Samsung DW-FN320T/XFA User manual

DW-FN320T

DW-FN320W

Dishwasher

user manual

imagine the possibilities

Thank you for purchasing this Samsung product.

DD81-01446E-03_EN_160125.indd 1DD81-01446E-03_EN_160125.indd 1 2016-01-25  2:32:152016-01-25  2:32:15

2_ safety information

READ AND FOLLOW THIS SAFETY INFORMATION

CAREFULLY SAVE THESE INSTRUCTIONS

Safety information

Please read this User Information carefully and keep it to refer to at a later date.

Pass it on to any subsequent owner of the appliance.

This manual contains sections of Safety Instructions, Part and Features,

Installation your dishwasher and Troubleshooting etc.

Carefully reading it before using the dishwasher will help you to use and maintain

the dishwasher properly.

The manufacturer, following a policy of constant development and up-dating of the product, may make

modiﬁcations without giving prior notice.

WARNING: When using your dishwasher, follow the below basic precautions including the following:

PROPER USE

• Do not abuse, sit on, or stand on the door or dish rack of the dishwasher.

• Do not operate your dishwasher unless all enclosure panels are properly in place. Open the door very

carefully if the dishwasher is operating. There is a risk of water squirting out.

• Do not place any heavy objects of stand on the door when it is open. The appliance could tip forward.

• When loading items to be washed:

- Locate sharp items so that they are not likely to damage the door seal;

- Load sharp knives with the handles up to reduce the risk of cut-type injuries;

• Warning : knives and other utensils with sharp points must be loaded in the basket with their points

down or placed in a horizontal position.

• Check that the detergent receptacle is empty after completion of the wash cycle.

• Do not wash plastic items unless they are marked dishwasher safe or the equivalent. For plastic items

not so marked, check the manufacturer’s recommendations.

• Use only detergent and rinse additives designed for an automatic dishwasher. Never use soap, laundry

detergent, or hand washing detergent in your dishwasher.

• Other means for disconnection from the supply must be incorporated in the ﬁxed wiring with at least 3

mm contact separation in all poles.

• Keep children away from detergent and rinse aid, keep children away from the open door of the

dishwasher, there could still be some detergent left inside.

DD81-01446E-03_EN_160125.indd 2DD81-01446E-03_EN_160125.indd 2 2016-01-25  2:32:192016-01-25  2:32:19

safety information _3

READ AND FOLLOW THIS SAFETY INFORMATION

CAREFULLY SAVE THESE INSTRUCTIONS

• Young children should be supervised to ensure that they do not play with the appliance.

• The appliance is not intended for use by young children or inﬁrm persons without supervision.

• Dishwasher detergents are strongly alkaline. They can be extremely dangerous if swallowed. Avoid

contact with skin and eyes and keep children away from the dishwasher when the door is open.

• The door should not be left in the open position since this could present a tripping hazard.

• If the supply cord is damaged, it must be replaced by the manufacturer or its service agent or a similarly

qualiﬁed person in order to avoid a hazard.

• Please dispose of packing materials properly.

• Use the dishwasher only for its intended function.

• During installation, the power supply must not be excessively or dangerously bent or ﬂattened.

• Do not tamper with controls.

• The appliance is to be connected to the water mains using new hose sets and the old hose-sets should

not be reused.

DISPOSAL

Dispose of the dishwasher packaging material correctly.

All packaging materials can be recycled.

Plastic parts are marked with the standard international abbreviations:

PE for polyethylene, e.g. sheet wrapping material

PS for polystyrene, e.g. padding material

POM polyoxymethylene, e.g. plastic clips

PP polypropylene, e.g. Salt ﬁller

ABS Acrylonitrile Butadiene Styrene, e.g. Control Panel.

WARNING: Packaging material could be dangerous for children!

For disposing of package and the appliance please go to a recycling centre. Therefore cut o the

power supply cable and make the door closing device unusable.

Cardboard packaging is manufactured from recycled paper and should be disposed in the waste

paper collection for recycling.

By ensuring this product is disposed of correctly, you will help prevent potential negative

consequences for the environment and human health, which could otherwise be caused by

inappropriate waste handling of this product.

For more detailed information about recycling of this product, please contact your local city oce and

your household waste disposal service.

