Eco Flo EFSWJ10P Owner's manual

Owner’s Manual

Plastic Shallow

Jet Pumps

General Safety . . . . . . . . . . . . . . . . . . . . 2

Installation . . . . . . . . . . . . . . . . . . . . . 3-5

Electrical . . . . . . . . . . . . . . . . . . . . . . . . .6

Operation . . . . . . . . . . . . . . . . . . . . . . . . 7

Troubleshooting . . . . . . . . . . . . . . . . . . . 8

Repair Parts . . . . . . . . . . . . . . . . . . . . . . 9

Jet/Tank Assembly . . . . . . . . . . . . . . . . 10

Warranty . . . . . . . . . . . . . . . . . . . . . . . . 11

TABLE OF CONTENTS

Safety: Need safety Info

1. Avoid Pressure Burns/Explosion

2. Avoid Electric Shock

Fill Pump with water: Ensure pump body is lled with water to discharge.

Motor’s Electrical Settings: Set motor to proper voltage,

i.e. voltage supplied to pump – See electrical section

Need Help: Call 1-877-326-3561 for assistance

Important Safety Instructions Safety Labels

Carefully read and follow all safety

instructions in this manual and on pump.

SAVE THESE INSTRUCTIONS – This manual

contains important instructions that should be

followed during installation, operation, and main-

tenance of the product. Save this manual for

future reference.

This is the safety alert symbol. When you

see this symbol on your pump or in this manual,

look for one of the following signal words and be

alert to the potential for personal injury!

Indicates a hazard which, if

not avoided, will result in death or serious injury.

Indicates a hazard which,

if not avoided, could result in death or serious

injury.

Indicates a hazard which, if

not avoided, could result in minor or moderate

injury.

NOTICE indicates practices not related to

personal injury.

Keep safety labels in good condition. Replace

missing or damaged safety labels.

General Safety

Risk of burns. Do not

touch an operating motor. Motors are de-

signed to operate at high temperatures. To

avoid burns when servicing pump, allow it to

cool for 20 minutes after shut-down before

handling.

Do not allow pump or any system compo-

nent to freeze. To do so will void warranty.

Pump water only with this pump.

Periodically inspect pump and system com-

ponents.

Wear safety glasses at all times when work-

ing on pumps.

Risk of explosion. Pump

body may explode if used as a booster

pump.

GENERAL SAFETY

STOP

Before you start

For parts or assistance, call ECO-FLO Customer Service at 1-877 326-3561

2

DEDICATED SHALLOW WELL PUMP INSTALLATIONS

REPLACING AN OLD PUMP

For parts or assistance, call ECO-FLO Customer Service at 1-877 326-3561

Disconnect power to pump before

working on pump or motor.

1. Drain and remove the old pump. Check the old pipe for

scale, lime, rust, etc., and replace it if necessary.

2. Install the pump in the system. Make sure that all pipe

joints in the suction pipe are air-tight as well as water

tight. If the suction pipe can suck air, the pump will not

be able to pull water from the well.

3. Adjust the pump mounting height so that the plumbing

connections do not put a strain on the pump body.

Support the pipe so that the pump body does not take

the weight of piping or ttings.

!

(Figure 1)

Foot Valve

Stainer

Well Casing

Sanitary Well Seal

To Power Box

Suction Pipe

Priming Tee with

Priming Port, Plug

and Pressure

Gauge

To House

Water

System

2 3

Cased Well Installation (Figure 1)

1. Mount the pump as close to the well as possible.

2. Assemble the foot valve, strainer, and well pipe.

Make sure that the foot valve works freely.

3. Lower the pipe into the well until the strainer is ve

feet above the bottom of the well. It should also be at

least 10 feet below the well’s water level.

4. Install a sanitary well seal.

5. Install a priming tee, priming plug, and pressure gauge

to pump’s discharge port. Connect the pipe from the

well to the pump’s suction port, using the fewest

possible ttings-especially elbows – increase friction

in the pipe. The suction pipe should be at least

as large as the suction port on the pump. Support

the pipe so that there are no dips or sags in the pipe,

so not to strain the pump body, and so that it

slopes slightly upward from the well to the pump

(Note: Not doing so can create air locks preventing

the pump from working properly). Seal the suction

pipe joints with PTFE pipe thread sealant tape or a

PTFE-based pipe joint compound. Joints must be air-

and-water-tight. If the suction pipe can suck air,

the pump cannot pull water from well.

6. See instructions on page 8 for connecting discharge

pipe to tank.

