Trinamic TMCM-1617-CANopen Owner's manual

Module for BLDC/PMSM MODULE

TMCM-1617 CANopen®Firmware Manual

Firmware Version V1.06 | Document Revision V1.01 •2021-02-28

The TMCM-1617 is a low-weight miniaturized single axis servo drive for 3-phase BLDC motors with

up to 18A RMS motor current and +24V supply. With CAN, RS485, and EtherCAT®it oﬀers various

communication options. TMCM-1617 supports incremental encoders and digital hall sensors as

position feedback. Customization and diﬀerent housing options are possible.

Features

•Servo drive for BLDC motors

•+8. . . 28V DC supply voltage

•Up to 18A RMS max. motor current

•RS485, CAN & EtherCAT®interfaces

•Incremental encoder feedback

•Digital HALL sensor feedback

•Reference switch inputs

•Cooling via aluminum housing

•L/W/H: 36.8mm x 26.8mm x 11.1mm

•Weight: ca. 24g

•Customization options

Applications

•Robotics

•Laboratory Automation

•Manufacturing

•Factory Automation

•Servo Drives

•Low Inductance Motors

Simpliﬁed Block Diagram

Terms of delivery and rights to technical change reserved.

Download newest version at: www.trinamic.com

Read entire documentation.

TMCM-1617 CANopen®Firmware Manual •Firmware Version V1.06 | Document Revision V1.01 •2021-02-28 2 / 104

Contents

1 Preface 3

1.1 General Features of this CANopen Implementation ......................... 3

1.2 Abbreviations used in this Manual ................................... 4

1.3 Firmware Update ............................................. 4

2 Communication 5

2.1 Reference Model ............................................. 5

2.2 NMT State Machine ............................................ 7

2.3 Device Model ............................................... 8

2.4 Object Dictionary ............................................. 9

3 Communication Area 11

3.1 Detailed Object Speciﬁcations ...................................... 11

3.1.1 Object 1000h: Device Type .................................. 11

3.1.2 Object 1001h: Error Register ................................. 11

3.1.3 Object 1005h: COB-ID SYNC Message ............................ 12

3.1.4 Object 1008h: Manufacturer Device Name ......................... 13

3.1.5 Object 1009h: Manufacturer Hardware Version ...................... 13

3.1.6 Object 100Ah: Manufacturer Software Version ....................... 13

3.1.7 Object 100Ch: Guard Time .................................. 14

3.1.8 Object 100Dh: Life Time Factor ................................ 14

3.1.9 Object 1010h: Store Parameters ............................... 14

3.1.10 Object 1011h: Restore Parameters .............................. 16

3.1.11 Object 1014h: COB-ID Emergency Object .......................... 17

3.1.12 Object 1015h: Inhibit Time EMCY ............................... 17

3.1.13 Object 1016h: Consumer Heartbeat Time .......................... 18

3.1.14 Object 1017h: Producer Heartbeat Time .......................... 18

3.1.15 Object 1018h: Identity Object ................................. 19

3.1.16 Object 1029h: Error Behaviour ................................ 19

3.1.17 Objects 1400h– 1403h: Receive PDO Communication Parameter ............ 20

3.1.18 Objects 1600h– 1603h: Receive PDO Mapping Parameter ................ 21

3.1.19 Objects 1800h– 1803h: Transmit PDO Communication Parameter ........... 22

3.1.20 Objects 1A00h– 1A03h: Transmit PDO Mapping Parameter ............... 23

4 Manufacturer speciﬁc Area 25

4.1 Detailed Object Speciﬁcations ...................................... 25

4.1.1 Object 2000h: Device Info ................................... 25

4.1.2 Object 2003h: Maximum Current .............................. 25

4.1.3 Object 2004h: Open Loop Current .............................. 26

4.1.4 Object 2005h: Limit Switches ................................. 26

4.1.5 Object 2006h: Brake Chopper ................................. 27

4.1.6 Object 2041h: Torque Mode Settings ............................ 28

4.1.7 Object 2042h: Velocity Mode Settings ............................ 28

4.1.8 Object 2043h: Position Mode Settings ............................ 29

4.1.9 Object 2050h: Motor Type ................................... 29

4.1.10 Object 2055h: Commutation Mode ............................. 29

4.1.11 Object 2056h: Motor Pole Pairs ................................ 30

4.1.12 Object 2057h: Motor Shaft Direction ............................. 31

4.1.13 Object 2058h: Position Scaler ................................. 31

4.1.14 Object 2060h: ADC Conﬁguration .............................. 31

4.1.15 Object 2070h: Hall Sensor Settings .............................. 32

4.1.16 Object 2080h: ABN Encoder Settings ............................ 33

Terms of delivery and rights to technical change reserved.

