTION
Please keep the battery away from the children. If the battery was pushed back
by him. Please see a doctor at once.
!!
CAUTION
Only use a 3V lithium battery.
The remote control does not use in one month at least, please take out the
battery.
Do not electricize to the battery, tears down, heats up or abandons it in the fire.
Do not operate the battery with metal tool.
Do not store the battery with metal material.
If the battery leak liquid, please wipe it off and install the new battery.
Deal with the used battery. To obey the local government laws and regulations
of your country or the environment public organization s rules. '
Use remote control
The remote control operation aimed the front panel. The remote control cant
work normally to direct the sunlight.
'
!!
CAUTION
Do not keep the remote control to direct the high temperature or sunlight.
Do not keep the remote control falling the floor. So that it was clipped in below of
the brake or gun.
39
Troubleshooting
The troubles in DVD playing
Trouble
Reason
Measure
Fails to
dialogue
language and
subtitle
language
The playing DVD has not
multi-lingual record content.
If the disc does not record
muti-lingual, you will not switch
it.
You have to switch in the
item of the disc menu.
If the disc has not record
subtitle. The subtitle can't
display.
Do not display
the subtitle
The playing DVD has no
subtitle.
If the disc has not record
subtitle. The subtitle can't
display.
You only switch in display
items of the disc menu.
Use the disc menu to switch.
Fails to accord
to D/K mode in
DVD SETUP
to carry out
playing.
The playing DVD has not
multi-lingual record content.
If the disc has not record the
selecting language in DVD
SETUP. It can
't switch to
selecting language.
Fails to switch
angle
You are trying to multi-angle
watch scene which has not
shoot from milti-angle.
Watch the record scene from
multi-angle shoot to switch in
multi-angle.
If the DVD has not record the
scent from multi-angle, you will
not switch in multi-angle.
The playing DVD has not
shoot scene which from
multi-angle.
The picture
unclear /
Distortion &
Dark.
The disc has signal which
forbid copy.
(Some may have this
signal.)
Because of the unit compatible
duplication system.
Therefore, when play the disc
which has forbid copying signal,
the image can watch when
certain display monitors appear
the horizontal stripe or oder
flaws.
The troubles in VCD playing
Trouble
Reason
Measure
PBC (play control)
menu display will
not be searched
out.
The playing VCD has
no PBC.
The VCD without PBC can not
carry out this operation.
Fails to repeat &
track and time
searching.
The playing VCD has
PBC.
The VCD with PBC can not
carry out this operation.
5
Disc Handling And Maintenance
Disc UsingDisc Using
Correct
Do not stick the label or adhere things on the disc.
Incorrect
Do not expose the disc into direct sunshine or near the hot sources.
After playing, please store it into the disc box.
To keep the disc clean, please hold the disc edge only, do not touch its
surface.
Disc CleaningDisc Cleaning
11
22
Before playing, wipe the disc with a clean cloth, from the centre hole
towards the outer edge .
Never use alcohol, thinner, cleaning fluid, static electricity prevention
liquids or any other solvent to clean discs.
Disc StoringDisc Storing
After playing, please store the disc into the disc box and keep them in room
temperature. It can help to extend the using life of the disc effectively.
38
Troubleshooting
Common Trouble
Trouble
Reason
Measure
The power
fails to put
through the
unit does not
work
The down-lead and tie-in
has disconnected.
Please check whether the power
has been connected correctly.
Fuse broke off.
Removes reason which the fuse
broke off, then chang the fuse.
For god's sake to install the right
same tating fuse.
Press 'RESET' button.
The noise and other factor
caused the Built-in MPU
fails to work normally.
No sound
The wire has discconnected.
Connect the wire correctly.
The unit enforcing the play
with repose, slow motion or
per frame to play.
Enforce the repose, slow motion
or per frame to play has no
sound.
No picture
The grip brake wire has
disconnected.
Connect the grip brak wrie, then
pull it up.
The grip brake has not
pulled up.
Connect the grip brak wrie, then
pull it up.
Icon display,
the operation
is unable to
carry on
The disc forbid operating.
The operation is unable to cany
on.
The operation is unable to cany
on.
This operation's structure
with the disc do not
compatible.
Audio and
video leap
The unit installed loose.
Fix the unit steadily.
Touch screen
can t operate
normally by
tiuching
'
Built-in MPU is unable to
normal work.
After launder the operations
normally.
Radio signal too low to store the
correct frequenly into the
storage.
The remote
control does
not work
The remote control does
not aim at its receiver
window.
The battery of remote
control die down.
The remote control aimed its
receive window.
Please use new battery instead.
Fail to reset
tune in radio
mode.
6
Playable Disc
This unit can play DVD, S-VCD, VCD, CD, MP3, MP4 etc. format discs.
Disc
types
Disc
symbols
Recorded
Contents
Disc Sizes
Playing time
DVD
S-VCD
VCD
CD
M
P
3
VIDEOVIDEO
Audio+Video
(Motion Picture)
12cm
About 2 hours
(single side disc)
About 4 hours
(double sides disc)
SVCD
Audio+Video
(Motion Picture)
12cm
About 45 minutes
COMPACT
DIGITAL VIDEO
Audio+Video
(Motion Picture)
12cm
About 74 minutes
COMPACT
DIGITAL AUDIO
Audio
Audio
12cm
12cm
About 74 minutes
About 600 minutes
NOTICE:
Some DVD, S-VCD, VCD discs playing operation may be limited by the software
designer s special regulation, please refer to the instruction manual of disc. This
unit can play recorded discs (CD-R,CD-RW) too, but it depends on the quality and
recorded situation, some kinds of discs can not play in this unit.