DEDICATED SHALLOW WELL PUMP INSTALLATIONS

For parts or assistance, call ECO-FLO Customer Service at 1-877 326-3561

Driven Point Installation (Figure 2)

1. Drive the well point, using “drive couplings” and a “drivecap”.

“Drive ttings” are threaded all the way through and allow the

pipe ends to butt against each other so that the driving

force of the maul is carried by the pipe and not by the threads.

The ordinary ttings found in hardware stores are not threaded

all the way through the tting and can collapse under impact.

“Drive ttings” are also smoother than standard plumbing

ttings, making ground penetration easier.

2 . Mount the pump as close to the well as possible.

3. Use the fewest possible ttings (especially elbows) when

connecting the pipe from the well point to the pump suction

port. The suction pipe should be at least as large as the suction

port on the pump.

4. Install a check valve if your pump is not equipped with one.

5. Install a priming tee, priming plug, and pressure gauge

to pump’s discharge port. Connect the pipe from the

well to the pump’s suction port, using the fewest

possible ttings-especially elbows – increase friction

in the pipe. The suction pipe should be at least

as large as the suction port on the pump. Support

the pipe so that there are no dips or sags in the pipe,

so not to strain the pump body, and so that it

slopes slightly upward from the well to the pump

(Note: Not doing so can create air locks preventing

the pump from working properly). Seal the suction

pipe joints with PTFE pipe thread sealant tape or a

PTFE-based pipe joint compound. Joints must be air-

and-water-tight. If the suction pipe can suck air,

the pump cannot pull water from well.

6. If one well point does not supply enough water,

consider connecting two or three well points to one

suction pipe.

7. See instructions on page 8 for connecting discharge

pipe to tank.

(Figure 2)

Drive Point

Drive

Coupling

Check Valve

To Power Box

Suction Pipe

Priming Tee with

Priming Port,

Plug and Pressure

Gauge

To House

Water

System

4

DEDICATED SHALLOW WELL PUMP INSTALLATIONS

For parts or assistance, call ECO-FLO Customer Service at 1-877 326-3561

Surface Water Installation (Figure 3)

Possible contamination. Do not use

surface water for drinking. The installation

shown could be used for sprinkler applications.

1. The pump should be installed as close to the water

as possible, with the fewest possible ttings (especially

elbows) in the suction pipe. The suction pipe should

be at least as large as the suction port on the pump.

2. Assemble a foot valve and strainer to the suction pipe.

Make sure that the foot valve works freely. Use PTFE

pipe thread sealant tape or a PTFE-based pipe joint

compound on threaded pipe joints.

3. Install a screen to protect the water system from letting

debris enter the system.

4. Lower the pipe into the water until the strainer is ve

feet above the bottom. It should also be at least 10

feet below the water level in order to prevent the pump

from sucking air.

5. Install a priming tee, priming plug, and pressure gauge

to pump’s discharge port. Connect the pipe from the

well to the pump’s suction port, using the fewest

possible ttings-especially elbows – increase friction

in the pipe. The suction pipe should be at least

as large as the suction port on the pump. Support

the pipe so that there are no dips or sags in the pipe,

so not to strain the pump body, and so that it

slopes slightly upward from the well to the pump

(Note: Not doing so can create air locks preventing

the pump from working properly). Seal the suction

pipe joints with PTFE pipe thread sealant tape or a

PTFE-based pipe joint compound. Joints must be air-

and-water-tight. If the suction pipe can suck air,

the pump cannot pull water from well.

6. Joints must be air-and water-tight. If the suction pipe

can suck air, the pump cannot pull water from the

water source.

7. See instructions on page 8 for connecting discharge

pipe to tank.

!

(Figure 3)

Foot Valve

Screen

Water Surface

To Power Box

Suction Pipe

Priming Tee with

Priming Port, Plug

and Pressure

Gauge

To House

Water

System

4 5

For parts or assistance, call ECO-FLO Customer Service at 1-877 326-3561

6

BRANCH

AWG

DISTANCE IN FEET FROM MOTOR TO SUPPLY

MAX. LOAD

FUSE

MIN. WIRE

0-100 101-200 201-300 301-400 401-500

MOTOR HP VOLTS AMP RATING AMP SIZE (mm

2

) AWG WIRE SIZE (mm

2

)

1/2 115/230 10.6/6.5 15/15 12/14 (3/2) 12/14 (8.4/2) 8/14 (2/2) 6/14 (14/2) 6/12 (14/3) 4/10 (21/5.5)

3/4 115/230 11/6.6 20/15 10/14 (5.5/2) 12/14 (8.4/2) 8/14 (8.4/2) 6/12 (14/3) 4/10 (21/5.5) 4/10 (21/5.5)

1 115/230 11.8/6.7 25/15 10/14 (5.5/2) 6/14 (14/2) 8/14 (8.4/2) 6/12 (14/3) 4/10 (21/5.5) 4/10 (21/5.5)

ELECTRICAL

Motor Switch Settings (Figure 8)

Motors are designed to run on either 115 volt or 230 volt

current. Be sure the motor’s wires are attached properly to

the motor’s control panel for the voltage required.