Download newest version at www.trinamic.com

TMCM-1617 CANopen®Firmware Manual •Firmware Version V1.06 | Document Revision V1.01 •2021-02-28 3 / 104

4.1.17 Object 2101h: Motor Status Flags .............................. 33

4.1.18 Object 2102h: Open Loop Commutation Angle ...................... 34

4.1.19 Object 2103h: Encoder Commutation Angle ........................ 35

4.1.20 Object 2104h: Hall Commutation Angle ........................... 35

4.1.21 Object 2140h: Home Oﬀset Display ............................. 36

4.1.22 Object 2702h: Digital Inputs .................................. 36

4.1.23 Object 2703h: Digital Outputs ................................. 36

4.1.24 Object 2704h: CAN Bit Rate .................................. 37

4.1.25 Object 2705h: Node ID ..................................... 38

4.1.26 Object 2706h: Store ...................................... 38

4.1.27 Object 2707h: CAN Bit Rate Load ............................... 38

4.1.28 Object 2708h: Node ID Load ................................. 39

4.1.29 Object 270Eh: Analog Inputs ................................. 39

5 Proﬁle speciﬁc Area 41

5.1 Detailed Object Speciﬁcations ...................................... 41

5.1.1 Object 605Ah: Quick Stop Option Code ........................... 41

5.1.2 Object 605Bh: Shutdown Option Code ........................... 42

5.1.3 Object 605Ch: Disable Operation Option Code ....................... 42

5.1.4 Object 605Dh: Halt Option Code ............................... 43

5.1.5 Object 605Eh: Fault Reaction Option Code ......................... 43

5.1.6 Object 6060h: Modes of Operation ............................. 44

5.1.7 Object 6061h: Modes of Operation Display ......................... 45

5.1.8 Object 60FDh: Digital Inputs ................................. 46

5.1.9 Object 6502h: Supported Drive Modes ........................... 46

6 Proﬁle Position Mode 48

6.1 Detailed Object Speciﬁcations ...................................... 48

6.1.1 Object 6040h: Control Word ................................. 49

6.1.2 Object 6041h: Status Word .................................. 50

6.1.3 Object 6062h: Position Demand Value ........................... 51

6.1.4 Object 6063h: Position Actual Internal Value ........................ 52

6.1.5 Object 6064h: Position Actual Value ............................. 52

6.1.6 Object 6065h: Following Error Window ........................... 53

6.1.7 Object 6067h: Position Window ............................... 53

6.1.8 Object 6068h: Position Window Time ............................ 54

6.1.9 Object 606Ch: Velocity Actual Value ............................. 54

6.1.10 Object 607Ah: Target Position ................................ 55

6.1.11 Object 607Dh: Software Position Limit ........................... 55

6.1.12 Object 6081h: Proﬁle Velocity ................................. 56

6.1.13 Object 6083h: Proﬁle Acceleration .............................. 56

6.1.14 Object 6084h: Proﬁle Deceleration .............................. 57

6.1.15 Object 6085h: Quick Stop Deceleration ........................... 57

6.1.16 Object 60F2h: Positioning Option Code ........................... 57

6.2 How to move a Motor in pp Mode ................................... 58

7 Proﬁle Velocity Mode 59

7.1 Detailed Object Speciﬁcations ...................................... 59

7.1.1 Object 6040h: Control Word ................................. 59

7.1.2 Object 6041h: Status Word .................................. 60

7.1.3 Object 6062h: Position Demand Value ........................... 62

7.1.4 Object 6063h: Position Actual Internal Value ........................ 62

7.1.5 Object 6064h: Position Actual Value ............................. 62

7.1.6 Object 6065h: Following Error Window ........................... 63

Terms of delivery and rights to technical change reserved.