DD81-01446E-03_EN_160125.indd 3DD81-01446E-03_EN_160125.indd 3 2016-01-25  2:32:192016-01-25  2:32:19

4_ safety information

Contents

PART AND FEATURES

5

5 Dishwasher features

6 Control panel

7 Displays

INSTALLING YOUR DISHWASHER

8

9 Water supply and drain

10 Connection of drain hoses

10 Position the appliance

10 Start of dishwasher

USING THE DETERGENT AND WATER

SOFTENER

11

11 Water softener

12 Loading the salt into the softener

13 Fill the rinse aid dispenser

15 Function of detergent

17 How to use the 3 in 1 option

LOADING THE DISHWASHER RACKS

18

18 Loading the upper basket

19 Loading the lower basket

19 Folding spikes of lower basket

20 Cutlery(silverware) basket

21 For washing in the dishwasher the following

cutlery/dishes

WASHING PROGRAMMES

22

22 Turning on the appliance

22 Change the program...

23 At the end of the wash cycle

23 Wash cycle table

CLEANING AND CARE

24

24 Cleaning the ﬁlters

25 Cleaning the spray arms

25 Cleaning the door

25 Caring for the dishwasher

25 Protect against freezing

26 How to keep your dishwasher in shape

TROUBLESHOOTING

27

27 Before calling for service

29 Error codes

APPENDIX

30

30 Speciﬁcations

30 Product dimension

DD81-01446E-03_EN_160125.indd 4DD81-01446E-03_EN_160125.indd 4 2016-01-25  2:32:192016-01-25  2:32:19

part and features _5

01 PART AND FEATURES

Part and features

DISHWASHER FEATURES

Front & Rear view

1

2

3

4

5

6

7

8

9

10

1 Upper Basket 4 Salt Container 7 Spray arms 10 Drain hose

2 Duct nozzle 5 Dispenser 8 Filter assembly

3 Lower Basket 6 Cup Shelf 9 hose

Accessory parts - User manual, Salt funnel, cutlery basket.

DD81-01446E-03_EN_160125.indd 5DD81-01446E-03_EN_160125.indd 5 2016-01-25  2:32:192016-01-25  2:32:19

6_ part and features

Part and features

CONTROL PANEL

1 5 6

7

4

3 2 8

1 POWER BUTTON Press this button to turn on your dishwasher: the screen lights up.

2 3 IN 1 OPTION BUTTON

To select 3 in 1 option which needs not salt and rinse aid but a 3 In1

tablet. This option can be selected on Intensive, Auto or Eco program

only.

3 DELAY START BUTTON

Press this button to set the delayed hours for washing. You can delay

the start of washing up to 24 hours. One press on this button delays

the start of washing by one hour.

4 CHILD LOCK BUTTON

This option allows you to lock the buttons on the control panel so

children cannot accidentally start the dishwasher by pressing the

buttons on the panel.

To lock and unlock the buttons on the control panel, hold down both

the 3 in 1 and Delay start buttons for three (3) seconds.

5 DISPLAY WINDOW Running indicator, delay time, error codes and etc.

6 PROGRAM BUTTON To select washing program press the button.

7 START/PAUSE BUTTON

In Power on condition, close the dishwasher door and select the cycle

and desired options. Press the Start/Pause button to begin the cycle.

When you want to pause the dishwasher while running, press the

Start/Pause button and make sure to open the door slowly and

carefully. You can reset the machine by pressing the Start/Pause

button for 3 seconds during washing. After reset, the dishwasher goes

to the initial state except salt consumption setting of water softener.

8 HALF LOAD BUTTON

To select Half load function. (With this Half load function you can only

use it when you have only about or less than 6 place setting dishware,

and you will see less water and energy consumption. It can only be

used with Intensive, Auto, Eco and Delicate.)

• When the door is open only the Power button will operate.

• You can select options (3 in 1, Delay start and/or Half load) before starting a cycle.

IMPORTANT: To get the best performance from your dishwasher, read all the operating instructions

before using it for the ﬁrst time.

DD81-01446E-03_EN_160125.indd 6DD81-01446E-03_EN_160125.indd 6 2016-01-25  2:32:202016-01-25  2:32:20

part and features _7

01 PART AND FEATURES

DISPLAYS

1

2

1 PROGRAM ICON When press the Program button, each program is selected.

2 3*8 SEGMENT Display the remaining time, error code, or delay time.

RINSE AID INDICATOR

When rinse aid is needed reﬁll, this indicator is on. Reﬁll the rinse aid

to dispenser.