Wiring Pressure Switch

Attach the wires from the power source to the pressure

switch following the directions provided under the cover of

the pressure switch, i.e. remove the pressure switch cover

and follow wiring directions under the cover lid. Be sure to

ground wire the pressure switch to the motor.

Wiring the Motor (Figure 9)

Attach wires between the pressure switch and the motor

ensuring the wires are connected to the motor for the proper

electrical source voltage, i.e. 115V or 230V- see the wiring

diagrams in this manual or under the cover of the motor.

Ensure to ground the pressure switch

to the motor.

Disconnect power before working on

pump, motor, pressure switch or wiring

Motor may be hot. Allow to cool 20

minutes.

Water pressure may have built up in

the pump, pipes and/or tank. Drain

water to relieve pressure.

!

Wiring

Risk of electric shock.

Can shock, burn or kill.

1. To avoid dangerous or fatal electrical shock, turn OFF

power to motor before working on electrical

connections.

2. Ground motor before connecting to electrical power

supply. Failure to ground motor can cause severe or

fatal electrical shock hazard.

3. Supply voltage must be within +/- 10% of nameplate

voltage. Incorrect voltage can cause re or damage

motor and voids warranty. If in doubt consult a

licensed electrician.

4. Use wire size specied in Wiring Chart (below). If

possible, connect pump to a separate branch circuit

with no other appliances on it.

5. Do not ground to a gas supply line.

6. Wire motor according to diagram on motor nameplate.

If nameplate diagram diers from diagrams above,

follow nameplate diagram.

7. If this procedure or the wiring diagrams are

confusing, consult a licensed electrician.

Wiring Chart Recommended Wire and Fuse Sizes for 115 and 230 volts

(Figure 9)

Remove Motor

End Plate

Figure 8

For parts or assistance, call ECO-FLO Customer Service at 1-877 326-3561

6 7

Hazardous Pressure,

Install pressure relief valve in discharge pipe.

Release all pressure on system before working on any component.

OPERATION

remove the ll plugs, and rell the pump and piping.

You may have to repeat this two or three times in order

to get all the trapped air out of the piping.

6. When water pressure has built up and is maintained

by the pump, slowly close the pressure regulator control

valve while watching the pressure gauge needle.

Continue closing the valve until you see the pressure

gauge needle start to utter. If the needle starts to

utter, slowly open the valve just enough to stop the

utter. Your pump is now operating at peak eciency.

7. Close all open faucets. After the pump has built up

pressure in the system and shut o, check the

pressure switch operation by opening a faucet or two

and running enough water out to bleed o pressure

until the pump starts. If your jet has a 30/50 pressure

switch, the pump should start when the pressure

drops to 30 PSI and stop when pressure reaches 50

PSI. Run the pump through one or two complete cycles

to verify correct operation. This will also help clean the

system of dirt and scale dislodged during installation.

Risk of burns. Never run pump dry. Run-

ning pump without water may cause pump to overheat,

damaging seal and possibly causing burns to persons

handling pump. Fill pump with water before starting.

Be sure the pump is full of water before

starting the motor.

Risk of explosion and scalding. Never run

pump against closed discharge. To do so can boil water

inside pump, causing hazardous pressure in unit, risk of

explosion and possible scalding persons handling pump.

1. Open the control valve as far as possible. Then remove

the priming plug from the pump and ll the pump, ll

all piping between the pump and the well, and make

sure that all piping in the well is full. If you have also

installed a priming tee in the suction piping, remove

the plug from the tee and ll the suction piping.

2. Replace all ll plugs. Leave the control valve open (in

a shallow well installation, the control valve always

stays open).

3. Turn electric power on!

4. Start the pump. The pump should pump water in two

or three minutes.

5. If you don’t have water after 2 or 3 minutes, stop the

pump and remove the ll plugs. Rell the pump and

piping. You may have to repeat this two or three times

in order to get all the trapped air out of the piping. The

control valve remains open throughout this procedure.