This player cannot playback diameter 8cm disc. To avoid damage of it, please
do not insert and play the above mentioned disc in this player.
PAY ATTENTION :
M
P
4
Audio+Video
compressed format
12cm
37
Touch screen function introduction
1
2
3
4
(Note: The product does not correct any more after leaving factory,
because of all of products were corrected in production.
When touch no effection in the center screen, but touch the
sides of screen is valid,first press
' RESET '; and press
' POWER 'all the while, then leave the ' RESET ', press ' POWER '
over 2 seconds.
TV system/Radio frequency setup
Picture 9-4
This interface setup TV system/radio frequency according to customer s
location. After setup it, press POWER on panel over 2 sec to turn off the unit
on panel over 2 sec to turn off the unit once, it will memory long this setup.
,
AUDIO VIDEO OSD SYS
QUIT
TV
PAL BG
DK
NTSC I
M
SECAM N
L
L
RADIO
EUR.
USA.
AUS.
RUS.
MD,EAST
7
Front Panel s Diagram
7. Clock display button
1. Power on/off & mute button
1 2
3
4
5
6
8
7
9
10
1112
13
14
15
6. Disc slot window
5. Disc play/pause button
14. LCD
8. Disc eject button
10. USB port
3. Radio /searching up/DVD/next track/ fast-forward
4. Radio/searching down/ DVD/last track/fast-backward
15. Volume +/- button
9. Remote control receiver
2. RESET button
13. TFT off
11. Radio/DVD/video/USB switch
12.PAL/NTSC switch
R
IR
36
Touch screen character grounding setup
AUDIO VIDEO OSD SYS
QUIT
BACK.G
TRANS
BACK.R
00
07
22
BACK.B
00
2
1
Picture 9-3
Touch screen function introduction
07
1 Character grounding setup
Touch TRANS to adjust the dark/light of character grounding.
2 RGB setup
Setup BACK.R/BACK.G/BACK.B to adjust the grounding of monitor, from
default blue to adjust to red/yellow etc.
If want to memory you setting color, after selecting you want it, Touch
QUIT for exit, turn off ' POWER ' and turn on it, you selected color will
memory in the unit for long time.
Touch screen correcting setup
To set up this button when touch screen working has warp,in order to set up
accurately, you can choose pointed tools (but pay attention to not damage
the screen surface) to operate. Touch
' ' the center point in picture 9-3 to
appear ' + ' four times in turn(see next picture).According to the sequence of
picture,each time appear' + 'to click the crosspoint of ' + ',until click the fourth
to finish correction.
(Note: While correct the touch screen, must point at the ' + ' center point and
cant't touch other position or it will no effect or incline.)
8
11. Clock display button
10. Volume up
5. Radio/stereo&DVD/stop
button/*Return
9. OSD/CLEAR button/*GPS
2. Random button
3. Repeat button
4. Set up button/*Location
8. Radio/searching down/last track
& fast-backward/*Zoom out
7. Direction button / / /
6. Radio/DVD/video/USB switch
13. Language menu
14. Menu button
15. Radio/searching up/next track &
& fast-forward/*Zoom in
16. Confirm button
17. Band & Play/pause button
18. Title/zoom button
19. Radio/AMS & DVD/Searching
/Bookmarking/Program
20. PAL/NTSC switch
21. Numeric button
1-9, 0/10,10+
22. Power ON/OFF & mute button
1. Disc eject button 12. Volume down
Remote Control s Diagram
+
SETUPSETUP
STOP
_
77
88
9 9
0/100/10
10+10+
11
22
33
44
55
66
1
2
3
4
5
6
7
8
9
10
11
12
13
14
15
16
17
18
19
20
21
22
(Note:The function with only is valid in GPS mode.)
**
35
Picture setup
1 Personel picture effect setup.
Touch one of 1 - 5 on screen and adjust SATURATION/HUE/CONTRAST/
BRIGHT then the setup parameter will automatically to one of 1 - 5 which
selected.
Touch screen function introduction
AUDIO VIDEO OSD SYS
1 2 3 4 5
HUE
BRIGHT
CONTRAST
30
17
20
SA TURA TION
30
QUIT
1
2
3
4
5
Picture 9-2
2 SATURATION setup
Touch SATURATION 20 to adjust the saturation of picture color.
3 HUE setup
Touch HUE 30 to adjust the deep/light of picture color.
4 CONTRAST setup
Touch CONTRAST 30 to adjust the picture contrast.
5 BRIGHT setup
Touch BRIGHT 30 to adjust the picture bright.
6 Treble adjust setup
Touch TRE to decrease treble loudness, touch TRE to increase treble
loudness.
7 Bass adjust setup
Touch BASS to decrease bass loudness, touch BASS to increase
bass loudness.
9
Function Instructions
Press this button on panel/remote control to turn on the player.In turn on mode,
Press this button to activate the selecting mode of mute on/off.Press it for over
2 seconds to turn off the unit.
Power on/off & mute button( )
Volume control button(VOL+/-)
Press VOL+/- on panel or press it on remote control anytime to increase or
decrease the volume.
