GB PROGRAMME CHART
The wool/handwash cycle of this machine has been tested and approved by The Woolmark Company for the washing of
Woolmark garments labelled as “machine wash” or “hand wash” provided that the garments are washed according to the
instructions on the garment label and those issued in this programme chart. M0702
❉
:
optional / Yes : dosing required
1)
For improved garment care, spin speed is restricted in these programmes.
5019 401 05545
Programme
Tempe-
rature
Care
Labels
Max.
Load
kg
Type of wash/Notes
- Respect the manufacturer’s recommendations on the care label
Detergents and additives Special options Dosing
aid
Dosier-
hilfe
Start
delay
Start-
vorwahl
Spin
Pre-
wash
Main
wash
Softener Soil level
Verschm utz ungs-
grad
Clean +
Clean +
Tumble
fresh
Auflockern
Intensive
rinse
Intensiv
spülen
Pre-
wash
Vor-
wäsche
Easy
ironing
Leicht-
bügeln
Spin
Schleu-
dern
Max.
Spin
Speed
rpm
Mixed Mix
20 - 60 6.0
Slightly to normally soiled robust laundry made of cotton, linen, artificial fibres and their blends.
Effective one-hour program. Make sure to wash only similar colours together in one
wash load. If soil level requires, add oxygen-based stain removers.
—
Yes
❉❉
—
❉❉
—
❉❉❉❉
max.
Cotton Koch/Bunt
20 - 95 8.0
Normally to heavily soiled towels, underwear, table and bed linen etc. made of cotton and linen.
❉
Yes
❉❉❉❉❉❉❉❉❉❉
max.
Synthetics Pflegeleicht
20 - 60 3.5
Normally soiled blouses, shirts, overalls, etc. made of polyester (Diolen,
Trevira), polyamide (Perlon, Nylon) or blends with cotton.
❉
Yes
❉❉❉❉❉❉❉❉❉❉
max.
Delicates Fein
20 - 40 2.5
Curtains and delicate clothing, dresses, skirts, shirts and blouses.
❉
Yes
❉❉
—
❉
—
❉
—
❉❉❉
1000
1)
Wool/
Handwash
Wolle/Hand
20 - 40 2.0
Woollens, labelled with the Woolmark and identified as machine washable, as
well as textiles made of silk, linen, wool and viscose marked as handwashable.
This programme is tested and approved by The Woolmark Company for machine- and
handwashable wool.
Select spin speed according to the manufacturer's recommendations on the care label.
—
Yes
❉❉
—
❉
———
❉❉❉
1000
1)
Bedlinen Bettwäsche
20 - 95
3.5
White and coloured bedlinen made of cotton and synthetic fibres, or blends of both.
Reduces microbes and gently cleans, also delicate bedlinen, A thorough rinse phase helps
to prevent detergent and pollen residues. Prefer powder detergent for this programme.
❉
Yes
❉❉
—
❉❉❉❉❉❉❉
max.
White Weiße Wäsche
20 - 60 8.0
Normally to heavily soiled and robust white cotton laundry.
Save energy by selecting a lower wash temperature and adding an oxygen-based bleach
product, in addition to your detergent.
—
Yes
❉❉❉❉❉
—
❉❉❉❉
max.
Light colours Helle Farben
20 - 60 6.0
White and pastel shaded garments made of delicate fabrics.
Gentle wash program to avoid graying or yellowing of your laundry. Use heavy duty detergent, if
necessary also stain removers or bleaches on oxygen basis. Do not use liquid detergent.
❉
Yes
❉❉❉❉
—
❉
—
❉❉❉
1000
1)
Dark
Schwarz &
Dunkel
20 - 60 6.0
Black and dark garments made of cotton, cotton blends and polyester.
Special program to reduce colour fading and local discolouration. Prefer to use a liquid
detergent for dark garments with this program.
❉
Yes
❉❉
—
❉❉❉
—
❉❉❉
1000
1)
Super Eco Super Eco
20 - 60 8.0
Normally to heavily soiled and robust underwear, table and bed linen, towels
and shirts made of cotton and linen.
Offers highest economy in energy consumption by prolonged washing duration. Ideal to
be run overnight to additionally profit from the more favourable energy rates. To avoid
noise of spinning at night, set spin speed to “0” and start spin programme in the morning,
or define programme start with “Start delay” accordingly.
—
Yes
❉❉
—
❉❉
——
❉❉❉
max.
Aqua Eco Aqua Eco
20 - 40 3.0
Lightly soiled laundry made of synthetic fibres, or synthetics mixed with cotton garments.
Saving programme with a very low water consumption. Use liquid detergent and the
lowest recommended amount for 3kg laundry. Do not use softener.
—
Yes
———
❉
———
❉❉❉
max.
Speed 15’ Kurz 15’
20 - 30 3.0
Briefly worn clothing made of cotton, artificial fibers and blends with cotton.
Refresh program. Use lowest recommended detergent amount.
—
Yes
❉
——
❉
———
❉❉❉
max.
