BLACK DECKER VO1700A Owner's manual

Category
Vacuum cleaners
Type
Owner's manual

This manual is also suitable for

1
UK
Ireland
Australia
New Zealand
www.blackanddecker.co.uk
2
3
2 3
4
5
6
7
1
9
8
A
4
19
6
18
17
14
15
16
16
13
11
10 12
B C
D E
5
6
20
11 10
12
13
21 7
6
4
19
10
11
F
G H
6
30 29
31
8
28
22
5
I J
K L
7
38
36
3734
34 35
8 32
33
M N
O P
8
40 41
39
RQ
9
Intended use
Your Black & Decker vacuum cleaner has been designed to
vacuum dry substances. This product is intended for household
use only.
Safety instructions
Warning! When using mains-powered appliances, basic
safety precautions, including the following, should always
be followed to reduce the risk of fire, electric shock,
personal injury and material damage.
Read all of this manual carefully before using the
appliance.
The intended use is described in this manual. The use of
any accessory or attachment or the performance of any
operation with this appliance other than those
recommended in this instruction manual may present a
risk of personal injury.
Retain this manual for future reference.
Using your appliance
Make sure that the appliance is switched off before
connecting to or disconnecting from the power supply.
Always take care when using the appliance.
Do not use the appliance outdoors.
Never pull the power supply cord to disconnect the plug
from the socket. Keep the power supply cord away from
heat, oil and sharp edges.
If the power supply cord is damaged during use,
disconnect the appliance from the power supply
immediately. Do not touch the power supply cord before
disconnecting from the power supply.
Disconnect the appliance from the power supply when not
in use, before fitting or removing parts and before
cleaning.
Safety of others
Do not allow children or any person unfamiliar with these
instructions to use the appliance.
Do not allow children or animals to come near the work
area or to touch the appliance or power supply cord. Close
supervision is necessary when the appliance is used near
children.
After use
Switch off and remove the plug from the socket before
leaving the appliance unattended and before changing,
cleaning or inspecting any parts of the appliance.
When not in use, the appliance should be stored in a dry
place. Children should not have access to stored
appliances.
Inspection and repairs
Before use, check the appliance for damaged or defective
parts. Check for breakage of parts, damage to switches
and any other conditions that may affect its operation.
Do not use the appliance if any part is damaged or
defective.
Have any damaged or defective parts repaired or replaced
by an authorised repair agent.
Before use, check the power supply cord for signs of
damage, ageing and wear.
Do not use the appliance if the power supply cord or
mains plug is damaged or defective.
If the power supply cord or mains plug is damaged or
defective it must be repaired by an authorised repair
agent in order to avoid a hazard. Do not cut the power
supply cord and do not attempt to repair it yourself.
Never attempt to remove or replace any parts other than
those specified in this manual.
Double insulation
This appliance is double insulated; therefore no
earth wire is required. Always check that the power
supply corresponds to the voltage on the rating
plate.
Additional safety instructions for Australia and New
Zealand
This appliance is not intended for use by young or infirm
persons without supervision. Children must be supervised
to ensure they do not play with the appliance.
If the supply cord is damaged, it must be replaced by the
manufacturer or an authorised Black & Decker Service
Centre in order to avoid a hazard.
Additional safety instructions for vacuum cleaners
Before use, always make sure that the filters are correctly
seated. Do not use the appliance without all filters in
place.
Do not carry the appliance at the container handle.
Do not use the appliance to pick up liquids.
Do not use the appliance to pick up any materials that
could catch fire.
Do not use the appliance near water. Do not immerse the
appliance in water.
Keep the motor draught away from your eyes and face.
Keep children and animals at a safe distance when using
this appliance.
Always work from bottom up when using the appliance on
stairs, and keep the appliance at least a stair below your
working position.
10
Always be aware of the position of the power cord and
hose while using the appliance.
Do not use the appliance without the suction head or
another suitable accessory mounted to the tube.