''
Reset button(RESET)
Press this button on panel to reset all the setting to default.
In radio mode, press this button time and again to select needed band [FM1,FM2,
FM3,AM1,AM2,AM3].
In playing disc mode, means disc playing or pause function.
Band switch & play/pause
Clock display button(CLK)
1. Press display the time on screen.
2. Press it press
VOL
'CLK' button will
over 2 sec to enter the time adjust mode, the minute flashes,
'+/-' to adjust it, then press 'CLK' again, the hour flashes, press VOL'+/-'
to adjust it, after adjusting press it over 2 sec. the time will stop flashing.
Notice: The time will not disappear automatically. If you wouldn't like to display
the time, press 'CLK' once again.
Stereo and L/R channel button(S.L.R)
1. In FM band, press this button to switch Mono, Stereo output.
2. In disc playing mode, if the contents of disc have channel switch function,
press it to switch Stereo/Left/Right channel output.
TFT OFF button
Press 'TFT OFF' button on panel to close or open the TFT monitor.
34
digit add 1 (If select track 35, first touch 10+ three times, then touch
5 ). ( VCD/DVD only)
13 QUIT For page quit button, touch it to quit the current page to return to
last page.
Touch screen function introduction
E Multi-functional setup interface operation
After entering this interface AUDIO for audio setup interface see picture
9-1 VIDEO for picture setup interface see picture 9-2 OSD for screen
display accord interface ( see picture 9-3 SYS for country system select
setup interface see picture 9-4 .
AUDIO VIDEO OSD SYS
EQ 1 2 3 4 5
LOUD
BASS
TRE,
--
--
OFF
QUIT
Picture 9-1
1
2
3
4
5
6
7
Audio setup
1 Front/rear speaker setup touch to setup the volume of front speaker,
touch to setup the volume of rear speaker.
2 Left/right channel setup, touch to setup the volume of left speaker,
touch to setup the volume of right speaker.
3 Interface quit button, touch QUIT button to return the last page.
4 Personal EQ storage setup
Touch any one of 1 - 5 on screen. Then adjust BAS/TRE/LOUD the
setup parameter will store to one of 1 - 5 which selected.
5 Loud setup
Touch LOUD to close LOUD, the monitor show OFF
Touch LOUD to open LOUD, the monitor show ON
1.In radio mode, press it change to disc playing mode.If no disc but with USB
in the unit, it will change to USB mode automatically.
2. In disc playing mode, press this button to change to USB mode.If no USB in
the unit, It will change to outer video AV/AUX input mode automatically.
3. In USB mode, press this button to change to outer video AV/AUX input mode.
Press it again to resume the radio mode.
Radio DVD/video/USB switch(MODE)
press ' MODE ' button to switch as following:
Radio DVD USB AV
In disc playing mode, press it on remote control to adjust channel output as below.
Language menu(AUDIO)
Confirm button(ENTER)
Press this button to confirm the selected menu.
10
Function Instructions
Insert the disc into slot, CD will begin to play, and the name and number of the
track will appear too.
Disc slot window
Radio/searching up/DVD/next track/fast-forward( )
1. In radio mode, Press on panel/remote control to adjust the receiver
frequency up. Press and hold it for over 2 seconds to search up automatically.
2. In disc playing mode, Press to select the next track.
3. In disc playing mode, press button for over 2 seconds to select fast
forward, to select fast forward speed as following:
Example: fast backward X2, X4, X8 ,X16 playing.
f unction to select fast backward speed as following:
Example: fast backward X2, X4, X8 ,X16 playing.
1. In radio mode, Press on panel/remote control to adjust the receiver
frequency down. Press and hold it for over 2 seconds to search down
automatically.
Radio/searching down/DVD/last track/fast-backward( )
2. In disc playing mode, Press to select the last track.
3. In disc playing mode, press button over 2 seconds to select fast-backward
Disc eject button ( )
Press it to eject a disc, and change to radio mode automatically. After ejecting
the disc, it will enter automatically if not take it out in 10 seconds, but not
playing.
1. In radio made,press PRG/AMS on remote control over 3 sec, the unit will
select the strongest local 6 stations automatically to store the NO.1-6 stations in
order. FM includes FM1, FM2, FM3, each can store 6 stations, at most 18
stations. AM includes AM1, A 2, AM3, each can store 6 stations, at most 18
stations.
Auto-memory & scan storage button(AMS)
LCD
Display all selected functions.
USB function selection
Insert USB to USB port of this player, it will automatically playback the
M
33
1 Touch this button to choose track up, press it over 2 sec means fast-
backward function.
2 Touch this button means disc pause/play function.
3 Touch this button to choose track down, press it over 2 sec means
fast-forward function.
4 Repeat button, Touch this button to repeat single track playback or full
disc playback mode.
5 Random button, Touch this button to choose random function.
6 A-B Repeat playback button, fix point repeat (A-B) allow to playback
repeatly between any 2 points, In playback process, In start point (A) of
playback, when the point A has setup, then setup the end point (B) of
needed playback. When the point B has setup, then touch A-B button, it
will playback repeatly between A and B. If want to quit this function, then
touch A-B button once again.
