The t.racks DSP 26 Owner's manual

DSP 26

digital speaker

management system

user manual

Musikhaus Thomann

Thomann GmbH

Hans-Thomann-Straße 1

96138 Burgebrach

Germany

Telephone: +49 (0) 9546 9223-0

E-mail: [email protected]

Internet: www.thomann.de

29.06.2017, ID: 341074 (V2)

Table of contents

1 General notes............................................................................................................................................... 5

1.1 Further information........................................................................................................................... 6

1.2 Notational conventions.................................................................................................................... 7

1.3 Symbols and signal words............................................................................................................... 8

2 Safety instructions.................................................................................................................................. 10

3 Features....................................................................................................................................................... 14

4 Installation and starting up................................................................................................................ 15

5 Connections and controls................................................................................................................... 16

6 Operating.................................................................................................................................................... 21

6.1 UTILITY menu.................................................................................................................................... 22

6.2 INPUT A/B menu............................................................................................................................... 35

6.3 OUTPUT 1/2/3/4/5/6 menu.......................................................................................................... 41

6.4 Channel linkage................................................................................................................................ 48

6.5 Reset to factory defaults................................................................................................................ 48

7 Technical specifications....................................................................................................................... 50

Table of contents

DSP 26

3

8 Plug and connection assignment.................................................................................................... 52

9 Cleaning....................................................................................................................................................... 54

10 Protecting the environment.............................................................................................................. 55

Table of contents

digital speaker management system

4

1 General notes

This manual contains important instructions for the safe operation of the unit. Read and follow

the safety instructions and all other instructions. Keep the manual for future reference. Make

sure that it is available to all those using the device. If you sell the unit please make sure that

the buyer also receives this manual.

Our products are subject to a process of continuous development. Thus, they are subject to

change.

General notes

DSP 26

5

1.1 Further information

On our website (www.thomann.de) you will find lots of further information and details on the

following points:

Download This manual is also available as PDF file for you to download.

Keyword search

Use the search function in the electronic version to find the topics of

interest for you quickly.

Online guides

Our online guides provide detailed information on technical basics

and terms.

Personal consultation For personal consultation please contact our technical hotline.

Service

If you have any problems with the device the customer service will

gladly assist you.

General notes

digital speaker management system

6

1.2 Notational conventions

This manual uses the following notational conventions:

The letterings for connectors and controls are marked by square brackets and italics.

Examples: [VOLUME] control, [Mono] button.

Texts and values displayed on the device are marked by quotation marks and italics.

Examples: ‘24ch’, ‘OFF’.

References to other locations in this manual are identified by an arrow and the specified page

number. In the electronic version of the manual, you can click the cross-reference to jump to

the specified location.

Example: See

Ä

‘Cross-references’ on page 7.

Letterings

Displays

Cross-references

General notes

DSP 26

7

1.3 Symbols and signal words

In this section you will find an overview of the meaning of symbols and signal words that are

used in this manual.

Signal word Meaning

DANGER! This combination of symbol and signal word indicates an

immediate dangerous situation that will result in death or

serious injury if it is not avoided.

CAUTION! This combination of symbol and signal word indicates a pos‐

sible dangerous situation that can result in minor injury if it

is not avoided.

NOTICE! This combination of symbol and signal word indicates a pos‐

sible dangerous situation that can result in material and

environmental damage if it is not avoided.

General notes

digital speaker management system

8

Warning signs Type of danger

Warning – high-voltage.

Warning – danger zone.

General notes

DSP 26

9

2 Safety instructions

This device serves sound control and distribution of incoming audio signals to the connected

speakers. Use the device only as described in this user manual. Any other use or use under

other operating conditions is considered to be improper and may result in personal injury or

property damage. No liability will be assumed for damages resulting from improper use.

This device may be used only by persons with sufficient physical, sensorial, and intellectual

abilities and having corresponding knowledge and experience. Other persons may use this

device only if they are supervised or instructed by a person who is responsible for their safety.

DANGER!

Danger for children

Ensure that plastic bags, packaging, etc. are disposed of properly and are not

within reach of babies and young children. Choking hazard!

Ensure that children do not detach any small parts (e.g. knobs or the like) from

the unit. They could swallow the pieces and choke!

Never let children unattended use electrical devices.

Intended use

Safety

Safety instructions

digital speaker management system

10

DANGER!

Electric shock caused by high voltages inside

Within the device there are areas where high voltages may be present. Never

remove any covers.

There are no user-serviceable parts inside.