After use, fully rewind the power cord and store the
appliance in a tidy manner.
Keep your hair, clothing and gloves away from moving parts.
Do not use damaged accessories.
Use only Black & Decker accessories.
Features
This appliance includes some or all of the following features
(fig. A).
1. On/off switch
2. Cord rewind button
3. Handle
4. Hose
5. Airflow control switch
6. Tube
7. Suction head
8. Container
9. Wheels
In addition, this appliance is supplied with some or all of the
following accessories (fig. B):
10. Crevice tool
11. Brush tool
12. Accessory holder
13. Parquet floor head (VO1710)
The parquet floor head is not included with all models. This
accessory is available from your Black & Decker dealer /
service centre.
Assembly
Connecting the hose (fig. C)
Insert the hose connector (15) into the inlet (14) of the
appliance.
Push the hose until the release buttons (16) click into
place.
To disconnect the hose, press the release buttons and pull
out the hose.
VO1700/VO1700A - Assembling the tube (fig. D)
Push the lower tube (17) firmly into the upper tube (18),
until they fit tightly.
Connecting the tube (fig. E)
Push the hose nozzle (19) into the tube (6).
To remove the tube, pull the hose out of the tube.
Mounting the suction head (fig. F)
The suction head (7) allows for vacuuming on carpet and hard
surfaces (e.g. laminate and tiles).
Push the tube (6) into the head (7).
To remove the head, pull the tube out of the head.
VO1710 - Mounting the parquet floor head (fig. F)
The parquet floor head (13) allows for vacuuming on wooden
and polished surfaces.
Push the tube (6) into the head (13).
To remove the head, pull the tube out of the head.
Mounting accessories (fig. F & G)
The crevice tool (10) allows for vacuuming in narrow and hard-to-
reach places. The brush tool (11) allows for vacuuming on
furniture, blinds, curtains, windows and stairs. The accessories
can be mounted on both the hose (4) and the tube (6). When not in
use, the accessories can be stored in the accessory holder (12).
Remove the accessory from the holder (fig. G).
Push the accessory onto the hose nozzle (19) or the tube
(6) (fig. F).
To remove an accessory, pull the accessory from the hose
nozzle or the tube.
Use
Unwinding and rewinding the power cord (fig. A)
The cord rewind button (2) can be operated by hand or foot.
Pull a sufficient length of cord from the back of the
appliance.
After use, press the cord rewind button to retract the cord
into the unit. Manually guide the cord to ensure it does
not swing back. Ensure the plug is correctly located.
VO1710 - Adjusting the tube length (fig. H)
The extension tube (6) can be adjusted as follows:
Push the knob (20) and slide the tube to the desired
length.
Release the knob.
Adjusting the suction head (fig. F)
For vacuuming on carpets, switch the brush actuator (21)
into the up position.
For vacuuming on laminates, tiles, etc., switch the brush
actuator into the down position.
Switching on and off (fig. A)
The on/off switch (1) can be operated by hand or foot.
To switch the appliance on, press the on/off switch (1).
To switch the appliance off, press the on/off switch
again.
11
Adjusting the airflow (fig. I)
Move the airflow control switch (5) to adjust the airflow as
desired.
Vacuuming
When operating the appliance, make sure that the hose is
not trapped, twisted or blocked.
In case of overheating, a cut-out will operate and the
appliance will automatically stop.
If the appliance stops operating, unplug the appliance and
allow it to cool for 2-3 hours before continuing.
Hints for optimum use
When vacuuming stairs, always start at the bottom and
work your way up. Position the appliance on the floor and
do the stairs until halfway. Then carry the appliance to a
stable position which is at least one stair below your
working position, and do the top half of the stairs.
Carrying the appliance (fig. A)
During use the appliance can be carried using the handle (3).
Temporarily parking the suction head (fig. J)
Use the park position (22) for a temporary parking of the
suction head.
Storing the appliance (fig. K)
Warning! When storing the appliance, switch the appliance
off and unplug it.
Make sure that the cord is fully rewound.
Place the appliance in an upright position.
Park the tube in the park position (28).
Store the appliance in a dry location.
Maintenance
Your Black & Decker appliance has been designed to operate
over a long period of time with a minimum of maintenance.
Continuous satisfactory operation depends upon proper