6. After the pump has built up pressure in the system and

shut o, check the pressure switch operation by

opening a faucet or two and running enough water out

to bleed o pressure until the pump starts. If your jet

has a 30/50 pressure switch, the pump should start

when the pressure drops to 30 PSI and stop when pres-

sure reaches 50 PSI. Run the pump through one or two

complete cycles to verify correct operation. This will

also help clean the system of dirt and scale dislodged

during installation.

PREPARING TO START THE PUMP - SHALLOW WELL

PREPARING TO START THE PUMP - DEEP WELL

Risk of burns. Never run pump dry.

Running pump without water may cause pump to overheat,

damaging seal and possibly causing burns to persons

handling pump. Fill pump with water before starting.

Be sure the pump is full of water before

starting the motor.

Risk of explosion and scalding. Never

run pump against closed discharge. To do so can boil water

inside pump, causing hazardous pressure in unit, risk of

explosion and possibly scalding persons handling pump.

1. Open the pressure regulator control valve as far as

possible. Then remove the priming plug from the pump

and ll the pump, ll all piping between the pump and the

well, and make sure that all piping in the well is full.

If you have also installed a priming tee in the suction

piping, remove the plug from the tee and ll the suction

piping.

2. Replace all plugs.

3. Power on!

4. Start the pump and watch the pressure gauge. The

pressure should build rapidly to 50 PSI as the pump

primes.

5. Open several faucets in the residence to permit water

ow and to release trapped air. After 2 or 3 minutes, the

gauge should show pressure. If not, stop the pump,

!

For parts or assistance, call ECO-FLO Customer Service at 1-877 326-3561

8

CORRECTIVE ACTION

Replace fuse or reset circuit breaker.

DISCONNECT POWER; Replace starting switch

Refer to instructions on wiring (Page 9). DISCONNECT POWER; check and

tighten all wiring. (WARNING symbol) Hazardous voltage. Capacitor voltage may

be hazardous. To discharge capacitor, hold insulated handle screwdriver BY THE

HANDLE and short capacitor terminals together. Do not touch metal screwdriver

blade or capacitor terminals. If in doubt, consult a qualiﬁed electrician.

Refer to instructions on wiring.

Check with power company. Install heavier wiring if wire size is too small (See

Electrical/Wiring Chart)

See section below on too frequent cycling.

In new installation:

1. Re-prime according to instructions.

2. Check all connections on suction line and AVC with shaving cream.

3. Replace foot valve or check valve.

In installation already in use:

1. Check all connections on suction line and shaft seal.

2. Lower suction line into water and re-prime. If receding water level in

well exceeds 25’ (7.6M0, a deep well pump is needed.

3. Replace faulty valve.

Clean foot valve or strainer

Clean ejector or impeller.

Replace check valve or foot valve.

Thaw pipes. Bury pipes below frost line. Heat pit or pump house.

Raise foot valve and/or strainer above bottom of water source. Clean foot valve

and strainer.

A deep well jet will be needed if your well is more than 25’ (7.6M0 depth to

water.

A new nozzle and venturi combination may be needed.

Replace with plastic pipe where possible, otherwise with new steel pipe.

Use larger piping.

DISCONNECT POWER; adjust or replace pressure switch

Close faucets

Clean venturi, nozzle or impeller

Drain tank to air volume control port. Check AVC for defects. Check all

connections for leaks.

Check connections.

Replace foot valve.

Adjust or replace pressure switch.

DISCONNECT POWER and open faucets until all pressure is relieved. Using tire

pressure gauge, check air pressure in tank at valve stem located on the tank.

If less than pressure switch cut in setting (30-50 PSI), pump air into tank from

outside source until air pressure is 2 PSI less than cut-in setting of switch.

Check air valve for leaks (use soapy solution) and replace core if necessary.

When pump has picked up prime, it should pump solid water with no air.

Suction pipe is sucking air. Check joints for leaks with shaving cream.

Consult factory about installing a sleeve in the well.

Lower foot valve if possible, otherwise restrict pump discharge.

TROUBLE SHOOTING

POSSIBLE CAUSE(S)

Fuse is blown or circuit breaker tripped

Starting switch is defective

Wires at motor are loose, disconnected, or wired

incorrectly

Motor is wired incorrectly

Voltage is too low

Pump cycles too frequently

Pump in new installa tion did not prime due to:

1. Pipes were not ﬁlled with water

2. Air leaks

3. Leaking foot valve or check valve

Pump has lost prime through:

1. Air leaks

2. Water level below suction pipe inlet

3. Faulty check or foot valve.

Foot valve or strainer is plugged

Ejector or impeller is plugged

Check valve or foot valve is stuck shut

Pipes are frozen

Foot valve and/or strainer are buried in sand or mud

Water level is too low for shallow well setup to

deliver water

Water level in well is lower than estimated.