3 IN 1 ICON When select 3 in 1 option.

SALT INDICATOR

When salt is needed reﬁll, this indicator is on. Reﬁll the salt to water

softener.

CHILD LOCK ICON When select Child lock function.

HALF LOAD ICON When select Half load option.

WATER INLET

INDICATOR

When occur water inlet problem. Check the water faucet or water inlet

hose.

DD81-01446E-03_EN_160125.indd 7DD81-01446E-03_EN_160125.indd 7 2016-01-25  2:32:202016-01-25  2:32:20

8_ installing your dishwasher

Installing your dishwasher

WARNING : Electrical shock hazard

Disconnect electrical power before installing dishwasher.

Failure to do so could result in death or electrical shock.

ATTENTION: The installation of the pipes and electrical equipments should be done by professionals.

About electricity connecting

CAUTION, for personal safety:

DO NOT USE AN EXTENSION CORD OR AN ADAPTER PLUG WITH THIS APPLIANCE.

DO NOT, UNDER ANY CIRCUMSTANCES, CUT OR REMOVE THE THIRD GROUNDING

PRONG FROM THE POWER CORD.

Electrical requirements

• An AC 220-240 V / 50 Hz fuse or a circuit breaker.

• An individual branch circuit serving your dishwasher.

Grounding instructions

Insure proper ground exists before use

This appliance must be grounded. In the event of a malfunction or breakdown, grounding

will reduce the risk of electric shock by providing a path of least resistance of electric

current. This appliance is equipped with a cord having an equipment-grounding conductor

and a grounding plug. The plug must be plugged into an appropriate outlet that is installed

and grounded in accordance with all local codes and ordinances.

WARNING: Improper connection of the equipment grounding conductor can result in the

risk of an electric shock. Check with a qualiﬁed electrician or service representative if you

are in doubt whether the appliance is properly grounded. Do not modify the plug provided

with the appliance.

DD81-01446E-03_EN_160125.indd 8DD81-01446E-03_EN_160125.indd 8 2016-01-25  2:32:202016-01-25  2:32:20

installing your dishwasher _9

02 INSTALLING

WATER SUPPLY AND DRAIN

Cold water connection

Connect the cold water supply hose to a threaded 3/4 (inch) connector

and make sure that it is fastened tightly in place.

If the water pipes are new or have not been used for an extended period

of time, let the water run to make sure that the water is clear and free of

impurities. If this precaution is not taken, there is a risk that the water inlet

can get blocked and damage the appliance.

Provided water supply hose has the aqua-safe system. Ensure that

water supply hose’s aqua-safe pipe is connected to the faucet.

Hot water connection

The water supply to the appliance can also be connected to the house hot water line (centralized

system, heating system), as long as it does not exceed a temperature of 60 °C. In this case, the

wash cycle time will be shortened by about 15 minutes and the wash eciency slightly reduced.

The connection must be made to the hot water line following the same procedures as those for

the connection to the cold water line.

Positioning the appliance

Position the appliance in the desired location. The back should rest against the wall behind

it, and the sides, along the adjacent cabinets or wall. The dishwasher is equipped with

water supply and drain hoses that can be positioned to the right or the left to facilitate

proper installation.

How to drain excess water from hoses

If the sink is 1000mm higher from the ﬂoor, the excess water in hoses cannot be drained directly

into the sink. It will be necessary to drain excess water from hoses into a bowl or suitable

container that is held outside and lower than the sink.

Water outlet

Connect the water drain hose. The drain hose must be correctly ﬁtted to avoid water leaks.

Ensure that the water inlet hose is not kinked or squashed.

Extension hose

If you need a drain hose extension, Use a similar size and quality drain hose.

It must be no longer than 4 metres; otherwise the cleaning eect of the dishwasher could be

reduced.

Syphon connection

The waste connection must be at a height of between 40 cm (minimum) and 100 cm (maximum)

from the bottom of the dishwasher. The water drain hose should be ﬁxed by a hose clip.

Aqua-safe

The Aqua-safe System is a safety valve system, preventing water leaks. If the water inlet hose

starts to leak anytime, the safety valve cuts o the running water. If the water inlet hose or the

safety valve is damaged, remove & replace it.

Do not enlarge or shorten the inlet hose.