7 MENU To setup the open and close of menu.
8 1/2 In this interface, press this button to enter the next page interface.
see picture 6
9 Source Touch this button to enter the main interface mode of unit to
choose other mode.(see picture 3
10 Setup Touch this button to enter the function setup interface.(see
picture9-1/2/3/4
QUIT
+10
1 2
3
4
5
6
7
8 9
0
Picture 6
13
12
11
11 For menu direction select, menu confirm button.
12 The digital button is used to select track, if certain part or track has 2
digits, first touch 10+ ; then touch the first digit (If select track 15, first
touch 10+ button once, then touch 5 ). Touch 10+ once, the second
Touch screen function introduction
Left Right Mix Stereo
Warning! If no operations are executed within 10 seconds after the PBC MENU
is displayed, the unit will continue to play from the first track.
1. Press the MENU button to setup PBC.
2. Press the numeric buttons to enter the segment of the track you want to play.
While PBC shut off, you can press numeric button on remote control to select
track. While PBC turn on, press numeric button on remote control can not
select track.
MENU SETUP
When playing this type of discs:
11
Function Instructions
Numeric button
In radio mode
1. Press and hold any one button 1-6 on remote control for over 2 seconds to
store the radio stations to the memory you are listening.
2. In disc playing mode, press and hold 7RPT button over 2 seconds means
Single song repeat/Full disc repeat/ repeat OFF.
3. In disc playing mode, press and hold 8RDM button over 2 seconds means
Random playback.
Press it again to shut off this function.
4. In DVD or VCD mode, first press STOP on remote control, then press and
hold 9P/N over 2 seconds interchange between PAL/NTSC systems.
2. From 1-6, press any one button to call out the memory.
In disc playing mode
1. Numeric buttons on remote control are used to select the tracks. If certain
first digit, and press the second
digit, then press ENTER button 15 ,you can press
1 once then press 5 and press ENTER button).
segment or track has two digits, press the
(eg: select track
VCD/SVCD PBC MENU
Some VCD and S-VCD discs(especially Karaoke discs) have some menus.
They are used to select the contents you want to enjoy. This type of menu can
also be called PBC .
contents of USB.
1.During USB playback mode, press button for selection of next track,
press button for selection of last track. Press 2RPT on panel or
press 7RPT on remote control over 2 seconds to select the content of
USB for repeat playback function. Press 3RDM on panel or press
8RDM on remote control over 2 seconds to select the content of USB
for random playback function. Press direction button / / / on remote
control to select you liked tracks for playback.
2.If desire changing to other playback mode, you can press MODE button
to switch.
32
Setup
Source
C. AUX mode
1 Source Touch this button to enter the main interface of unit to choose
other mode. see picture 3
2 Setup Touch this button to enter the function setup interface see picture
9-1/2/3/4
Picture 4
1
2
Touch screen function introduction
D. The operation of disc playback interface
Setup
Source
A-B
MENU
1
2
Picture 5
1 2 3 4 5 6 7 8
9
10
1 Touch this button to enter the radio mode. (See picture 1)
2 Touch this button to enter the TV mode. This unit no TV function
now).
3 This is SD card mode, when insert SD card on panel. This unit no
SD card function now).
4 Touch this button to enter the outer AUX input mode. (See picture 4)
5 Touch this button to enter the bluetooth mode.(This unit no bluetooth
function now).
6 Touch this button to enter the disc playback mode. (See picture 5)
7 Touch this button to enter the GPS mode.(While no GPS function,
so no this operation.)
8 Touch this button to enter the USB playback mode.
9 The main interface quit button, touch this button to quit the original
operation mode. For example: From disc playback mode to enter the main
interface, to quit means former disc playback mode.
QUIT
CARD
USB
RADIO
TV
AUX
DVD
PLAYER
NAV
Bluetooth
12
Function Instructions
RADIO/STEREO & DVD/STOP BUTTON
1. In disc playing mode, press this button on remote control to memory stop mode.
Press BAND/ button again to continue playback.
2. Continuously press STOP button twice to stop completely. press
BAND/ button to play the disc newly.
3. In radio mode, press this button means sound channels switch function.
1. In DVD disc playing mode, Press this button on remote control to activate
selecting title function.
TITLE/ZOOM BUTTON
2. Press this button on remote control over 2 seconds to activate the picture
enlarge function. Press once to enlarge one times of the original, twice to
enlarge for 2 times; and three times to enlarge for 3 times, press it again
to return Normal.
Radio AMS & DVD Searching/Bookmarking/Program(PRG/AMS)
1. In radio mode, press this button on remote control to use auto-memory and
scan storage function.
2. In disc playing mode, press this button for search setup playback, press it
over 2 seconds for program setup playback function. (Details will be
described in program playback).
NOTE: If has horizontal line twinkling under the screen while reverse
your car, the reason that camera video system is not same as
this unit, then press 9 P/N on remote control in order to
make the same as system between camera video and this unit.
In this way, the picture will not appear horizontal line twinkling.
All of the outer input video system must be same as this unit s,
then switch MODE button, it will not has horizontal line
twinkling.
If need to use this correct system for long time, press POWER
to turn off the unit, to turn on it again, the correct system will
memory in the unit for long time.
,
OSD/CLEAR
This information only can be watching but can t be adjusted.
