JANOME DC2010 Owner's manual

Page is loading ...

2

Names of Parts

q Mode selecting key

w Down (–) key

e Up (+) key

r LED display

t Spool holder (large)

y Spool pin

u Bobbin winding thread guide

i Thread guide

o Thread take-up lever

!0 Thread tension dial

!1 Face plate

!2 Thread cutter

!3 Automatic needle threader

!4 Needle plate

!5 Extension table (Accessory box)

!6 Hook cover

!7 Hook cover release button

!8 Stitch balance adjusting dial

!9 Reverse stitch button

@0 Auto-lock button

@1 Up/Down needle position button

@2 Speed control lever

@3 Needle clamp screw

@4 Needle

@5 Presser foot

@6 Foot holder

@7 Carrying handle

@8 Bobbin winding spindle

@9 Bobbin winder stopper

#0 Handwheel

#1 Power switch

#2 Machine socket

#3 Drop feed lever

#4 Free arm

#5 Buttonhole lever

#6 Presser foot lifter

#7 Hole for additional spool pin

q

w

e

r

t

y

u

i

o

!0

!1

!2

!3

!4

!5

!6

!7

!8

!9

@0

@1

@2

@3

@4

@5

@6

@7

@8

@9

#0

#1

#2 #3

#4

#5

#6

#7

NOTE:

The specifications are subject to change without prior notice.

SECTION 1. NAMES OF PARTS

Page is loading ...

4

Standard Accessories

Bobbin

Needle set

Satin stitch foot F

Zipper foot E

Automatic buttonhole foot R

Overedge foot C

Blind hem foot G

Seam ripper / Buttonhole opener

Screwdriver

Lint brush

Quilter bar

Foot control

Additional spool pin

Spool pin felt

Spool stand

Spool holder (large)

Spool holder (small)

Instruction book

Power supply cord

1

2

3

4

5

6

7

8

9

10

11

12

13

14

15

16

17

18

19

1

2

3

4

5

6

7

8

9

10

11

12

13

14 15

16 17

18

19

Page is loading ...

6

Extension Table and Free Arm Sewing

• To detach:

Pull the extension table to the left.

• To attach:

Slide the extension table along the free arm,

inserting the pin into the hole to attach.

q Extension table

w Pin

e Hole

q

e

w

• Free arm sewing:

The free arm sewing is useful for stitching sleeves,

waistbands, pant legs or any tubular garment, also

for darning socks or mending knees, elbows and

children’s wear.

Page is loading ...

10

Function Keys and Buttons

qq

q Reverse stitch button

While the reverse stitch button is pressed, the

machine sews backwards when the pattern 01, 02, 10

or 11 ( ) has been selected.

The machine will not sew backwards for any other

stitch pattern. Instead, the machine will immediately

lock the stitch and stop automatically.

ww

w Auto-lock button

The machine will lock the stitch and stop automatically

when the Auto-lock button is pressed while sewing the

pattern 01, 02, 10 or 11 ( ).

The machine willl sew to the end of pattern being

sewn and lock stitches to stop automatically when

other pattern has been selected.

ee

e Up/down needle position button

Press this button to bring the needle up or down.

If you start sewing with the needle up, it will be up

when you stop the machine.

If you start sewing with the needle down, it will be

down when you stop the machine.

NOTE:

You can sew a single unit of the selected pattern if

you press the Auto-lock button before starting to sew.

q

w

e

q

w

e

Page is loading ...

12

z Pattern selection mode:

Press the Up or Down key until the pattern

number of the desired stitch appears on the LED

display.

r Mode selection key

Press this button to enter one of the following modes.

r

z

x

c

c Stitch length adjusting mode:

Press the Up key to increase the stitch length or

Down key to decrease.

NOTE:

You can adjust the stitch length while the machine is

running.

x Stitch width adjusting mode:

Press the Up key to increase the stitch width or

Down key to decrease.

NOTE:

You can adjust the stitch width while the machine is

running.

Page is loading ...

14

Dropping the Feed Dog

The feed dog can be lowered by the drop feed lever

for sewing on buttons, manual embroidery etc.

Push the drop feed lever to the right to lower the feed

dog.

Push the lever to the left to raise the feed dog; it will

return to the up position when starting the machine.

NOTE:

The feed dog should be in up position for normal

sewing. Turn the handwheel toward you to check if

the feed dog comes up after setting the lever in the

up position.

q Down position

w Up position

e Feed dog

r Handwheel

q

w

e

r

w

e

q

w

e

Raising and Lowering the Presser Foot

The presser foot lifter raises and lowers the presser

foot.