DD81-01446E-03_EN_160125.indd 9DD81-01446E-03_EN_160125.indd 9 2016-01-25  2:32:202016-01-25  2:32:20

10_ installing your dishwasher

CONNECTION OF DRAIN HOSES

Insert the drain hose into a drain pipe with a minimum diameter of 4cm, or let it run into the sink, making

sure to avoid bending or crimping it. The top of the hose must be at a height between 40 and 100 cm. The

free end of the hose must not be immersed in water to avoid the back ﬂow of it.

POSITION THE APPLIANCE

Position the appliance in the desired location. The back should rest against the wall behind it, and the sides,

along the adjacent cabinets or walls. The dishwasher is equipped with water supply and drain hoses that

can be positioned either to the right or the left sides to facilitate proper installation.

Levelling the Appliance

Once the appliance is positioned for levelling, the height of the

dishwasher may be altered via adjustment of the screwing level of the

feet. In any case, the appliance should not be inclined more than 2°.

START OF DISHWASHER

The followings should be checked before starting the dishwasher.

1. the dishwasher is level and ﬁxed.

2. the inlet valve is opened.

3. there leakage at the connections of the conducts.

4. the wires are tightly connected.

5. the power is switched on.

6. the inlet and drain hoses are not knotted.

7. All packing materials and printings should be taken out from the dishwasher.

ATTENTION: After installation please put this manual in a safe place. The contents of this manual can

be useful to users.

Installing your dishwasher

NOTE

The top of the hose must

be at a height between 40

and 100cm.

The free end of the hose

must not be immersed in

water.

Drain pipe

40 mm

Counter

Min. 400 mm

Max 1000 mm

DD81-01446E-03_EN_160125.indd 10DD81-01446E-03_EN_160125.indd 10 2016-01-25  2:32:202016-01-25  2:32:20

using the detergent and water softener _11

03 DETERGENT AND WATER SOFTENER

Using the detergent and water

softener

WATER SOFTENER

The water softener must be set manually, using the water hardness dial.

The water softener is designed to remove minerals and salts from the water, which would have a detrimental

or adverse eect on the operation of the appliance. The higher the content of these minerals and salts, the

harder your water is. The softener should be adjusted according to the hardness of the water in your area.

Your local Water Authority can advise you on the hardness of the water in your area.

Adjusting salt consumption

The dishwasher is designed to allow for adjusting the amount of salt consumed based on the

hardness of the water used. This is intended to Spelling - optimise - customise the level of salt

consumption so that the salt consumption could be set proceed as follows:

1. Switch on the appliance;

2. Press the Start/Pause button for more than 3 seconds to start the water softener set model

within 60seconds after the appliance was switched on;

3. Press the Start/Pause button to select the proper set according to your local environment,

the sets will change in the following sequence: H1->H2->H3->H4->H5->H6; It is

recommended that adjustments should be made in accordance with the following table.

* The manufactory setting: H4 (SANS 50242)

4. Wait for 5 seconds to end the set up model.

WATER HARDNESS

Selector Position

Salt consumption

(gram/cycle)

Autonomy

(cycles/1 kgs)

º dH º fH º Clark mmol/l

0~5 0~9 0~6 0~0.94 H1 0 /

6~11 10~20 7~14 1.0~2.0 H2 20 60

12~17 21~30 15~21 2.1~3.0 H3 30 50

18~22 31~40 22~28 3.1~4.0 H4 40 40

23~34 41~60 29~42 4.1~6.0 H5 50 30

35~55 61~98 43~69 6.1~9.8 H6 60 20

1 dH (German degree) = 0.178 mmol/l

1 Clark (British degree) = 0.143 mmol/l

1 fH (French degree) = 0.1 mmol/l

Contact your local water board for information on the hardness of your water supply.

WATER SOFTENER

The hardness of the water varies from place to place. If hard water is used in the

dishwasher, deposits may form on dishes and utensils. The appliance is equipped with a

special softener that uses a salt speciﬁcally designed to eliminate lime and minerals from the

water.

DD81-01446E-03_EN_160125.indd 11DD81-01446E-03_EN_160125.indd 11 2016-01-25  2:32:202016-01-25  2:32:20

12_ using the detergent and water softener

Using the detergent and water

softener

LOADING THE SALT INTO THE SOFTENER

Always use salt intended for use with dishwasher.

The salt container is located beneath the lower rack and should be ﬁlled as follows:

ATTENTION

• Only use salt speciﬁcally designed for use in dishwashers! All other types of salt not speciﬁcally

designed for use in a dishwasher, especially table salt, will damage the water softener. In case of

damages caused by the use of unsuitable salt the manufacturer does not give any warranty nor is

liable for any caused damages.