Note:
1. In disc playing mode, Press OSD on remote control over 2 seconds, the
OSD will display the current playing disc message eg. Disc type, disc reading
time, title, chapter, audio, subtitle, angle,bit rate, track, ect.These display
message depends on disc type, version format and authoring of disc. (This
function don t support the still picture disc, such as CD/MP3 disc, press this
button over 2 seconds OSD no valid). If want to quit OSD, then press it over
2 seconds.
'
31
10 Touch this button to eject disc when a disc in the tray.
11 BAND Touch this button to choose FM1 FM2 FM3 AM1 AM2 AM3.
12 Last page / next page interface choose button, Touch this button to
enter the next page of radio. (See picture 4)
13 Band/LO/DX show column.
14 The disc show column, it will show the disc symbol when a disc in the tray.
FM1 DX
Setup
Source
1 8 7 . 5 0 MHz
22
BAND
1 2
3
4
5
6
Picture 2
14
15 Touch any one of 1 - 6 button over 2 sec to store the listening station to
this button memory. Touch any one of preset stations 1 - 6 to call out the
stations which preset to this memory.
B. The main interface operation
Touch screen function introduction
Picture 3
DVD
RADIO
PLAYER
CARD
NAV
Bluetooth
TV
AUX
USB
QUIT
1
5
2
6
3
7
4
8 9
13
Basic Operations
Basic playback
In disc playing mode, press on panel or remote control to eject the
disc, if doesn't take out the disc, and press it to start playback. If no take it
out within 10 seconds, it will enter the units automatically, but no reading
disc, display radio mode interface and disc icon. If want to continue
playback, press MODE to switch to disc playing mode and playback it
repeatly.
Pausing Playback
1. P to pause playback (still mode ). ress BAND/ on remote control
2. Press to resume normal playback. BAND/ on remote control
Stopping Playback (show the Player logo screen ) and Resuming
Playback after Stopping
1. Press STOP to stop playback and show the logo playback is stopped.
2. Press to resume playback
from the location where playback is stopped (DVD, VCD 1.1, VCD 2.0/SVCD/
CVD and audio CD).
BAND/ on remote control
3. Press STOP twice to stop playing, then press
to resume playback from the beginning of the disc.
BAND/ on remote control
Fast Forward/Fast Backward
In normal disc playing mode, press or on panel or remote control
for fast forward / fast backward, each press it over 2 seconds once, the
different speed will be selected as X2, X4, X8, X16 for fast forward /fast
backward, the most speed is X16 . In X16 fast forward speed mode, press
over 2 seconds to resume normal playback. In X16 fast backward
speed mode, press over 2 seconds to resume normal playback.
Menu Navigation (DVD/VCD)
1. Press TITLE to invoke Title Menu (DVD/VCD only, dependent on authoring of
disc).
2. Press direction buttons to highlight selected Title Menu entry.
3. Press ENTER or BAND/ on remote control to select the highlighted entry.
If the highlighted entry indicates a title,t hat title will play from Chapter 1.
4. Press MENU to invoke the menu screen included on many DVDs (DVD only).
5. Press direction buttons to highlight a selected menu entry. / / /
It must open PBC in VCD format, or it will return to title menu.
30
When turn on the unit first time, the monitor will enter the radio default interface.
The display mode as picture 1:
FM1 DX
Setup
Source
1 8 7 . 5 0 MHz
22
AMS
LO
DX
BAND
Picture 1
1
3
4
2
5 6 7 8 9
10
11 12
13
1 Source Touch this button to enter the main interface mode to choose
other mode. (See picture 3)
2 Setup Touch this button to enter function setup interface. see picture
9-1/2/3/4
3 The show column of radio position and frequency.
4 The show column of volumn adjustment.
5 Touch this button to search stations up, press it over 2 seconds to
search stations fast upward.
6 AMS Touch this button to search stations automatically, and played 5
seconds in each station, touch it over 2 sec to search stations
automatically, and stored to NO.1-6 in order. FM stored in FM1:1-6,
FM2:1-6 , FM3:1-6, at most 18 stations, AM stored in AM1:1-6, AM2:1-6 ,
AM3:1-6, at most 18 stations.
7 Touch this button to search stations down, press it over 2 seconds to
search stations fast downward.
8 Touch this button to choose LO/DX mode, the show column will
display opeartion indication: LO or DX.
9 Touch this button to choose Radio/Stereo/Mono mode.
Picture 1 introduction:
LO
DX
14
Touch screen function introduction
A. The introduction of radio s touch interface
14
Basic Operations
Menu Navigation (PBC)
1. Press MENU to enable/disable PBC functionality with VCD 2.0/SVCD/CVD discs.
PBC must be enable for menu navigation.
2. Press a number on the number pad to select a track to play (VCD 2.0/SVCD/CVD
only).
Note:
While VCD in PBC shut off, you can press numeric button on remote control to
select track. In PBC turn on, press numeric button can t select track directly.
You should press PRG/AMS button to select track in searching.
'
Skipping to the Next/Previous Chapter/Track
1. Press to skip forward to the beginning of the next chapter (DVD) or track
(VCD/SVCD/CVD, audio CD).
2. Press to skip backward to the beginning of the previous chapter or track.
Note:
Playback resumes to normal speed after skipping to the beginning of a chapter.
Advanced Playback
1. Search playback
A. In disc playing mode, press PRG/AMS on remote control once, to pop
up the search setup item: title, chapter, track, time, full disc time, etc.
For selecting setup search playback, the setup column display depends
on disc format.