Download newest version at www.trinamic.com

TMCM-1617 CANopen®Firmware Manual •Firmware Version V1.06 | Document Revision V1.01 •2021-02-28 4 / 104

7.1.7 Object 606Ch: Velocity Actual Value ............................. 63

7.1.8 Object 607Dh: Software Position Limit ........................... 64

7.1.9 Object 6083h: Proﬁle Acceleration .............................. 64

7.1.10 Object 6085h: Quick Stop Deceleration ........................... 65

7.1.11 Object 60FFh: Target Velocity ................................. 65

7.2 How to move a Motor in pv Mode ................................... 66

8 Homing Mode 67

8.1 Homing Methods ............................................. 68

8.1.1 Homing Method 17: Homing on negative Limit Switch .................. 68

8.1.2 Homing Method 18: Homing on positive Limit Switch .................. 68

8.1.3 Homing Method 19: Homing on positive Home Switch .................. 69

8.1.4 Homing Method 21: Homing on negative Home Switch ................. 69

8.1.5 Homing Method 35: Current Position as Home Position ................. 70

8.2 Detailed Object Speciﬁcations ...................................... 71

8.2.1 Object 6040h: Control Word ................................. 71

8.2.2 Object 6041h: Status Word .................................. 72

8.2.3 Object 606Ch: Velocity Actual Value ............................. 73

8.2.4 Object 607Ch: Home Oﬀset .................................. 74

8.2.5 Object 6098h: Homing Method ................................ 75

8.2.6 Object 6099h: Homing Speeds ................................ 75

8.2.7 Object 609Ah: Homing Acceleration ............................. 75

8.3 How to start a Homing in hm Mode .................................. 76

9 Cyclic synchronous Position Mode 77

9.1 Detailed Object Speciﬁcations ...................................... 77

9.1.1 Object 6040h: Control Word ................................. 77

9.1.2 Object 6041h: Status Word .................................. 78

9.1.3 Object 6062h: Position Demand Value ........................... 80

9.1.4 Object 6063h: Position Actual Internal Value ........................ 80

9.1.5 Object 6064h: Position Actual Value ............................. 80

9.1.6 Object 606Ch: Velocity Actual Value ............................. 81

9.1.7 Object 607Ah: Target Position ................................ 81

9.1.8 Object 607Dh: Software Position Limit ........................... 82

9.1.9 Object 60B0h: Position Oﬀset ................................. 82

9.1.10 Object 60C2h: Interpolation Time Period .......................... 83

10 Cyclic synchronous Velocity Mode 84

10.1 Detailed Object Speciﬁcations ...................................... 84

10.1.1 Object 6040h: Control Word ................................. 84

10.1.2 Object 6041h: Status Word .................................. 85

10.1.3 Object 606Ch: Velocity Actual Value ............................. 87

10.1.4 Object 60FFh: Target Velocity ................................. 87

10.1.5 Object 607Dh: Software Position Limit ........................... 87

10.1.6 Object 60B1h: Velocity Oﬀset ................................. 88

10.1.7 Object 60C2h: Interpolation Time Period .......................... 88

11 Cyclic synchronous Torque Mode 90

11.1 Detailed Object Speciﬁcations ...................................... 90

11.1.1 Object 6040h: Control Word ................................. 90

11.1.2 Object 6041h: Status Word .................................. 91

11.1.3 Object 6062h: Position Demand Value ........................... 92

11.1.4 Object 6063h: Position Actual Internal Value ........................ 93

11.1.5 Object 6064h: Position Actual Value ............................. 93

11.1.6 Object 6071h: Target Torque ................................. 94

Terms of delivery and rights to technical change reserved.

Download newest version at www.trinamic.com

TMCM-1617 CANopen®Firmware Manual •Firmware Version V1.06 | Document Revision V1.01 •2021-02-28 5 / 104

11.1.7 Object 6077h: Torque actual Value .............................. 94

11.1.8 Object 607Dh: Software Position Limit ........................... 94

11.1.9 Object 60B2h: Torque Oﬀset ................................. 95

11.1.10 Object 60C2h: Interpolation Time Period .......................... 95

12 Emergency Messages (EMCY) 97

13 Figures Index 100

14 Tables Index 101

15 Supplemental Directives 102

15.1 Producer Information ..........................................102

15.2 Copyright ..................................................102

15.3 Trademark Designations and Symbols .................................102

15.4 Target User ................................................102

15.5 Disclaimer: Life Support Systems ....................................102

15.6 Disclaimer: Intended Use ........................................102

15.7 Collateral Documents & Tools ......................................103

16 Revision History 104

16.1 Firmware Revision ............................................104

16.2 Document Revision ............................................104

Terms of delivery and rights to technical change reserved.