You can raise it about 0.6 cm (1/4") higher than the

normal up position for easy removal of the presser

foot, or to help you to place thick fabric under the foot.

q Lowered position

w Normal up position

e Highest position

Page is loading ...

16

Changing Needles

WARNING:

Turn OFF the power switch before changing the

needle.

z Loosen the needle clamp screw and pull out the

needle.

x Insert a new needle into the needle clamp with the

flat side facing back.

Push the needle up against the stopper pin and

tighten the needle clamp screw firmly.

q Needle clamp screw

w Stopper pin

e Flat side

r Power switch

c To check the needle:

Place the flat side of the needle onto something flat

(needle plate, glass etc).

The clearance between the needle and the flat

surface should be consistent.

t Clearance

WARNING:

Never use a bent or blunt needle, which can cause it

to break.

q

w

e

r

z

x

t

c

Detaching and Attaching the Foot Holder

WARNING:

Turn OFF the power switch before detaching or

attaching the foot holder.

• To detach:

Raise the presser bar and turn the setscrew

counterclockwise to remove it.

Remove the foot holder.

q Setscrew

w Foot holder

• To attach:

Align the hole in the foot holder with the threaded

hole on the presser bar and insert the setscrew

through the hole. Tighten the setscrew by turning it

clockwise.

q

w

e

q

w

q

Changing the Presser Foot

WARNING:

Turn OFF the power switch before changing the foot.

Always use the proper foot for the selected pattern.

Wrong foot can cause needle to break.

• To release:

Raise the needle and presser foot.

Press the red button on the back of the foot holder

and the foot will drop off.

q Red button

• To snap on:

Place the presser foot so the pin on the foot lies just

under the groove of the foot holder.

Lower the foot holder to lock the foot in place.

w Groove

e Pin

Page is loading ...

18

*

Check your needles frequently for barbed or

blunted points. Snags and runs in knits, fine silks

and silk-like fabrics are permanent and are almost

always caused by a damaged needle.

•

Thread and Needle Chart

Light

weight

Medium

weight

Heavy

weight

Fabrics

Crepe de Chine,

Voile,

Lawn, Organdy,

Georgette,

Tricot

Linens, Cotton, Pique,

Serge, Double Knits,

Percale

Denim, Tweed,

Gabardine,

Coating, Drapery and

Upholstery Fabric

Threads

Fine Silk

Fine Cotton

Fine Synthetic

Fine Cotton

Covered

Polyester

50 silk

50 to 80 Cotton

50 to 60

Synthetic

Cotton Covered

Polyester

50 silk

40 to 50 Cotton

40 to 50

Synthetic

Cotton Covered

Polyester

Needle Size

9

or

11

or

14

or

16

*

In general, fine threads and needles are used for

sewing thin fabrics, and thicker threads and

needles are used for sewing heavy fabrics.

Always test thread and needle size on a small piece

of fabric which will be used for actual sewing.

*

Use the same thread for needle and bobbin.

*

When sewing stretch, very fine fabrics and

synthetics, use a stretch needle.

The stretch needle effectively prevents

skipped stitches.

*

When sewing very fine fabrics, sew over a piece

of paper to prevent distortion.

Page is loading ...

20

Winding the Bobbin

Removing the bobbin

Slide the hook cover release button to the right, and

remove the hook cover.

Lift the bobbin out.

q Hook cover release button

w Hook cover

e Bobbin

Setting the spool of thread

Place the spool of thread on the spool pin with the

thread coming off the spool as shown.

• For an ordinary spool:

Use the large spool holder.

q Large spool holder

• For a narrow or small spool:

Use the small spool holder.

w Small spool holder

• Additional spool pin

The additional spool pin is for bobbin winding, without

unthreading the machine, and for twin needle sewing.

Set the spool stand under the additional spool pin,

place the felt, then insert into the hole.

q Spool

w Additional spool pin

e Felt

r Spool stand

t Hole for the additional spool pin

Winding the bobbin

NOTE:

Set the speed control lever at for bobbin winding.

z Guide the thread around the bobbin winder thread

guide.

q Bobbin winder thread guide

x Insert the thread through the hole on the bobbin,

threading from the inside to the outside. Put the

bobbin on the bobbin winder spindle.

w Bobbin winder spindle

c Push the bobbin winder spindle to the right. The

LED display shows .

v With the free end of the thread held in your hand,

depress the foot control. Stop the machine when

the bobbin has made a few turns, and cut the

thread close to the hole on the bobbin.

b Depress the foot control again. When the bobbin is

fully wound, it will stop automatically. Return the

bobbin to its original position by moving the spindle

to the left, and cut the thread as shown.

q

w

e

q

w

q

w

e

r

t

z

x

xc

vb

q

w

Page is loading ...