B. Enter the search setup column, press / direction button on remote
control to move the yellow cursor, until to desired option, press 0 - 9
numeric button on remote control to set the desired title, chapter, track,
time or full disc time, etc. then press Enter enter the setting search
position for playback.
Note: press PRG/AMS once, to pop up search setup column, if no
operation in 10 seconds, the setup column will disappear
automatically.
2. Program playback
A. In DVD/VCD playing mode, press PRG/AMS on remote control over 2
seconds to enter the program playback list, press / direction button
on remote control to move the yellow cursor, and select title, chapter or
6. Press ENTER or BAND/ on remote control to select the highlighted entry.
If the highlighted entry indicates a c hapter or title, the disc will play from the
selected spot.
00 00 23
Track01
Track02
Track03
Track04
Track05
Track06
Track07
07/16
/CD01/Track06.MP3
Filter
Repeat :Off
Mode :Normal
Music Playing
29
MP3 Functions
MP3 adopts to a standard which is the newest compressed technique of video digital
playing, one disc can store more than 600 types of music, or more than 160 songs, and
have the same quality as CD.
Use the digital button to select the song playing directly.
1. According to the basic operating process, insert the disc correctly, the player will
start to search the disc information, and then show the message on the screen.
DISC PLAYBACK
1. The MP3 Menu is automatically opened and a list of tracks displayed when an MP3
disc is inserted into the player.
2. Within 10 tracks can be selected to press numeric button directly.
3. Selecting track is two digit or three digit.
Eg: selecting the 35th track, press 3 button, and press 5 ,then press
ENTER button it will playback the 35th track automatically. If selecting
135th track, press 1 button, and press 3 button, then press 5 , and
press ENTER again.
SELECT TRACK
The player plays the first track automatically, the elapsed time within the
track is displayed on the right side of the top line, when the track is finished,
the second track will begin playing and the track number on the top line will
be updated. Press STOP to stop playback of the current track.
Means all the tracks of disc
Means the playing track
Means current folder
Means the playing time
Means the current playing track
Selecting a Track to Play
2. Press the RIGHT direction button when the highlighted track is in the column on
the far right, and up to five more tracks in the current directory will be displayed.
3. Press the LEFT direction button when the highlighted track is in the column to the
far left, and the previous five tracks will be displayed.
4. Press ENTER on a track number, and that track will begin to play.
5. Enter a track number with the number keys to play a track and press SELECT/
ENTER. The digits will a ppear in the message area as the keys are pressed.
In this case, the track di splay doesn t change. After pressing SELECT/ENTER, the
track display changes if the selected track is not in the current display.
1. Use the / / / direction buttons to move to different track numbers.
15
Basic Operations
3. CD/MP3 Program playback
Step1 select files add to program playback list.
A. In CD/MP3 menu, press direction button on remote control to select
yellow cursor, then move to right.
B. Next to press / direction button, and select Edit mode , then
press Enter button (now Edit mode was selected).
C. Next to press direction button, select the files which need add to
program list, press Enter button (the selected files have marks.)
D. After selecting files which need to add to program list, press
direction button, then press direction button select add to program,
press Enter on remote control (Now the selected files of C will add to
program list).
B. After programed chapters/tracks for need to playback, press
direction button to move the yellow cursor to select Play , press
Enter to playback the programed chapters/tracks in program list.
C. In program mode, move the yellow cursor to Clear , press Enter
to clear the last chapter/track in the program list, then move the yellow
cursor to Clear all , press Enter to clear all of chapters/tracks in the
program list, next to press PRG/AMS over 2 seconds to continue
playback the current disc.
Program
Track 1
Track 2
Track 3
Track 4
Track 5
Track 6
1 2
3 4
5 6
7 8
9 10
11 12
13 14
15 16
Clear
Clear All
Play
The current
playing disc
track list
Program list
track for program in the left list, then press Enter to program into the
right program list, this list was most programed 16 chapters/tracks as
bellow:
28
Basic Operations
Language
Video
Audio
Rating
Misc
Divx Video Demand
Your registration code is:
D7YYMU91
(http://www.divx.com/vod)
OK
3. Press direction button, move cursor to Divx Registration option,
press Enter to pop up the following window, select OK option.
4. Press direction button, move cursor to Screen saver option,
press Enter to select On/Off option.
On = Turn on screen saver
Off = Turn off screen saver
16
Basic Operations
Step2 view the program list.
00 00 23
Track01
Track02
Track03
Track04
Track05
Track06
Track07
07/16
/CD01/Track06.MP3
Filter
Repeat :Off
Mode :Normal
Music Playing
E. Next to D press direction button to select program view (Now the
selected files of C will display on the left).
Step3 play the tracks of program list.
F. Next to E press direction button, the cursor move to program mode,
press Enter button (Now quit program mode).
G. Next to press direction button, select desired playback track in
program list, press Enter to start program playback.
Step4 add the tracks to program list.
H. If add tracks to program list, repeat A-E operation to add the tracks of
program list.
Step5 clear the tracks of program list.
I. First press STOP on remote control twice to stop the current playback
fully.
J. Next to G or H press direction button, then press / direction button
to select Edit mode newly.
K. Now select the tracks of program list randomly, the selected tracks have
marks.
L. Then press direction button to move yellow cursor, select Clear
program playback to press Enter button, now the selected tracks of
K will be cleared from program list.