Download newest version at www.trinamic.com

TMCM-1617 CANopen®Firmware Manual •Firmware Version V1.06 | Document Revision V1.01 •2021-02-28 6 / 104

1 Preface

This document speciﬁes objects and modes of operation of the Trinamic TMCM-1617 stepper motor con-

trol module with CANopen ﬁrmware. The CANopen ﬁrmware is designed to fulﬁll the CANopen DS402

and DS301 standards. This manual assumes that the reader is already familiar with the basics of the

CANopen protocol, deﬁned by the DS301 and DS402 standards of the CAN-CiA.

If necessary it is always possible to turn the module into a TMCL module by loading the TMCM-1617 TMCL

ﬁmware again through the CAN interface or the RS485 interface, with the help of the ﬁrmware update

function of the TMCL-IDE 3.0.

1.1 General Features of this CANopen Implementation

Main Characteristics

•Communication according to standard CiA-301 V4.1

•CAN bit rate: 20. . . 1000kBit/s

•CAN ID: 11 bit

•Node ID: 1. . . 127 (use vendor speciﬁc objects for changing the node ID)

•NMT services: NMT slave

SDO Communication

•1 server

•Expedited transfer

•Segmented transfer

•No block transfer

PDO Communication

•Producer

•Consumer

•RPDOs

–Axis 0: 1, 2, 3, 4

–Transmission modes: asynchronous.

–Dynamic mapping with max. 3 mapping entries.

–Default mappings: according to CiA-402 for ﬁrst three PDOs of each axis, manufacturer speciﬁc

for other PDOs of each axis.

•TPDOs

–Axis 0: 1, 2, 3, 4

–Transmission modes: asynchronous, asynchronous with event timer, synchronous.

–Dynamic mapping with max. 3 mapping entries.

–Default mappings: according to CiA-402 for ﬁrst three PDOs of each axis, manufacturer speciﬁc

for other PDOs of each axis.

Terms of delivery and rights to technical change reserved.

Download newest version at www.trinamic.com

TMCM-1617 CANopen®Firmware Manual •Firmware Version V1.06 | Document Revision V1.01 •2021-02-28 7 / 104

Further Characteristics

•SYNC: consumer (TPDOs 3 are synchronous PDOs)

•Emergency: producer

•RTR: supported only for node guarding/life guarding

•Heartbeat: consumer and producer

1.2 Abbreviations used in this Manual

Abbreviations

CAN Controller area network

CHGND chassis ground / earth ground

COB Communication object

FSA Finite state automaton

FSM Finite state machine

NMT Network management

ID Identiﬁer

LSB Least signiﬁcant bit

MSB Most signiﬁcant bit

PDO Process data object

PDS Power drive system

RPDO Receive process data object

SDO Service data object

TPDO Transmit process data object

EMCY Emergency object

rw Read and write

ro Read only

hm Homing mode

pp Proﬁle position mode

pv Proﬁle velocity mode

vm Velocity mode

Table 1: Abbreviations used in this Manual

1.3 Firmware Update

The software running on the microprocessor consists of two parts, a boot loader and the CANopen

ﬁrmware itself. Whereas the boot loader is installed during production and testing at TRINAMIC and

remains untouched throughout the whole lifetime, the CANopen ﬁrmware can easily be updated by the

user. The new ﬁrmware can be loaded into the module via the ﬁrmware update function of the TMCL-IDE,

using the CAN interface or the RS485 interface of the module.

Terms of delivery and rights to technical change reserved.

Download newest version at www.trinamic.com

TMCM-1617 CANopen®Firmware Manual •Firmware Version V1.06 | Document Revision V1.01 •2021-02-28 8 / 104

2 Communication

2.1 Reference Model

The application layer comprises a concept to conﬁgure and communicate real-time-data as well as the

mechanisms for synchronization between devices. The functionality which the application layer oﬀers

to an application is logically divided over diﬀerent service data objects (SDO) in the application layer. A

service object oﬀers a speciﬁc functionality and all the related services.

Applications interact by invoking services of a service object in the application layer. To realize these ser-

vices this object exchanges data via the CAN Network with peer service object(s) using a protocol.

