Rev-A-Shelf ML-450SC-WS-1 Installation guide

Rev-A-Shelf
Brand
Rev-A-Shelf
Model
ML-450SC-WS-1
Category
Wall & ceiling mounts accessories
Type
Installation guide
This is a spring loaded
product that can cause
severe harm if not handled
properly during installation.
WARNING
TOOLS REQUIRED:
30–45 MIN
ESTIMATED ASSEMBLY TIME:
CARE AND MAINTENANCE:
• Clean with a damp cloth and
wipe parts dry
• Lubricate pivot points as
needed
HEAVY DUTY APPLIANCE LIFT
10
mm
#2
3
mm
A. B.
C.
LEFT & RIGHT
Parts List
No. Description Qty
A 10 g x 16 mm Wood Screws 16
B 10 g x 13 mm Wood Screws 12
C Side-Mounting Brackets (L & R) 2
D Shelf 1
INSTALLATION INSTRUCTIONS: HEAVY DUTY APPLIANCE LIFT I-MLWHSHELF-0118
D.
2
FIGURE A
A. Mark and pre-drill (2) 3 mm pilot holes
13 mm deep into the side support panel.
B. The rst hole should be 32 mm from
the front of cabinet and 114 mm down
from the top of the cabinet.
C. The second hole is parallel to the rst
hole location 267 mm toward rear of
cabinet.
D. Mount the side mounting bracket to
the cabinet support panel by aligning the
back middle hole and the front slot with
the holes that were pre-drilled.
E. Fasten with (2) 10 g x 16 mm wood
screws. Repeat this step for the other
side mount bracket. Wait until Step 5
to install the remaining screws in the
mounting plates to ensure the shelf
surface is level with mixer weight.
NOTE: The distance from top of
cabinet is determined by height and
length of the accessory. 114 mm will
allow adequate clearance for 419 mm
tall stand mixers. Side mounts can be
positioned higher if using lift for smaller
appliances.
STEP 1
INSTALLING SIDE
MOUNTING BRACKETS
DRILL 3 mm PILOT HOLES
267 mm
32 mm
114 mm
ENSURE PROPER
ALIGNMENT
USING A LEVEL
COUNTER TOP
#2
#2
3
mm
3
mm
STEP 2
MOUNTING THE
APPLIANCE LIFT SHELF
NOTE: Holes are pre-drilled to
ensure proper function of the
appliance lift.
From underneath the shelf, line-up the
pre-drilled holes in the shelf with the
slotted holes on the mounting plates.
Insert (6) 10 g x 13 mm wood screws into
the pre-drilled holes, but do not fully
tighten.
(See Fig B).
INSTALLATION INSTRUCTIONS: SHELF MOUNTING WORKSHEET
12400 Earl Jones Way
Louisville, KY 40299
rev-a-shelf.com
Customer Service: 800-626-1126
SHELF MOUNTING WORKSHEET
I-MLSHELF18-1017
NOTE: Holes are pre-drilled to
ensure proper function of the
mixer lift.
From underneath, line-up the
pre-drilled holes in the shelf with
the slotted holes on the mounting
plates. Insert (6) #10 x 1/2” wood
screws into the pre-drilled holes,
but do not fully tighten.
(See Fig A).
Adjust shelf side edges so they are
over the 90-degree bend of the
mounting plate and tighten screws
(See Fig B).
Note: Shelf cannot extend
past the outer surface of the
mounting plate.
This worksheet is for installing
Rev-A-Shelf’s maple or walnut
shelves to their appropriate mixer
lift mechanisms.
Note: Mixer Lift mechanism and
screws packaged separately.
Maple shelf is 11-3/4” x 20” and
designed for 18” face frame
cabinets.
Walnut shelf is 13-1/4” x 20”
and designed for 18” frameless
cabinets.
MOUNTING THE MIXER
LIFT SHELF
STEP 1
STEP 2
From underneath attach (6)
additional #10 x 1/2” (12 mm)
wood screws to remaining
(non-drilled) hole locations to
complete installation.
STEP 3
UNDERSIDE OF
MIXER LIFT SHELF
FRONT EDGE OF
MIXER LIFT SHELF
76 mm
76 mm
216 mm
30 mm
508 mm
PRE-DRILLED HOLE
LOCATIONS
Mounting plate
outer surface
90° bend
327 mm
FIGURE B
3
Place a level on the shelf when
fully extended. With one hand
supporting the shelf, loosen the
screw in the front slots on each of