4. CD-ROM basic operation
A. CD-ROM disc is same as the CD/MP3disc operation.
B. In CD-ROM disc playing mode, press direction button to move
yellow cursor, select filter to view audio, picture, video mode, the open
mode have marks, these 3 options factory default is open mode.
C. Next to press direction button to return the left, press
direction button to select picture folder, and move cursor to select
picture files, then press Enter have picture output.
27
Basic Operations
Press / direction button to select : 1 Kid Safe/2 G/3 PG/4 PG-13
/5 PG-R/6 R/7 NC-17/8 Adult. Then press Enter to cycle through
the available option.
Kid Safe = Only title a parental control setting of 1 are allowed to play
G = Only title a parental control setting of 2 or less are allowed to play
PG = Only title a parental control setting of 3 or less are allowed to play
PG-13 = Only title a parental control setting of 4 or less are allowed to play
PG-R = Only title a parental control setting of 5 or less are allowed to play
R = Only title a parental control setting of 6 or less are allowed to play
NC-17 = Only title a parental control setting of 7 or less are allowed to play
Adult = Allow any title to play (factory default).
Notes:
1. Parental Control functions only if the DVD title has it encoded in its
program. Parental Control does not work for VCD/SVCD/CVD or CD Audio.
2. The Rating can change only while unlock the password.
3. Set password setting:
Press / direction button, move yellow cursor to Set password ,
press Enter to pop up the Enter password window, enter the
back-door password (Back-door password:8888) then set new password,
and open parental control options.
Misc settings
1. In setup interface mode, press / direction button, move yellow
cursor to Misc option, press Enter to appear Misc as bellow:
2. Press direction button, move cursor to Use Default Settings option,
press Enter to pop up window Use Default Settings , there are two
selections: Yes/No.
No = Return to use Default Settings.
Yes = Use Default Settings.
Divx Registration
Language
Video
Audio
Rating
Misc
Use Default Settings
Screen saver :On
17
Basic Operations
D. Next to press STOP button to return picture files list, press /
direction button to view picture files, then the picture from picture files will
display in the right JPEG preview window.
E. At the same time the audio and picture playback mode, press Title/Zoom
on remote control to preview 9 menu, then press / / / direction
button to select the desired picture, then press Enter to open it.
F.In open picture mode,press direction button to rotate picture
clockwise for 90 degrees,press it again for 180 degrees,then press it for
270 degrees,next press it the picture no rotate to back normal mode.
press direction button to rotate counter clockwise for 90 degrees,
press it again for 180 degrees,then press it for 270 degrees,next press it
the picture no rotate to back normal mode.
Press / direction button to rotate picture for 180 degrees,press it
again the picture no rotate to back normal mode.
Filter
Repeat :Off
Mode :Normal
Music Playing
00 00 23
Track01
Track02
Track03
Track04
Track05
Track06
Track07
Track08
07/16
/Track06.CDA
Contents Ripping
SD card & USB Ripping
To insert CD format disc playback while SD card & USB in the unit as below
(This operation is valid only CD format disc.)
1.press direction button to move the cursor to right side,then press
/ direction button to move the cursor to Ripping ,press Enter
on remote control to confirm.
(This unit no SD card function now.)
*
26
Basic Operations
Language
Video
Audio
Rating
Misc
Digital Output :PCM
Smart Sound
Off
Classical
Rock
Jazz
Pop
Press / direction button to select : Off/Classical/Rock/Jazz/Pop
option. Press Enter to cycle through the available option.
Language
Video
Audio
Rating
Misc
Parental control :8. Adult
Set Password
Rating settings
1. In setup interface mode, press / direction button to move yellow
cursor to Rating option, press Enter to appear Ratings as bellow:
Language
Video
Audio
Rating
Misc
Set Password
Parental control
1 Kid Safe
2G
3PG
4 PG-13
5 PG-R
6R
7 NC-17
8 Adult
2. Press direction button, move cursor to Parental control option,
press Enter to appear 8 kinds of Parental control for selection as bellow:
18
Basic Operations
00 00 23
Track01
Track02
Track03
Track04
Track05
Track06
Track07
Track08
07/16
/Track06.CDA
Contents Ripping
Destination
Select all
Rip quality:High
Available space
0MB
Size of selected
0MB
2.Next to press direction button to move the cursor to Destination
then press Enter on remote control to appear 2 kinds of destination for
selecting.
00 00 23
Track01
Track02
Track03
Track04
Track05
Track06
Track07
Track08
07/16
/Track06.CDA
Contents Ripping
Destination
Select all
Rip quality:High
Available space
0MB
Size of selected
0MB
SD
USB
press direction button to select SD card or USB option,then
press Enter to appear mark in back of the confirmed option.
3.Next to press / direction button to select the desired files whilch
ripping to SD card or USB ,ten press Enter button (the selected
files have marks).
If will select all to press direction button to move the cursor to
Select all ,then press Enter to confirm.
If will unselect all to press direction button to move the cursor to
Unselect all ,then press Enter to confirm.
25
Basic Operations
Press / direction button to select : Standard/Bright/Soft/Dynamic
option, press Enter to cycle through the available option.