The application and the application layer interact with service primitives.

Service Primitives

Primitive Deﬁnition

Request Issued by the application to the application layer to request a service.

Indication Issued by the application layer to the application to report an internal event detected

by the application layer or indicate that a service is requested.

Response Issued by the application to the application layer to respond to a previous received

indication.

Conﬁrmation Issued by the application layer to the application to report the result of a previously

issued request.

Table 2: Service Primitives

A service type deﬁnes the primitives that are exchanged between the application layer and the cooper-

ating applications for a particular service of a service object. Unconﬁrmed and conﬁrmed services are

collectively called remote services.

Terms of delivery and rights to technical change reserved.

Download newest version at www.trinamic.com

TMCM-1617 CANopen®Firmware Manual •Firmware Version V1.06 | Document Revision V1.01 •2021-02-28 9 / 104

Service Types

Type Deﬁnition

Local service Involves only the local service object. The application issues a request to

its local service object that executes the requested service without commu-

nicating with peer service object(s).

Unconﬁrmed service Involves one or more peer service objects. The application issues a request

to its local service object. This request is transferred to the peer service

object(s) that each passes it to their application as an indication. The result

is not conﬁrmed back.

Conﬁrmed service Can involve only one peer service object. The application issues a request

to its local service object. This request is transferred to the peer service

object that passes it to the other application as an indication. The other

application issues a response that is transferred to the originating service

object that passes it as a conﬁrmation to the requesting application.

Provider initiated service Involves only the local service object. The service object (being the service

provider) detects an event not solicited by a requested service. This event

is then indicated to the application.

Table 3: Service Types

Terms of delivery and rights to technical change reserved.

Download newest version at www.trinamic.com

TMCM-1617 CANopen®Firmware Manual •Firmware Version V1.06 | Document Revision V1.01 •2021-02-28 10 / 104

2.2 NMT State Machine

The ﬁnite state machine (FSM) or simply state machine is a model of behavior composed of a ﬁnite number

of states, transitions between those states, and actions. It shows which way the logic runs when certain

conditions are met.

Starting and resetting the device is controlled via the state machine. The NMT state machine consists of

the states shown in ﬁgure 1.

Pre-operational

Operational

Stopped

Initialization

ID / Boot-up

Figure 1: NMT State Machine

After power-on or reset the device enters the Initialization state. After the device initialization is ﬁnished,

the device automatically transits to the Pre-operational state and indicates this state transition by send-

ing the boot-up message. This way the device indicates that it is ready to work. A device that stays in

Pre-operational state may start to transmit SYNC-, time stamp- or heartbeat message. In contrast to the

PDO communication that is disabled in this state, the device can communicate via SDO.

The PDO communication is only possible within the Operational state. During Operational state the de-

vice can use all supported communication objects.

A device that was switched to the Stopped state only reacts on received NMT commands. In addition the

device indicates the current NMT state by supporting the error control protocol during Stopped state.

The transitions between states are made by issuing a network management (NMT) communication object

to the device. The NMT protocols are used to generate state machine change commands (e.g. to start

and stop the device), detect remote device boot-ups and error conditions.

The Heartbeat message of a CANopen device contains the device status of the NMT state machine and is

sent cyclically by the CANopen device.

The NMT state machine (or DS301 state machine) is not to be confused with the DS402 state machine.

There is only one NMT state machine for the entire device, but for each motor there is a DS402 state

machine which controls the motor. There are no links between these state machines, with one exception:

When the NMT state machine is being switched to the stopped state, all DS402 state machines that are in

OPERATION_ENABLED state will be switch to FAULT state.

Terms of delivery and rights to technical change reserved.

Download newest version at www.trinamic.com

TMCM-1617 CANopen®Firmware Manual •Firmware Version V1.06 | Document Revision V1.01 •2021-02-28 11 / 104

Device control state machine

CANopen Communication Profile CiA DS301

NMT State Machine

Modes of operation:

Profile Position (pp)

Profile Velocity (pv)

Homing (hm)

...

CANopen device profile CiA DSP 402

CAN

Figure 2: Communication Architecture

2.3 Device Model

A CANopen device mainly consists of the following parts:

•Communication: This function unit provides the communication objects and the appropriate func-

tionality to transport data items via the underlying network structure.