22

Inserting the bobbin

z Place the bobbin in the bobbin holder with the

thread running counter-clockwise.

q End of the thread

w Bobbin holder

q

w

e

t

r

t

y

u

z

x

c

v

b

b Pull out about 10 cm (4") of thread and attach the

hook cover.

y Bobbin thread

u Align left edge of the hook cover.

v Draw the thread to the back.

The bobbin should turn counterclockwise when

pulling the thread.

c Continue to draw the thread lightly through the

tension blades until it slips into slot B.

r Tension blades

t Slot B

x Guide the thread into slot A on the front side of the

bobbin holder. Draw the thread to the left

sliding it between the tension spring blades.

e Slot A

Page is loading ...

24

3

Threading the Machine

Threading the machine

q Spool

w Spool holder

e Presser foot lifter

qw

z

c

e

x

v

b

u

y

i

o

!0

z

r

t

x

c

v bv Pass the thread in the lower thread guide from the

right.

o Lower thread guide

b Slip the thread in the needle bar thread guide on

the left.

!0 Needle bar thread guide

NOTE:

Refer to page 26 for the automatic needle threader.

c Firmly draw the thread up to the take-up lever,

and down into the eye of the thread take-up lever

from the right to left.

i Thread take-up lever

x Draw the end of the thread down around the thread

guide plate and draw it up to the left.

Make sure the thread slips in between the tension

disks.

y Thread guide plate

u Tension disks

z Raise the presser foot.

Press the Up/Down needle position button to

bring the take-up lever to its highest position.

Turn the power switch OFF.

Draw the end of the thread with your left hand and

hook around the upper thread guide while holding

the thread at the spool with your right hand. Pass

the thread down into the slot.

r Upper thread guide

t Slot

Page is loading ...

26

Automatic Needle Threader

z Raise the needle to its highest position.

Pull down the needle threader knob as far as it will go.

q Needle threader knob

w Hook

x Turn the knob in the direction of the arrow as

shown. Insert hook into the needle eye.

Lead the thread around guide and under the hook.

e Threader guide

c Turn the knob in the direction of the arrow in the

illustration, drawing the thread loop through the

needle.

v Pull the thread through the needle eye.

NOTE:

The needle threader can be used with a #11 to #16.

Thread size 50 to 90 should also work well.

Drawing Up Bobbin Thread

z Raise the presser foot and hold the needle thread

with your fingers.

q Needle thread

x Press the Up/down needle position button to

raise the needle to its highest position. Pull the

needle thread to pick up a loop of the bobbin

thread.

q Needle thread

w Bobbin thread

e Up/down needle position button

c Draw 10 cm (4") of both threads to the back under

the presser foot.

q

w

e

w

z

x

c v

w

q

e

q

w

z

x

c

q

Page is loading ...

28

Balancing Thread Tension

Correct tension

q Needle thread (Top thread)

w Bobbin thread (Bottom thread)

e To loosen

r To tighten

The ideal straight stitch has threads locked between

two layers of fabric, as illustrated.

If you look at the top and bottom of a seam, notice

that there are no gaps. Each stitch is smooth and even.

When adjusting the needle thread tension, the higher

the number, the tighter the needle thread tension.

Results depend on:

- stiffness and thickness of the fabric

- number of fabric layers

- type of stitch

Tension is too tight

q Needle thread (Top thread)

w Bobbin thread (Bottom thread)

e To loosen

r Right side (Top side) of fabric

t Wrong side (Bottom side) of fabric

If the bobbin thread shows through on the right side

(Top side) of the fabric, and the stitch feels bumpy,

turn the dial to a lower tension setting number to

loosen the needle thread tension.

Tension is too loose

q Needle thread (Top thread)

w Bobbin thread (Bottom thread)

e To tighten

r Right side (Top side) of fabric

t Wrong side (Bottom side) of fabric

If the needle thread shows through on the wrong side

(Bottom side) of the fabric, and the stitch feels

bumpy, turn the dial to a higher tension setting

number to tighten the needle thread tension.