appliance care and regular cleaning.
Warning! Before performing any maintenance or cleaning on
the appliance, unplug the appliance.
Regularly clean the ventilation slots in your appliance
using a soft brush or dry cloth.
Regularly clean the motor housing using a damp cloth. Do
not use any abrasive or solvent-based cleaner.
Emptying the container (fig. L & M)
The container (8) must be emptied when the maximum mark is
reached.
Remove the hose.
Press the release button (30).
Lift the lid (31) until it locks into position (fig. L).
Hold the container at the handle (29). Take the container
(8) off the appliance.
Hold the container over a waste bin.
Press the release button (32) to open the container (fig.
M). Empty the container as necessary.
Close the base (33) by moving it upward until the lock
locates in the latch.
Re-insert the container into the appliance.
Close the lid until it locks into place.
Cleaning
Warning! Before cleaning and maintenance, switch the
appliance off and unplug it.
From time to time wipe the appliance with a damp cloth.
Do not use any abrasive or solvent-based cleaner. Do not
immerse the appliance in water.
Cleaning the container filter (fig. L - P)
The container filter prevents dust and dirt from entering the
motor housing. The filter is re-usable. To maintain efficient
suction performance, the filter should be cleaned every week,
or whenever suction performance is noticeably reduced.
Remove the container (8) from the appliance (fig. L).
Empty the container (fig. M).
Depending on the model, proceed as describe below to
clean the filter.
After replacing the filter, close the container.
Re-insert the container into the appliance.
VO1700/VO1700A (fig. N & P)
Remove the cartridge (34) by turning counterclockwise.
Pull the filter (35) out of the container.
Shake off excess dust by tapping the filter into a dustbin.
Depending on its condition, rinse the outside of the filter
with water. Allow the filter to dry for 24 hours before re-
inserting it.
Take out the filter (36) located right below the grid and
brush off any loose dust before re-inserting it.
Replace the container filter.
Re-fit the cartridge.
VO1710 (fig. O & P)
Remove the cartridge (34) by turning counterclockwise.
Loosen the filter (37) and remove it from the container.
12
Shake off excess dust by tapping the filter into a dustbin.
Warning! Do not brush or use compressed air to clean the
filter.
Depending on its condition, rinse the outside of the filter
with water. Allow the filter to dry for 24 hours before re-
inserting it.
Warning! Do not wash the inside of the filter.
Take out the filter set (38) located right below the grid
and brush off any loose dust before re-inserting it.
Replace the container filter and tighten it.
Re-fit the cartridge.
Cleaning the motor filter (fig. L & Q)
The motor filter prevents particles and larger objects from
entering the motor housing when the container is removed.
The filter is re-usable and should be cleaned regularly.
Open the lid (31) (fig. L).
Take the filter (39) out (fig. Q).
Brush any loose dust off the filter.
Replace the filter.
Close the lid.
Replacing the filters (fig. L - R)
The container filter should be replaced every 6 to 9 months
and whenever worn or damaged. When replacing the
container filter, the motor filter and the outlet filters have to
be replaced as well. Replacement filter sets are available from
your Black & Decker dealer.
Replacing the container filter (fig. L - P)
Proceed as described above to replace the filters.
Replacing the motor filter (fig. L & Q)
Proceed as described above to replace the filter.
VO1700A - Replacing the outlet filter (fig. R)
Open the cover (40).
Remove the old filter (41).
Insert the new filter as shown.
Close the cover.
VO1700/VO1710 - Replacing the HEPA filter (fig. R)
The HEPA filter reduces the amount of dust exiting the motor
housing to a minimum.
Proceed as described above to replace the filter.
Mains plug replacement (U.K. & Ireland only)
If a new mains plug needs to be fitted:
Safely dispose of the old plug.
Connect the brown lead to the live terminal in the new
plug.
Connect the blue lead to the neutral terminal.
Warning! No connection is to be made to the earth terminal.
Follow the fitting instructions supplied with good quality
plugs. Recommended fuse: 13 A.
Protecting the environment
Separate collection. This product must not be
disposed of with normal household waste.
Should you find one day that your Black & Decker product