•Object dictionary: The object dictionary is a collection of all the data items which have an inﬂuence

on the behavior of the application objects, the communication objects and the state machine used

on this device.

•Application: The application comprises the functionality of the device with respect to the interaction

with the process environment.

Terms of delivery and rights to technical change reserved.

Download newest version at www.trinamic.com

TMCM-1617 CANopen®Firmware Manual •Firmware Version V1.06 | Document Revision V1.01 •2021-02-28 12 / 104

Communication Application

Object dictionary

State machine Application

object

Communication

object

Entry 1

Entry 2

Entry n

Bus system Process

Communication

object

Communication

object

Communication

object

Application

object

Application

object

Application

object

Figure 3: Device Model

2.4 Object Dictionary

The most important part of a device proﬁle is the object dictionary description. The object dictionary is

essentially a grouping of objects accessible via the network in an ordered pre-deﬁned fashion. Each object

within the dictionary is addressed using a 16-bit index. The overall layout of the standard object dictionary

is shown in table 4:

Object Dictionary

Index Object

0000hNot used.

0001h– 001FhStatic data types.

0020h– 003FhComplex data types.

0040h– 005FhManufacturer speciﬁc complex data types.

0060h– 007FhDevice proﬁle speciﬁc static data types.

0080h– 009FhDevice proﬁle speciﬁc complex data types.

00A0h– 0FFFhReserved for further use.

1000h– 1FFFhCommunication proﬁle area.

2000h– 5FFFhManufacturer speciﬁc proﬁle area.

6000h– 9FFFhStandardized device proﬁle area.

A000h– BFFFhStandardized interface proﬁle area.

C000h– FFFFhReserved for further use.

Table 4: Object Dictionary

Terms of delivery and rights to technical change reserved.

Download newest version at www.trinamic.com

TMCM-1617 CANopen®Firmware Manual •Firmware Version V1.06 | Document Revision V1.01 •2021-02-28 13 / 104

The communication proﬁle area at indices 1000hthrough 1FFFhcontains the communication speciﬁc pa-

rameters for the CAN network. These entries are common to all devices.

The manufacturer segment at indices 2000hthrough 5FFFhcontains manufacturer speciﬁc objects. These

objects control the special features of the Trinamic TMCM-1617 motion control device.

The standardized device proﬁle area at indices 6000hthrough 9FFFhcontains all data objects common to

a class of devices that can be read or written via the network. They describe the device parameters and

the device functionality of the device proﬁle.

Terms of delivery and rights to technical change reserved.

Download newest version at www.trinamic.com

TMCM-1617 CANopen®Firmware Manual •Firmware Version V1.06 | Document Revision V1.01 •2021-02-28 14 / 104

3 Communication Area

The communication area contains all objects that deﬁne the communication parameters of the CANopen

device according to the DS301 standard.

3.1 Detailed Object Speciﬁcations

3.1.1 Object 1000h: Device Type

This object contains information about the device type. The object 1000hdescribes the type of device

and its functionality. It is composed of a 16-bit ﬁeld which describes the device proﬁle that is used and a

second 16-bit ﬁeld which provides additional information about optional functionality of the device.

Object Description

Index Name Object Type Data Type

1000hDevice type Variable UNSIGNED32

Table 5: Object Description (1000h)

Entry Description

Sub-index Access PDO Mapping Value Range Default Value

0 ro no UNSIGNED32 FFFC0192h

Table 6: Entry Description (1000h)

3.1.2 Object 1001h: Error Register

This object contains error information. The CANopen device maps internal errors into object 1001h. It is

part of an emergency object.

Object Description

Index Name Object Type Data Type

1001hError register Variable UNSIGNED8

Table 7: Object Description (1001h)

Entry Description

Sub-index Access PDO Mapping Value Range Default Value

0 ro no UNSIGNED8 0

Table 8: Entry Description (1001h)

Terms of delivery and rights to technical change reserved.

Download newest version at www.trinamic.com

TMCM-1617 CANopen®Firmware Manual •Firmware Version V1.06 | Document Revision V1.01 •2021-02-28 15 / 104

Error Register Bits

Bit Deﬁnition

0 Generic error

1 Current

2 Voltage

3 Temperature

4 Communication error

5 Device proﬁle speciﬁc

6 Reserved (always 0)

7 Manufacturer speciﬁc

Table 9: Error Register Bits

3.1.3 Object 1005h: COB-ID SYNC Message

This object deﬁnes the COB-ID of the synchronization object (SYNC). Further, it deﬁnes whether the mod-

ule generates the SYNC.