4

q

w

e

r

t

Adjusting the needle thread tension for a zigzag stitch

For an ideal zigzag stitch, the bobbin thread does not

show on the right side (Top side) of the fabric and

needle thread shows slightly on the wrong side

(Bottom side) of the fabric.

See the illustrations for correct appearance.

To match this appearance, adjust the needle tension.

Correct tension

q Right side (Top side) of fabric

w Wrong side (Bottom side) of fabric

Minimize the amount of needle thread visible on the

wrong side (Bottom side) of the fabric without causing

excessive puckering, or causing the bobbin thread to

show on the right side (Top side) of the fabric.

Results vary with fabric, thread and sewing conditions.

Tension is too tight

q Right side (Top side) of fabric

w Wrong side (Bottom side) of fabric

The corner of each zigzag pulls together on the right

side of the fabric.

q

w

q

w

q

w

Tension is too loose

q Right side (Top side) of fabric

w Wrong side (Bottom side) of fabric

The corner of each zigzag point pulls together on the

wrong side of the fabric.

q

w

e

r

q

w

e

r

Page is loading ...

30

SECTION 3. BASIC SEWING

Straight Stitch Sewing

Machine setting

q Pattern:

w LED display

e Foot: A: Zigzag foot

Starting to sew

Raise the presser foot and place the fabric on the

machine.

Lower the needle into the fabric where you want to

start.

Lower the presser foot and start sewing.

NOTE:

To fasten the beginning of the seams, sew several

reverse stitches by pressing the reverse stitch

button, or use pattern #03 (Lock-a-Matic stitch ).

qw e

q

w

e

Fastening the seam

z Sew several stitches in reverse by pressing the

reverse stitch button w to fasten the end of seam.

w Reverse stitch button

NOTE:

If you use pattern #03 (Lock-a-Matic stitch ),

press the reverse stitch w button once and the

machine will sew in reverse and stop automatically.

x Raise the presser foot and pull the fabric to the

rear.

c Draw the threads up and into the thread cutter. The

threads are cut at the proper length for starting the

next seam.

e Thread cutter

Changing sewing direction

Stop the machine and bring the needle down into the

fabrics by pressing the Up/down needle position

button q.

Raise the presser foot.

Pivot the fabric around the needle to change the

sewing direction as desired.

Lower the presser foot and start sewing in a new

direction.

q Up/down needle position button

z

x

c

Page is loading ...

32

Adjusting the Stitch Length

Press the mode selection key to enter stitch

length adjusting mode.

The LED display shows “2.2” (default setting).

Press the Down (–) key to decrease stitch length.

Press the Up (+) key to increase stitch length.

The stitch length can be varied from 0.0 to 5.0.

NOTE:

The machine will not sew reverse stitches longer

than approximately 2.5 mm.

qwe

1.0

2.2 5.0

0.0

3.5 7.0

Changing the Needle Drop Position

You can change the needle drop position of straight

stitching for patterns #01–04 and #18–21

( ).

Press the mode selection key to enter stitch

width adjusting mode.

The LED display shows “3.5” (default setting), which

represents the center needle position.

Press the Down (–) key to move the needle to the left.

Press the Up (+) key to move the needle to the right

q Left needle position

w Center needle position

e Right needle position

Page is loading ...

34

Using the Seam Guides

The seam guides on the needle plate are engraved to

help you measure seam allowance. The numbers on

the needle plate indicate the distance between the

center needle position and the edge of the fabric. The

lines are 1/8˝ (0.3 cm) apart, and engraved at 3/8˝,

4/8˝, 5/8˝ and 6/8˝. The lines in millimeters are 5 mm

apart, and are engraved at 10 mm, 15 mm and 20 mm.

q Seam guides

w Needle drop position

e Seam allowance

q

e

w

q

Sewing from the Edge of Thick Fabric

The black button locks the zigzag foot to avoid

slipping when sewing from the extreme edge or

sewing across the hem.

z Lower the needle into the fabric at the point to start

sewing.

x Lower the foot while pushing the black button in.

The foot is locked in the horizontal position.

c The foot will be unlocked automatically after

sewing several stitches.

q Black button

Turning Square Corners

To maintain a 5/8” seam allowance after turning a

square corner, use the cornering guide lines on the

needle plate.

z Stop stitching when the front edge of the fabric

reaches the cornering guide lines.

q Cornering guide lines

x Press the Up/Down needle position button to lower

the needle into the fabric.

w Up/Down needle position button

c Raise the presser foot and turn the fabric

counterclock-wise 90º.

e Presser foot

v Lower the presser foot and begin stitching in the

new direction.

w

q

e

Page is loading ...