Do not use the device if covers, protectors or optical components are missing or

damaged.

DANGER!

Electric shock caused by short-circuit

Always use proper ready-made insulated mains cabling (power cord) with a pro‐

tective contact plug. Do not modify the mains cable or the plug. Failure to do so

could result in electric shock/death or fire. If in doubt, seek advice from a regis‐

tered electrician.

Safety instructions

DSP 26

11

CAUTION!

Possible hearing damage

With loudspeakers or headphones connected, the device can produce volume

levels that may cause temporary or permanent hearing impairment.

Do not operate the device permanently at a high volume level. Decrease the

volume level immediately if you experience ringing in your ears or hearing

impairment.

NOTICE!

Risk of fire

Do not block areas of ventilation. Do not install the device near any direct heat

source. Keep the device away from naked flames.

Safety instructions

digital speaker management system

12

NOTICE!

Operating conditions

This device has been designed for indoor use only. To prevent damage, never

expose the device to any liquid or moisture. Avoid direct sunlight, heavy dirt, and

strong vibrations.

NOTICE!

Power supply

Before connecting the device, ensure that the input voltage (AC outlet) matches

the voltage rating of the device and that the AC outlet is protected by a residual

current circuit breaker. Failure to do so could result in damage to the device and

possibly injure the user.

Unplug the device before electrical storms occur and when it is unused for long

periods of time to reduce the risk of electric shock or fire.

Safety instructions

DSP 26

13

3 Features

n Two input channels

n Six output channels

n Digital 24-bit signal processors

n RS485 interface

n USB port

n Suitable for installation in 19-inch racks (1 RU)

Features

digital speaker management system

14

4 Installation and starting up

Unpack and carefully check that there is no transportation damage before using the unit. Keep

the equipment packaging. To fully protect the device against vibration, dust and moisture

during transportation or storage use the original packaging or your own packaging material

suitable for transport or storage, respectively.

Create all connections while the device is off. Use the shortest possible high-quality cables for

all connections. Take care when running the cables to prevent tripping hazards.

The unit has been designed for rack mounting in a standard 19-inch rack; it occupies one rack

unit.

Rack mounting

Installation and starting up

DSP 26

15

5 Connections and controls

Front panel

Connections and controls

digital speaker management system

16

1 Display

2 [NAV/PM1]

Rotary switch for setting of values in submenus.

3 [PM2]

Rotary switch for setting of values in submenus.

4 [PM3]

Rotary switch for setting of values in submenus.

5 [ENTER]

Button to confirm changes and input values.

6 [ESC]

Button to exit an open menu or a menu function.

7 [UTILITY]

Button to open the menu for setting the device parameters.

Connections and controls

DSP 26

17

8 LED display input channel A / B

The LEDs show the level of the input signal.

[A], [B]

Briefly pressing the button activates the edit mode for the input channel A and/or B, and the corresponding [EDIT]

LED lights up blue. Changes always affect all active channels.

Hold down the buttons for a second to mute the input channel A or B. In this case, the [MUTE] LED lights up red.

Hold down the buttons again for a second to switch the input channel A or B back on. The [MUTE] LED goes out.

9 LED display output channel 1 to 6

The LEDs show the level of the input signal or the response of the limiter.

[1] … [6]

Briefly pressing the button activates the edit mode for the output channel 1 … 6. In this case, the [EDIT] LED lights up.

Changes always affect all active channels.

Hold down the buttons for a second to mute the output channel 1 … 6. In this case, the [MUTE] LED lights up red.

Hold down the buttons for a second to switch the output channel 1 … 6 back on. The [MUTE] LED goes out.

10 USB port

Connections and controls

digital speaker management system

18

Rear panel

Connections and controls

DSP 26

19

11 Mains switch to turn the device on and off.

12 IEC chassis plug with fuse holder for the power supply.

13 [MAIN | LIFT | GND]

Switch to disconnect the signal ground from the chassis ground to avoid hum loops.

14 [RS485 OUT | IN]

RS485 interface with output for looping through the signal to other devices.

15 [USB/RS485 | LIFT | GND]

Switch to disconnect the signal ground from the USB or RS485 interface to avoid hum loops.

16 [OUTPUTS]

Signal output 6 to 1 (XLR panel connector).

17 [INPUTS]

Signal input B and A (XLR panel socket).

Connections and controls

digital speaker management system

20

Page is loading ...

The t.racks DSP 26 Owner's manual

The t.racks DSP 26 Owner's manual

Related papers

Other documents