Language
Video
Audio
Rating
Misc
Digital Output :PCM
Smart Sound :Off
Audio settings
1. In setup interface mode, press / direction button to move yellow
cursor to Audio option, press Enter to appear as bellow:
2. Press direction button, move cursor to Digital Output option,
press Enter to appear 3 kinds of Digital Output for selection as bellow:
Language
Video
Audio
Rating
Misc
Digital Output
Smart Sound
Off
PCM
All
Press / direction button to select : Off/PCM /All option. Press Enter
to cycle through the available option.
3. Press direction button, move cursor to Smart Sound option,
press Enter to appear 5 kinds of Smart Sound for selection as bellow:
5.Next to press direction button to move the cursor to Ripping
start ,then press Enter to start ripping.
If want to stop ripping, press Enter directly,press direction
button to select Yes ,then press Enter to confirm.
Contents Ripping
Un select all
Rip quality:High
start
Available space
0MB
Size of selected
29MB
00 00 23
Track01
Track02
Track03
Track04
Track05
Track06
Track07
Track08
07/16
/Track06.CDA
Dont remove card
Track 0.2.CAD
Cancel
0/100
19
00 00 23
Track01
Track02
Track03
Track04
Track05
Track06
Track07
Track08
07/16
/Track06.CDA
Contents Ripping
Un select all
Rip quality:High
start
Available space
0MB
Size of selected
29MB
Dont remove card
Track 0.2.CAD
Cancel
0/100
Do want to stops
Yes
Basic Operations
4.After selecting the desired files which ripping to SD card or USB ,
press / direction button to move the cursor to Rip quality ,
press Enter to select the rip quality[Medium/High/Best/Low].
No
Basic Operations
Language
Video
Audio
Rating
Misc
Aspect Ratio : 4 : 3
View Mode
TV System
Smart Picture
Fill
Original
Auto Fit
Pan Scan
3. Press direction button, move cursor to Video mode option, press
Enter to appear 4 kinds of video mode for selection as bellow:
Press / direction button to select : Fill/Original/Auto Fit/Pan Scan
option, press Enter to cycle through the available option.
Language
Video
Audio
Rating
Misc
Aspect Ratio : 4 : 3
View Mode : Auto Fit
TV System
Smart Picture
NTSC
PAL
Auto
4. Press direction button, move cursor to TV system option, press
Enter to appear 3 kinds of TV system for selection as bellow:
Press / direction button to select : NTSC/PAL/Auto option, press
Enter to cycle through the available option.
5. Press direction button, move cursor to Smart Picture option, press
Enter to appear 4 kinds of Smart Picture for selection as bellow:
Language
Video
Audio
Rating
Misc
Aspect Ratio : 4 : 3
View Mode : Auto Fit
TV System : NTSC
Smart Picture
Standard
Bright
Soft
Dynamic
24
20
Playback setup interface operation
To enter setup interface
A. In disc playing mode, press Setup once remote control to enter setup
interface.
B. In setup interface have 5 option for selection: Language, Video, Audio,
Rating, Misc.
Language
Video
Audio
Rating
Misc
OSD language English
Subtitle English
DIVX Subtitle Unicode
Audio English
DVD menu English
Language settings
1. In setup interface mode, press / direction button on remote control
to move yellow cursor to Language option, press Enter to appear as
bellow:
2. Press direction button to move cursor to OSD Language , press
Enter to appear 9 kinds of language for selection as bellow:
English
Francais
Espanol
Italiano
Portugues
Turkce
Russian
Language
Video
Audio
Rating
Misc
OSD language
Subtitle
DIVX Subtitle
Audio
DVD menu
~
~
..
Basic Operations
Basic Operations
23
Press / direction button to select different subtitle language: English/
French/Spanish/Italian/Portuguese/Thal/Chinese/Turkish/Russian. Then
press Enter to cycle through the available option.
Notes:
1. The above language output depends on disc.
2. The factory default language preference is English.
Language
Video
Audio
Rating
Misc
Aspect Ratio 4 : 3
View Mode Auto Fit
TV System NTSC
Smart Picture Standard
Video settings
1. In setup interface mode, press / direction button to move yellow
cursor to Video option, press Enter to appear video setup as bellow:
2. Press direction button to move cursor to Aspect Ratio option,
press Enter to appear 2 kinds of mode for selection as bellow:
Language
Video
Audio
Rating
Misc
Aspect Ratio 4 : 3
View Mode 16:9
TV System
Smart Picture Standard
Press / direction button to select : 4:3 / 16:9 option, press Enter to
cycle through the available option.
Page is loading ...
-
1
-
2
-
3
-
4
-
5
-
6
-
7
-
8
-
9
-
10
-
11
-
12
-
13
-
14
-
15
-
16
-
17
-
18
-
19
-
20
-
21
Ask a question and I''ll find the answer in the document
Finding information in a document is now easier with AI
Related papers
Other documents
-
Boss Audio Systems BV9996BT Owner's manual
-
Aiwa AMD-006 User manual
-
Hyundai H-LCDVD701 User manual
-
ELECTCOM ELECTCOM DVD Player, DVD Players for TV User manual
-
ELECTCOM DVD Player, ELECTCOM DVD Players for TV User manual
-
Audiovox MMD7HRPKG Owner's manual
-
Denver MT-774 User manual
-
Foramor DVD Player,Foramor HDMI DVD Player for TV Support 1080P Full HD User manual
-
Planet Aaudio P9725B User manual
-
SoundMax SM-DVD5107 Owner's manual