the cabinet mounting brackets.
The shelf surface should be “nose
up” until the appliance is added.
Once weighted, the shelf will
level out (See Fig D). Once in the
desired location, tighten the front
screws.
Place the appliance on the lift and
check for level in both directions.
Once satised, fasten the (12)
10 g x 16 mm wood screws into
the additional locations on side
mount brackets.
LEVEL ADJUSTMENT
#2
Adjust shelf side edges so they are
over the 90-degree bend of the
mounting plate and tighten screws
(See Fig C).
Note: Shelf cannot extend
past the outer surface of the
mounting plate.
FIGURE D
STEP 3
STEP 5
LOOSEN SCREW
ADJUST VERTICALLY
INSTALLATION INSTRUCTIONS: SHELF MOUNTING WORKSHEET
12400 Earl Jones Way
Louisville, KY 40299
rev-a-shelf.com
Customer Service: 800-626-1126
SHELF MOUNTING WORKSHEET
I-MLSHELF18-1017
NOTE: Holes are pre-drilled to
ensure proper function of the
mixer lift.
From underneath, line-up the
pre-drilled holes in the shelf with
the slotted holes on the mounting
plates. Insert (6) #10 x 1/2” wood
screws into the pre-drilled holes,
but do not fully tighten.
(See Fig A).
Adjust shelf side edges so they are
over the 90-degree bend of the
mounting plate and tighten screws
(See Fig B).
Note: Shelf cannot extend
past the outer surface of the
mounting plate.
This worksheet is for installing
Rev-A-Shelf’s maple or walnut
shelves to their appropriate mixer
lift mechanisms.
Note: Mixer Lift mechanism and
screws packaged separately.
Maple shelf is 11-3/4” x 20” and
designed for 18” face frame
cabinets.
Walnut shelf is 13-1/4” x 20”
and designed for 18” frameless
cabinets.
MOUNTING THE MIXER
LIFT SHELF
STEP 1
STEP 2
From underneath attach (6)
additional #10 x 1/2” (12 mm)
wood screws to remaining
(non-drilled) hole locations to
complete installation.
STEP 3
UNDERSIDE OF
MIXER LIFT SHELF
FRONT EDGE OF
MIXER LIFT SHELF
76 mm
76 mm
216 mm
30 mm
508 mm
PRE-DRILLED HOLE
LOCATIONS
Mounting plate
outer surface
90° bend
327 mm
STEP 4
From underneath the shelf, attach
(6) additional 10 g x 13 mm wood
screws to remaining (non-drilled)
hole locations to complete
installation.
FIGURE C
4
FIGURE F
266 mm
56 mm
570 mm
TENSION
ADJUSTMENT
30 mm
32 mm
IDEAL
MEASUREMENTS
446 mm
39 mm
475 mm
114 mm
112 mm
LOWEST POINT
This appliance lift is equipped
with (3) adjustable spring tension
settings for 0-9 kg, 9- 13 kg, and
13-27 kg. The unit is shipped
with the spring settings set to
the middle setting. To adjust
tension, remove set bolt with a
10 mm open end wrench.
NOTE: DO NOT release holding
tension until after the set bolt
is in the desired location. With
the bolt removed, adjust to the
desired setting. Reinstall the
set bolt, and tighten securely.
Repeat with the opposite side
mounting bracket.
STEP 6
ADJUSTING APPLIANCE
LIFT SPRING TENSION
(REFER TO FIGURES E & F)
FIGURE E
1) 0–9 kg
2) 9–13 kg
3) 13–27 kg
RECOMMENDED SPRING
POSITION FOR VARYING
MIXER WEIGHT
Anything over 27 kg
will void the warranty.
10
mm
! !
WARNING
RELEASING THE 12 MM BOX END WRENCH BEING USED TO HOLD
THE SPRING-LOADED SIDE-MOUNTING BRACKETS BEFORE SECURELY
FASTENING THE REMOVED BOLT CAN CAUSE SERIOUS INJURY
  • Page 1 1
  • Page 2 2
  • Page 3 3
  • Page 4 4

Rev-A-Shelf ML-450SC-WS-1 Installation guide

Rev-A-Shelf
Brand
Rev-A-Shelf
Model
ML-450SC-WS-1
Category
Wall & ceiling mounts accessories
Type
Installation guide
Download PDF
report

Ask a question and I''ll find the answer in the document

Finding information in a document is now easier with AI

Related papers

Other documents