needs replacement, or if it is of no further use to you, do not
dispose of it with household waste. Make this product
available for separate collection.
Separate collection of used products and packaging
allows materials to be recycled and used again.
Re-use of recycled materials helps prevent
environmental pollution and reduces the demand for
raw materials.
Local regulations may provide for separate collection of
electrical products from the household, at municipal waste
sites or by the retailer when you purchase a new product.
Black & Decker provides a facility for the collection and
recycling of Black & Decker products once they have reached
the end of their working life. To take advantage of this service
please return your product to any authorised repair agent who
will collect them on our behalf.
You can check the location of your nearest authorised repair
agent by contacting your local Black & Decker office at the
address indicated in this manual. Alternatively, a list of
authorised Black & Decker repair agents and full details of our
after-sales service and contacts are available on the Internet
at: www.2helpU.com
Technical data
VO1700A VO1700
VO1710
Voltage V 230 230
(Australia & New Zealand) V
AC
240
Power input W 1,700 1,700
Cable length m 4.5 5
Container size l 2.5 2.5
Weight kg 7 7
13
EC declaration of conformity
VO1700A/VO1700/VO1710
Black & Decker declares that these products conform to:
89/336/EEC, 73/23/EEC, EN 55014, EN 61000, EN 60335
Level of sound pressure,
measured according to EN 60704-1: 71 dB(A)
Kevin Hewitt
Director of Consumer Engineering
Spennymoor, County Durham DL16 6JG,
United Kingdom
1-2-2006
European Community design registration no. 351606-0001
Guarantee
Black & Decker is confident of the quality of its products and
offers an outstanding guarantee. This guarantee statement is
in addition to and in no way prejudices your statutory rights.
The guarantee is valid within the territories of the Member
States of the European Union and the European Free Trade
Area.
If a Black & Decker product becomes defective due to faulty
materials, workmanship or lack of conformity, within 24
months from the date of purchase, Black & Decker guarantees
to replace defective parts, repair products subjected to fair
wear and tear or replace such products to ensure minimum
inconvenience to the customer unless:
The product has been used for trade, professional or hire
purposes;
The product has been subjected to misuse or neglect;
The product has sustained damage through foreign
objects, substances or accidents;
Repairs have been attempted by persons other than
authorised repair agents or Black & Decker service staff.
To claim on the guarantee, you will need to submit proof of
purchase to the seller or an authorised repair agent. You can
check the location of your nearest authorised repair agent by
contacting your local Black & Decker office at the address
indicated in this manual. Alternatively, a list of authorised
Black & Decker repair agents and full details of our after-sales
service and contacts are available on the Internet at:
www.2helpU.com
Please visit our website www.blackanddecker.co.uk to
register your new Black & Decker product and to be kept up to
date on new products and special offers. Further information
on the Black & Decker brand and our range of products is
available at www.blackanddecker.co.uk
14
62
61
35
39
60
11
12
13
47
46
45
44
64
63
48
63
57
59
50
49
50
51
50
10
40
42
37
41
10
43
8
8
17
38
15
16
8
6
7
8
9
14
5
14
14
18
19
10
34
63
57
58
50
52
54
53
55
33
32
14
8
25
23
43
2
1
20
21
22
28
56
30
29
31
27
24
24
26
24
65
14
58
www.2helpU.com 13-02-06
E14649
VO1700 - VO1700A - VO1710
TYP.
1
VO1710
VO1700 / VO1700A
15
16
491084-00
02/06
Australia
Black & Decker (Australia) Pty. Ltd. Tel. 03-8720 5100
20 Fletcher Road, Mooroolbark, Fax 03-9727 5940
Victoria, 3138
New Zealand
Black & Decker Tel. 09 579 7600
81 Hugo Johnston Drive Fax 09 579 8200
Penrose, Auckland, New Zealand
United Kingdom
Black & Decker Tel. 01753 511234
210 Bath Road Fax 01753 551155
Slough, Berkshire SL1 3YD Helpline 01753 574277
  • Page 1 1
  • Page 2 2
  • Page 3 3
  • Page 4 4
  • Page 5 5
  • Page 6 6
  • Page 7 7
  • Page 8 8
  • Page 9 9
  • Page 10 10
  • Page 11 11
  • Page 12 12
  • Page 13 13
  • Page 14 14
  • Page 15 15
  • Page 16 16

BLACK DECKER VO1700A Owner's manual

Category
Vacuum cleaners
Type
Owner's manual
This manual is also suitable for

Ask a question and I''ll find the answer in the document

Finding information in a document is now easier with AI