• Only ﬁll with salt just before starting one of the complete washing programs. This will prevent any

grains of salt or salty water, which may have been split, remaining of the bottom of the machine for

any period of time, which may cause corrosion.

• After the ﬁrst wash cycle the control panel light expires.

1. Remove the lower basket and then unscrew and remove the cap from

the salt container.

Open

2. If you are ﬁlling the container for the ﬁrst time, ﬁll 2/3 of its volume with water (around 1 liter).

3. Place the end of the funnel (supplied) into the hole and introduce about

1,5 kg of salt. It is Normal for a small amount of water to come out of

the salt container.

4. Carefully screw the cap back on.

5. Usually, the salt warning light will be o after the salt container be ﬁlled with salt.

• The salt container must be reﬁlled when the salt warning light in the control panel comes on.

Though the salt container is ﬁlled enough, the indicator light may not light may not switch o until

the salt fully dissolves.

If there is no salt warning light in the control panel, you can judge when to load the salt into the

softener by the cycles that the dishwasher has run.

• If a lot of salt is spilt inside the dishwasher run a pre wash program to clan the spillage.

DD81-01446E-03_EN_160125.indd 12DD81-01446E-03_EN_160125.indd 12 2016-01-25  2:32:212016-01-25  2:32:21

using the detergent and water softener _13

03 DETERGENT AND WATER SOFTENER

FILL THE RINSE AID DISPENSER

Function of rinse aid

Rinse aid is automatically added during the last rinse, ensuring thorough rinsing, and spot and

streak free drying.

ATTENTION: Only use branded rinse aid for dishwasher. Never ﬁll the rinse aid dispenser

with any other substances (e.g. dishwasher cleaning agent, liquid detergent). This would

damage the appliance.

When to reﬁll the rinse aid dispenser

If there is no rinse-aid warning light in the control panel, you can judge the amount of rinse-aid by

the Colour of the optical level indicator “D” located next to the cap. When the rinse-aid container

is full, the whole indicator will be dark. As the rinse-aid diminishes, the size of the dark dot

decreases. You should never let the rinse aid get below 1/4 full.

As the rinse aid diminishes, the size of the black dot

on the rinse aid level indicator changes, as illustrated

below.

Full

3/4 full

1/2 full

1/4 full : Should reﬁll to eliminate spotting

Empty

D (Rinse-Aid indicator)

DD81-01446E-03_EN_160125.indd 13DD81-01446E-03_EN_160125.indd 13 2016-01-25  2:32:212016-01-25  2:32:21

14_ using the detergent and water softener

Rinse Aid dispenser

1. To open the dispenser, turn the cap to the “open” (left) arrow

and lift it out.

2. Pour the rinse aid into the dispenser, being careful not to

overﬁll.

3. Replace the cap by inserting it aligned with “open” arrow

and turning it to the closed (right) arrow.

The rinse aid is released during the ﬁnal rinse to prevent water from forming droplets on your

dishes that can leave spots and streaks. It also improves drying by allowing water to water to run

o the dishes.

Your dishwashers is designed to use liquid rinse aids. The rinse aid dispenser is located inside

the door next to the detergent dispenser. To ﬁll the dispenser, open the cap and pour the rinse

aid into the dispenser until the level indicator turns completely black. The volume of the rinse aid

container is about 130 ml.

Be careful not to overﬁll the dispenser, because this could cause over sudsing. Wipe away any

spills with a damp cloth. Don’t forget to replace the cap before you close dishwasher door.

ATTENTION: Clean up any rinse aid spilt during ﬁlling with an absorbent cloth to avoid

excess foaming during the next wash.

Adjusting rinse aid dispenser

The rinse aid dispenser has four settings. Always start with the

dispenser set on “3”. If spots and poor drying are problems,

increase the amount of rinse aid dispensed by removing the

dispenser lid and rotating the dial to “4”. We suggest you to set

on “3” (Factory value is “3”).

Increase the dose if there are drops of water or lime spots on the dishes after washing.

Reduce it if there are sticky whitish streaks on the dishes or a bluish ﬁlm on glassware or

knife blades.