Value Deﬁnition

Bit Name Deﬁnition

30 Generate 0: Device does not generate SYNC message

1: Device generates SYNC message

29 Frame Not supported, always set to 0.

28. . . 11 29 bit ID Not supported, always set to 0.

10. . . 0 11 bit ID 11 bit COB-ID.

Table 10: Value Deﬁnition (1005h)

Object Description

Index Name Object Type Data Type

1005hCOB-ID SYNC message Variable UNSIGNED32

Table 11: Object Description (1005h)

Entry Description

Sub-index Access PDO Mapping Value Range Default Value

0 rw no UNSIGNED32 80h

Table 12: Entry Description (1005h)

Terms of delivery and rights to technical change reserved.

Download newest version at www.trinamic.com

TMCM-1617 CANopen®Firmware Manual •Firmware Version V1.06 | Document Revision V1.01 •2021-02-28 16 / 104

3.1.4 Object 1008h: Manufacturer Device Name

This object contains the name of the device as given by the manufacturer.

Object Description

Index Name Object Type Data Type

1008hManufacturer Device Name Variable Visible String

Table 13: Object Description (1008h)

Entry Description

Sub-index Access PDO Mapping Value Range Default Value

0 ro no — TMCM-1617

Table 14: Entry Description (1008h)

3.1.5 Object 1009h: Manufacturer Hardware Version

This object contains the hardware version description.

Object Description

Index Name Object Type Data Type

1009hManufacturer Hardware Version Variable Visible String

Table 15: Object Description (1009h)

Entry Description

Sub-index Access PDO Mapping Value Range Default Value

0 ro no — Depends on device, e.g. 1.0.

Table 16: Entry Description (1009h)

3.1.6 Object 100Ah: Manufacturer Software Version

This object contains the software version description.

Object Description

Index Name Object Type Data Type

100AhManufacturer Software Version Variable Visible String

Table 17: Object Description (100Ah)

Terms of delivery and rights to technical change reserved.

Download newest version at www.trinamic.com

TMCM-1617 CANopen®Firmware Manual •Firmware Version V1.06 | Document Revision V1.01 •2021-02-28 17 / 104

Entry Description

Sub-index Access PDO Mapping Value Range Default Value

0 ro no — Depends on device, e.g. 1.0.

Table 18: Entry Description (100Ah)

3.1.7 Object 100Ch: Guard Time

The objects at index 100Chand 100Dhshall indicate the conﬁgured guard time respectively the life time

factor. The life time factor multiplied with the guard time gives the life time for the life guarding protocol.

Object Description

Index Name Object Type Data Type

100ChGuard Time Variable UNSIGNED16

Table 19: Object Description (100Ch)

Entry Description

Sub-index Access PDO Mapping Value Range Default Value

0 rw no UNSIGNED16 0

Table 20: Entry Description (100Ch)

3.1.8 Object 100Dh: Life Time Factor

The life time factor multiplied with the guard time gives the life time for the life guarding protocol.

Object Description

Index Name Object Type Data Type

100DhLife Time Factor Variable UNSIGNED8

Table 21: Object Description (100Dh)

Entry Description

Sub-index Access PDO Mapping Value Range Default Value

0 rw no UNSIGNED8 0

Table 22: Entry Description (100Dh)

3.1.9 Object 1010h: Store Parameters

This object supports the saving of parameters in non volatile memory. By read access the device provides

information about its saving capabilities.

Terms of delivery and rights to technical change reserved.

Download newest version at www.trinamic.com

TMCM-1617 CANopen®Firmware Manual •Firmware Version V1.06 | Document Revision V1.01 •2021-02-28 18 / 104

The TMCM-1617 module supports saving of the following parameter groups:

•Sub-index 1h: save all parameters.

•Sub-index 2h: save communication parameters 2704hand 2705h.

•Sub-index 4h: save motor 0 parameters.

Note In order to avoid storage of parameters by mistake, storage is only executed

when a speciﬁc signature is written to the appropriate sub-Index. This signature

is "save" (65766173h, see also table 23).