36

Variety of Straight Stitching

q

w

q

w

q

w

qw

q Pattern: Saddle stitch

w Foot A: Zigzag foot

Long straight stretch stitch, similar to hand stitches

q Pattern: Stretch stitch

w Foot F: Satin stitch foot

For top stitching and quilting

q Pattern: Sculpture stitch

w Foot F: Satin stitch foot

For top stitching and outlining designs

Sew slowly at the corners.

q Pattern: Straight stretch stitch

w Foot A: Zigzag foot

Strong and durable stitch recommended for stretch

fabrics and areas to reinforce

q Pattern: Stretch stitch

w Foot A: Zigzag foot

For seaming stretch fabrics that tend to pucker

The seam can be opened flat.

q Pattern: Locking stitch

w Foot A: Zigzag foot

Seaming with auto locking stitches at the beginning.

Press the reverse stitch button once at the end; the

machine will lock the stitches and stop

automatically.

q Pattern: Lock-A-Matic stitch

w Foot A: Zigzag foot

Seaming with auto reverse stitches at the beginning.

Press the reverse stitch button once at the end; the

machine will sew the reverse stitches and stop

automatically.

q Pattern: Straight stitch

w Foot A: Zigzag foot

For seaming garments, zipper application and

more.

Pattern #02 is used for seaming along the edge.

Page is loading ...

38

Basic Zigzag Stitch

Machine setting

q Pattern

w LED display

e Foot A: Zigzag foot

qw e

q

w

z

x

Adjusting the Stitch Width

z Press the mode selection key to enter stitch

width adjusting mode.

The LED display shows the default setting of the

selected pattern.

Press the Down (–) key to decrease stitch width.

Press the Up (+) key to increase stitch width.

q Stitch width

Zigzag stitch is one of the most useful and versatile

stitches.

It is used for overcasting, mending, appliqué also

used as a decorative stitch.

NOTE:

Use an interface when sewing on stretch fabric

such as knit, jersey or tricot.

Adjusting the Stitch Length

x Press the mode selection key to enter stitch

length adjusting mode.

The LED display shows the default setting of the

selected pattern.

Press the Down (–) key to decrease stitch length.

Press the Up (+) key to increase stitch length.

w Stitch length

Page is loading ...

40

Overcasting (Zigzag stitch)

Machine setting

q Pattern

w LED display

e Foot A:Zigzag foot or

C:Overedge foot

qw e

q

qwe

q

This stitch overcasts and seams the raw edge at the

same time, it prevents the fabric from fraying.

q Guide

Overedge Stitch

Machine setting

q Pattern

w LED display

e Foot C: Overedge foot

Multiple Zigzag Stitch (Tricot stitch)

Machine setting

q Pattern

w LED display

e Foot A: Zigzag foot

This stitch is used to finish a raw edge of synthetics

and other stretch fabrics that tend to pucker. Sew

along the fabric edge leaving enough seam

allowance.

After sewing, trim off the seam allowance closer to the

stitches as shown.

CAUTION:

Do not set the stitch width less than 5 when using

the overedge foot to prevent the needle from

hitting the wires on the foot.

Place the raw edge of the fabric next to the guide of

the foot and start sewing.

q Guide

CAUTION:

Do not set the stitch width less than 5 when using

the overedge foot to prevent the needle from

hitting the wires on the foot.

SECTION 4. UTILITY STITCHES

Page is loading ...

42

Serging Stitch

Machine setting

q Pattern

w LED display

e Foot C: Overedge foot

qw e

CAUTION:

Do not set the stitch width less than 5 when using

the overedge foot to prevent the needle from

hitting the wires on the foot.

This stitch is used for finishing the raw edges of

stretch fabrics that tend to unravel.

qw e

This stitch is recommended for finishing the edge of

knit fabrics.

Sew along the fabric edge leaving an extra allowance.

After you finished sewing, trim allowance close to the

stitches.

Knit Stitch

Machine setting

q Pattern

w LED display

e Foot A: Zigzag foot

Page is loading ...

JANOME DC2010 Owner's manual

This manual is also suitable for

JANOME DC2010 Owner's manual

in other languages

Related papers

Other documents