Using the detergent and water

softener

DD81-01446E-03_EN_160125.indd 14DD81-01446E-03_EN_160125.indd 14 2016-01-25  2:32:212016-01-25  2:32:21

using the detergent and water softener _15

03 DETERGENT AND WATER SOFTENER

FUNCTION OF DETERGENT

Detergents with its chemical ingredients are necessary to remove dirt, crush dirt and transport it out of the

dishwasher. Most of commercial quality detergents are suitable for this purpose.

WARNING: Dishwasher detergent is corrosive! Take care to keep it out of reach of children.

Proper Use of Detergent

Use only detergent speciﬁcally made for use in dishwashers. Keep your detergent fresh and dry. Don’t

put powder detergent into the dispenser until you’re ready to wash dishes.

Concentrated detergent

Based on their chemical composition, dishwasher detergent can be split in two basic types:

• conventional, alkaline detergents with caustic components

• low alkaline concentrated detergents with natural enzymes

The use of “normal” washing programmes in conjunction with concentrated detergents reduces

pollution and is good for your dishes; these wash programmes are specially matched to the

dirt-dissolving properties of the enzymes of the concentrated detergent. For this reason “normal”

wash programmes in which concentrated detergents are used can achieve the same results that

can otherwise only be achieved using “intensive” programmes.

Detergent tablets

Detergent tablets of dierent brands dissolve at dierent speeds. For this reason some detergent

tablets cannot dissolve and develop their full cleaning power during short programmes.

Therefore please use long programmes when using detergent tablets, to unsure the complete

removal of detergent residuals.

Detergent dispenser

The dispenser must be reﬁlled before the start of each wash cycle following the instructions

provided in the Wash Cycle Table. Your dishwasher uses less detergent and rinse aid then

conventional dishwashers. Generally, only one tablespoon of detergent is needed for a normal

wash load. Also, more heavily soiled items need more detergent. Always add the detergent just

before starting the dishwasher, otherwise it could get damp and will not dissolve properly.

Fill the detergent in dispenser

1. If the lid is closed: press release button. The lid springs

open.

Push latch to open

2. Always add the detergent just before starting each

wash cycle. Only use branded detergent aid for

dishwasher.

DD81-01446E-03_EN_160125.indd 15DD81-01446E-03_EN_160125.indd 15 2016-01-25  2:32:212016-01-25  2:32:21

16_ using the detergent and water softener

Using the detergent and water

softener

Amount of detergent to use

1. Fill the detergent dispenser with detergent.

The marking indicates the dosing levels, as illustrated on

right:

A. This section is for main wash detergent, approximately

25g

B. This section is for the pre wash detergent,

approximately 5g

If the dishes are heavily soiled, place an additional

detergent dose in the pre-wash detergent chamber. This

detergent will take eect during the pre-wash phase.

You can ﬁnd information about the amount of detergent

for the single programmes on the “Wash cycle table”.

(See page 23)

Please be aware, that according to the soiling level and

the speciﬁc hardness of water dierences are possible.

A

B

2. Close the lid and press until it locks in place.

Please observe the manufacturers dosing and storage recommendations as stated on the

detergent packaging.

Detergents

There are 3 sorts of detergents.

1. With phosphate and with chlorine.

2. With phosphate and without chlorine.

3. Without phosphate and without chloride.

Normally new pulverised detergent is without phosphate. The water softener function of

phosphate is not given. In this case we recommend to ﬁll salt in the salt container even when the

hardness of water is only 6 dH. If detergents without phosphate were used in case of hard water

often white spots appear at dishes and glasses. In this case please add more detergent to reach

better results. Detergents without chlorine do only bleach a little. Strong and coloured spots will

not removed completely. In this case please choose a programme with higher temperature.

DD81-01446E-03_EN_160125.indd 16DD81-01446E-03_EN_160125.indd 16 2016-01-25  2:32:212016-01-25  2:32:21

using the detergent and water softener _17

03 DETERGENT AND WATER SOFTENER

HOW TO USE THE 3 IN 1 OPTION

Your dishwasher has a 3 in 1 option which does not need salt and rinse aid but a 3 In1 tablet. This option

can select on Intensive, Auto or Eco program only.

The 3 in 1 setting is only for use with 3 in 1 tablets. If using 3 in 1 tablet without this option, the

appliance will not get it’s best performance.

1. Put the 3 in 1 tablet into the container then start the 3 in 1 option.

2. Close the lid and press until it locks in place.

When using 3 in 1 compact combination detergents ensure that

the lid can be closed correctly.