Save Signature

e v a s

65h76h61h73h

Table 23: Save Signature

On reception of the correct signature in the appropriate sub-index the device stores the parameter and

then conﬁrms the SDO transmission (initiate download response). If the storing failed, the device re-

sponds with an abort SDO transfer (abort code: 06060000h). If a wrong signature is written, the device

refuses to store and responds with abort SDO transfer (abort code: 0800002xh).

On read access, each sub-index provides information if it is possible to store the parameter group. It

reads 1 if yes and 0 if no.

Object Description

Index Name Object Type Data Type

1010hStore Parameters Array UNSIGNED32

Table 24: Object Description (1010h)

Entry Description

Sub-index Description Access PDO Mapping Value Range Default Value

00hHighest supported sub-index ro no UNSIGNED8 4

01hSave all parameters rw no UNSIGNED32 —

02hSave communication parameters rw no UNSIGNED32 —

04hSave motor 0 parameters rw no UNSIGNED32 —

Table 25: Entry Description (1010h)

Terms of delivery and rights to technical change reserved.

Download newest version at www.trinamic.com

TMCM-1617 CANopen®Firmware Manual •Firmware Version V1.06 | Document Revision V1.01 •2021-02-28 19 / 104

3.1.10 Object 1011h: Restore Parameters

With this object the default values of parameters according to the communication or device proﬁle are

restored. By read access the device provides information about its capabilities to restore these values.

The TMCM-1617 module supports restoring of the following parameter groups:

•Sub-index 1h: restore all parameters (factory reset).

•Sub-index 2h: restore communication parameters 2704hand 2705h.

•Sub-index 4h: restore motor 0 parameters.

Note In order to avoid restoring the parameters by mistake, restoring is only executed

when a speciﬁc signature is written to the appropriate sub-Index. This signature

is "load" (64616F6Ch, see also table 26).

Load Signature

d a o l

64h61h6Fh6Ch

Table 26: Load Signature

On reception of the correct signature in the appropriate sub-index the device restores the parameter and

then conﬁrms the SDO transmission (initiate download response). If the restoring failed, the device re-

sponds with an abort SDO transfer (abort code: 06060000h). If a wrong signature is written, the device

refuses to restore and responds with abort SDO transfer (abort code: 0800002xh).

On read access, each sub-index provides information if it is possible to restore the parameter group. It

reads 1 if yes and 0 if no.

After the default values have been restored they will become active after the next rest or power cycle of

the TMCM-1617.

Object Description

Index Name Object Type Data Type

1011hRestore parameters Array UNSIGNED32

Table 27: Object Description (1011h)

Terms of delivery and rights to technical change reserved.

Download newest version at www.trinamic.com

TMCM-1617 CANopen®Firmware Manual •Firmware Version V1.06 | Document Revision V1.01 •2021-02-28 20 / 104

Entry Description

Sub-index Description Access PDO Mapping Value Range Default Value

00hHighest supported sub-index ro no UNSIGNED8 4

01hRestore all parameters rw no UNSIGNED32 —

02hRestore communication parameters rw no UNSIGNED32 —

04hRestore motor 0 parameters rw no UNSIGNED32 —

Table 28: Entry Description (1011h)

3.1.11 Object 1014h: COB-ID Emergency Object

This object deﬁnes the COB-ID of the emergency object (EMCY).

Object Description

Index Name Object Type Data Type

1014hCOB-ID emergency object Variable UNSIGNED32

Table 29: Object Description (1014h)

Entry Description

Sub-index Access PDO Mapping Value Range Default Value

0 rw no UNSIGNED32 80h+ Node ID

Table 30: Entry Description (1014h)

3.1.12 Object 1015h: Inhibit Time EMCY

The inhibit time for the EMCY message can be adjusted via this entry. The time has to be a multiple of

100µs.

Object Description

Index Name Object Type Data Type

1015hCOB-ID emergency object Variable UNSIGNED16

Table 31: Object Description (1015h)

Entry Description

Sub-index Access PDO Mapping Value Range Default Value

0 rw no UNSIGNED16 0

Table 32: Entry Description (1015h)

Terms of delivery and rights to technical change reserved.

Download newest version at www.trinamic.com

Page is loading ...

Trinamic TMCM-1617-CANopen Owner's manual

This manual is also suitable for

Trinamic TMCM-1617-CANopen Owner's manual

Related papers

Other documents