Eco Cotton Baumwolle Eco
60 8.0
Heavily soiled and robust laundry washable at 60°C such as bed linen, table linen towels etc.
The extended programme duration enables economic energy and water consumption
while maintaining good washing results.
—
Yes
❉❉
—
❉❉
——
❉❉❉
max.
Rinse & Spin
Spülen &
Schleudern
——
8.0
Rinse and intensive spin programme.
Same as the last rinse and the final spin in the “Cotton” programme.
——
❉
——
❉❉
———
❉❉
max.
A. Programme selector
B. Display
C. “Temperature” button
D. “Spin” button
E. “Dosing Aid” button
F. “Start delay” button
G. “Start (Pause)” button
H. “Reset/Drain” button
I. “Child lock” button combination
Programme sequence indication
“Soil level” indications
“Dosing Aid” indication
“Detergent calibration” indication
“Door open” indication
“Child lock” indication
“Detergent overdosage” indication
Red failure indications
A G
H
F
D
B
I
E
C
Fabrics
Colours
Eco
40105545GB.fm Page 1 Friday, June 25, 2010 11:08 AM
Black process 45.0° 150.0 LPI
5019 401 05545
Add detergent as indicated on the front page and as described in the chapter
“Detergent and Additives” in your Instructions for Use (remove separator in
detergent dispenser for use of powder detergent if necessary).
Turn the programme selector to the desired programme; the light
of the
“Start (Pause)”
button blinks. The
temperature
and
spin speed
indicated on the display can be altered by pressing the
“Temperature” button or the “Spin” button .
When the combination of programme and additional option(s) is
not possible, the indication lights switch off automatically.
Unsuitable combinations of options are deselected automatically.
For certain programmes, an option may already be preset; if you
want you can deselect it.
“Soil level” button
• Adapts the programme duration to the soil level of your
laundry. Also influences the detergent dosing recommendation
when using the “Dosing Aid” button.
= lightly soiled - = normally soiled - = heavily soiled
Not all soil levels are selectable for each programme.
“Clean+” button
• Choose this option if you use an in-wash additive for stain removal
(powder, for example “Vanish”) - it will optimize the additive’s
efficiency to get better wash performance and stain removal.
• Choose temperature of 30 or 40°C and use with maximum load.
• Add an appropriate amount of in-wash additive for stain
removal (powder) to the main wash chamber, together with
your detergent (only use powder detergent with this option).
Respect the manufacturer’s dosing instructions.
• Prolongs the programme by approx. 10 to 15 minutes.
• Appropriate for use of stain removers and bleaches on oxygen
basis.
Chlorine or perborate bleaches must not be used!
“Tumble fresh”
• Select this option if you cannot unload the laundry soon after
programme end, or if you tend to forget the laundry in your
washing machine; it will help to keep your laundry fresh.
• The washing machine will start to tumble the laundry
periodically about one hour after programme end.
• The light of the “Tumble fresh” button will blink while this
function is active, and the display will show “0:01” with
blinking colon.
• The periodic tumbling will last up to approximately 12 hours
after the end of your wash programme, and you can stop it at
any time by pressing the “Tumble fresh” button; it will last a
while until you can open the door.
• After the “tumble fresh” period has run out, the display
indicates “End”.
“Intensive rinse” button
• More water is added and rinse cycle is prolonged.
• This option is particularly suitable for areas with very soft water or
for washing baby linen, and helps people with allergies.
“Prewash” button
• Only for heavily soiled loads (for example sand, granular dirt).
Increases the cycle time by approximately 15 min.
• Do not use liquid detergent for the main wash when activating
the “Prewash” option.
“Easy ironing” button
• Reduces creasing by an increased water quantity and a very
gentle spin.
“Spin” button
• Every programme has a predefined spin speed.
• Press the button to set another spin speed.
- If spin speed “0” is selected, the final spinning is cancelled,
and the water is drained out only. However, intermediate
spin phases remain during rinse.
CONSUMPTION DATA
Programme
Temperature
(°C)
Load
(kg)
Water
(l)
Energy
(kWh)
Approx. Programme Duration
(hours : minutes)
*
Mixed 40 6.0 73 0.60 1:00
Cotton 95 8.0 82
**
2.40 2:10
Cotton 60 8.0 59 1.36 2:20
Cotton 40 8.0 77 0.75 2:05
Synthetics 60 3.5 46
**
0.85 1:35
Synthetics 40 3.5 42 0.50 1:20
Delicates 30 2.5 60 0.40 0:45
Wool/Handwash 40 2.0 45 0.60 0:40
Bedlinen 60 3.5 60 1.30 2:00
White 40 8.0 77 0.85 2:20
Light colours 40 6.0 70 0.50 1:20
Dark 40 6.0 49 0.60 1:40
Super Eco 60 8.0 75 0.95 4:00
Aqua Eco 40 3.0 19 0.45 1:00
Speed 15’ 30 3.0 30 0.20 0:15
Eco Cotton
***
60 8.0 59 1.04 4:00
Consumption values were measured in normalized conditions in compliance with Standard IEC/EN 60 456. Consumption data in the home may vary with respect
to the values in the table in relation to the water supply pressure and temperature, the load and the type of wash.