ATTENTION: Keep all detergents in a safe place out of

children’s reach. Always add the detergent in the dispenser just

before starting the dishwasher.

DD81-01446E-03_EN_160125.indd 17DD81-01446E-03_EN_160125.indd 17 2016-01-25  2:32:212016-01-25  2:32:21

18_ loading the dishwasher racks

Loading the dishwasher racks

For best performance of the dishwasher, follow these loading guidelines.

Features and appearance of racks and silverware baskets may vary from your

model.

Attention before or after loading the dishwasher racks

Scrape o any large amounts of leftover food. It is not necessary to rinse the dishes under running

water. Place objects in the dishwasher in the following order:

1. Items such as cups, glasses, pots/pans, etc. are stood upside down.

2. Curved items, or those with recesses, should be at a slant so that water can run o.

3. They are stacked securely and can not tip over.

4. They do not prevent the spray arms from rotating while washing takes place.

Very small items should not be washed in the dishwasher as they could easily fall out of the racks.

Removing the dishes

To prevent water dripping from the upper basket into the lower basket, we recommend that you empty

the lower basket ﬁrst and then the upper basket.

LOADING THE UPPER BASKET

The upper basket is designed to hold more delicate and lighter dishware such as glasses, coee and tea

cups and saucers, as well as plates, small bowls and shallow pans (as long as they are not too dirty).

Position the dishes and cookware so that they will not get moved by the spray of water. Always place

glasses, cups & bowls upside down.

1

3

1

2

4

5

6

1

IN

Cups

1

2

Saucers

3

Glasses

4

Small serving bowl

5

Medium serving bowl

6

Large serving bowl

Adjusting the Upper Basket

The height of the upper basket can be adjusted in order to create more space for large utensils

both for the upper/lower basket.

1. To lower the upper rack, press the “A”

levers located at the left and right sides

of the upper basket and push the upper

basket downwards slightly at the same

time.

2. To raise the upper rack, just pull the

upper basket upwards without operating

any levers.

Caution: We recommend adjusting

the height of the upper basket before

loading dishes into the basket. If you

adjust the the basket after loading the

dishes, you may damage the dishes.

To lower position To upper position

A

DD81-01446E-03_EN_160125.indd 18DD81-01446E-03_EN_160125.indd 18 2016-01-25  2:32:222016-01-25  2:32:22

loading the dishwasher racks _19

04 LOADING THE RACKS

LOADING THE LOWER BASKET

We recommend that you place large items which are most dicult to clean in to the lower rack: pots, pans,

lids, serving dishes and bowls, as shown in the ﬁgure to the right.

It is preferable to place serving dishes and lids on the side of the racks in order to avoid blocking the

rotation of the top spray arm. Pots, serving bowls, etc. must always be placed top down.

Deep pots should be slanted to allow water to ﬂow out.

The bottom rack feature fold down tine rows so that larger or more pots and pans can be loaded.

IN

7

Dessert dishes

8

Dinner plates

IN

9

Soup plates

10

Oval platter

Long items, serving cutlery, salad servers and big knives should be placed on the shelf so that they do

not obstruct the rotation of the spray arms.

FOLDING SPIKES OF LOWER BASKET

For better stacking of pots and pans, the spikes can be folded down

as show in the picture right.

DD81-01446E-03_EN_160125.indd 19DD81-01446E-03_EN_160125.indd 19 2016-01-25  2:32:252016-01-25  2:32:25

20_ loading the dishwasher racks

CUTLERY(SILVERWARE) BASKET

Silverware should be placed in the cutlery basket with handles at the bottom: The spoon should be loaded

individually into the appropriate slots, especially long utensils should be placed in the horizontal position at

the front of the upper basket.

1 Soup spoons 5 Dessert spoons

2 Forks 6 Serving spoons

3 Knives 7 Serving forks

4 Teaspoons 8 Gravy ladles

WARNING

• Do not let any item extend through the bottom.

• Always load sharp utensils with the sharp point down!

Loading the dishwasher racks

DD81-01446E-03_EN_160125.indd 20DD81-01446E-03_EN_160125.indd 20 2016-01-25  2:32:292016-01-25  2:32:29

Page is loading ...

Samsung DW-FN320T/XFA User manual

This manual is also suitable for

Samsung DW-FN320T/XFA User manual

in other languages

Related papers

Other documents