* The time indicated on the display can deviate from the values in the table, because it takes into account the operation conditions applicable at that time.
** To reduce the water temperature, some cold water is added at the end of the main wash cycle, before the pump drains the water out.
*** Reference Programme for Energy Label (with separator in detergent dispenser removed for use of powder detergent).
ADD DETERGENTS, CLOSE THE DOOR
AND SELECT THE PROGRAMME
SELECT ANY DESIRED OPTION
The “Start delay” allows to run the machine at the consumer’s
convenience, for example at night when electricity is cheaper.
Do not use liquid detergent when activating the “Start delay”.
• Select programme, temperature, spin speed and options.
• Press the Start delay button to select one of the delay time
steps between 0:10 and 23:00 hours.
•Press the
“Start (Pause)”
button ; the light stops
blinking and becomes solid.
The countdown of the delay time begins; the clock symbol next to
the delay time and the colon between hours and minutes blink.
• The time delay indication disappears when the programme
starts and it is replaced by the remaining programme time.
To cancel the “Start delay”
..before you press the “Start (Pause)” button:
• Press the
“Reset/Drain”
button , or set the start delay
time to “0:00” - the delay time disappears after a few seconds.
..after having pressed the “Start (Pause)” button:
•Press the
“Start (Pause)”
button - the delay time
disappears from the display; press
“Start (Pause)”
again to
start the selected programme immediately.
With the “Dosing Aid” button, you can make your washing machine
indicate you the recommended detergent quantity for your wash
load, depending on the soil level selected and the size of the load.
• Helps to save detergent and to protect the environment and
also sensitive skin by avoiding detergent overdosing.
• Before you use this function, save the dosing amounts
recommended for the detergents you use in your washing
machine. Also check if the water hardness in your region
corresponds with the preset “soft” water hardness of the
washing machine; if not you should adapt it.
• Select programme, options and start delay BEFORE using the
“Dosing Aid” button.
For details, refer to the separate “Dosing Aid” Instructions for Use.
Before starting and after end of a programme, the symbol lights to
show that the door can be opened. As long as a wash programme is
running, the door remains locked and must on no account be forced
open. In case you have to open it urgently during a running
programme, refer to “Reset a running programme before the end”.
Open the tap and press the
“Start (Pause)”
button ; the
blinking
“Start (Pause)”
button light becomes constant. The
programme sequence indication shows the current programme
phase, running from left to right through wash, rinse, spin, drain. In
some phases, the remaining programme time is newly calculated - if
this is the case, an animation appears on the display.
Activating the child lock prevents children from starting a wash
cycle or changing the settings of a running programme. The child
lock cannot be activated or deactivated when the programme
selector is in the “Off/O” position. To activate the child lock:
• Turn the programme selector to a programme position, or run
a programme as usual.
• Press and hold the 2 buttons marked with the key symbol
simultaneously for a few seconds. The “Child lock”
symbol on the display will shortly blink and then light
up to indicate that the child lock is active.
The programme setting cannot be changed anymore; the only change
possible is to switch the washer off by turning the programme selector
to the “Off/O” position. To deactivate the child lock, proceed in the
same way as for activating it.
If one of the red failure indications on the display lights up, refer to
the “Troubleshooting Guide” in your “Instructions for Use”.
• The display shows “End”, and the “Door open” indication
lights up.
1. Turn the programme selector to the “Off/O” position.
2. Close the water tap.
3. Open the door and unload the machine.
• Leave the door ajar to allow the drum to dry.
• If you do not turn the programme selector to the “Off/O”
position, all lights of the control panel go out after a few
minutes to save energy - only “End” will remain on the display.
The symbol will light up at the end of the programme if you used
too much detergent. Use less detergent next time. If the symbol
lights up and the display shows “Fod”, too much foam interrupted
the wash process; refer to the “Troubleshooting Guide” in your
Instructions for Use.
1. Press the
“Start (Pause)”
button to pause the
programme. The light blinks.
2. Select the new programme, temperature, any options and
another spin speed if you want.
3. Press the
“Start (Pause)”
button again. The new programme
continues at the same position where the previous programme was
interrupted. Do not add detergent for this programme.
The
“Reset/Drain”
button cancels a programme before the end.
•Press the
“Reset/Drain”
button for at least 3 seconds;
an animation appears on the display. The water is drained out;
it may last a while until the door can be opened.
START DELAY
DETERGENT DOSING
RECOMMENDATION
“DOOR OPEN” INDICATION
PROGRAMME START
CHILD LOCK
RED FAILURE INDICATIONS
PROGRAMME END
DETERGENT OVERDOSAGE INDICATION
CHANGE PROGRAMME AND/OR OPTIONS
AFTER PROGRAMME START
RESET A RUNNING PROGRAMME BEFORE
THE END
The Sensor Technology automatically adapts Programme Time, Water and Energy consumption to the size of your wash load.
40105545GB.fm Page 2 Friday, June 25, 2010 11:08 AM
Black process 45.0° 150.0 LPI
/