Steel piping (if used) is corroded or limed, causing

excess friction

Piping is too small in size

Pressure switch is out of adjustment or contacts

are welded together

Faucets have been left open

Venturi, nozzle or impeller is clogged

Standard pressure tank is waterlogged and has no

air cushion

Pipes leak

Foot valve leaks

Pressure switch is out of adjustment

Air charge too low in pre-charged tank

Pump is not primed

Leak in suction side of pump

Well is gaseous

Intermittent over-pumping of well. (Water drawn

down below foot valve.)

SYSTEM

Motor will not run

Motor runs hot and

overload kicks off

Motor runs but no

water is delivered*

*Stop pump; then check

prime before looking for

other causes. Unscrew

priming plug and see if

water is in priming hole

Pump does not deliver

water to full capacity

(Also check point 3 im-

mediately above)

Pump delivers water but

does not shut off or pump

cycles too frequently

Air spurts from faucets

For parts or assistance, call ECO-FLO Customer Service at 1-877 326-3561

9

SHALLOW WELL PUMP REPAIR PARTS

1

18

234567891011121314

171615

NO. QUANTITY PART NUMBER DESCRIPTION

1 3 EFSWJ5P01 Plug

2 1 EFSWJ5P02 Volute

3 1 EFSWJ5P03 Adapter/Pressure Switch

4 1 EFSWJ5P04 O-Ring

1 EFSWJ5P05 Diffuser for 1/2 HP

5 1 EFSWJ7P05 Diffuser for 3/4 HP

1 EFSWJ7P05 Diffuser for 1 HP

1 EFSWJ5P06 Impeller for 1/2 HP

6 1 EFSWJ7P06 Impeller for 3/4 HP

1 EFSWJ7P06 Impeller for 1 HP

7 1 EFSWJ5P07 Seal

8 1 EFSWJ5P08 O-Ring

9 1 EFSWJ5P09 Seal Plate

10 1 EFSWJ5P10 Base

11 1 EFSWJ5P11 Pressure Tube

12 1 EFSWJ5P12 Adaptor

13 1 EFSWJ5P13 Pressure Switch

14 1 EFSWJ5P14 Nut

15 4 EFSWJ5P15 Screw

16 4 EFSWJ5P16 Washer

1 EFSWJ5P17 Motor for 1/2 HP

17 1 EFSWJ7P17 Motor for 3/4 HP

1 EFSWJ1P17 Motor for 1 HP

18 1 EFSWJ5P18 Plate

10

For parts or assistance, call ECO-FLO Customer Service at 1-877 326-3561

JET/TANK PUMP ASSEMBLY

Tank

1. Remove tank from its carton.

2. Using a tire pressure gauge, check the air in the tank.

It may need to be adjusted once you know the on/o settings on the pump’s pressure switch

(see number 3 below).

Pump

1. Remove the pump from its carton.

2. Retain the pump’s owners manual.

3. Remove the cover from the pump’s pressure switch, and read the on/o settings from the underside of the

pressure switch cover. Typically readings are:

a. Pump (motor) on pressure: 30 PSI (pounds per square inch);

b. Pump (motor) o pressure: 50 PSI.

4. Once you know the turn on/o pressures, alter the air pressure in the empty pre-charge tank to 2 (two) PSI below

the “on” pressure, i.e. to 28 PSI.

5. It is critical the pressure in the tank be 2 PSI below the “tank turn” on pressure

Mounting Kit

1. Remove the kit’s contents and sort them into groups.

Jet Tank Assembly

1. Mount the jet on to the tank securing the jet with the 4 bolts, washers, and nuts provided in the kit.

2. Ensure the input end of the pump is on the same end of the tank input end.

3. Snug the nuts on the bolts while you install other pieces of the kit.

4. Use Teon tape or other plumbing sealant to ensure all connections are sealed.

11

For parts or assistance, call ECO-FLO Customer Service at 1-877 326-3561

1899 Cottage Street, Ashland, Ohio 44805

Telephone: 1-877-326-3561

Fax: 1-877-326-1994

www.ecooproducts.com

Retain Original Purchase Receipt for Warranty Eligibility

Limited Warranty

Manufacturer warrants to the original consumer purchaser (“Purchaser” or “You”) that its products are free from defects in

material and workmanship for a period of twelve (12) months from the date of the original consumer purchase. If, within

twelve (12) months from the original consumer purchase, any such product shall prove to be defective, it shall be repaired

or replaced at manufacturer’s option, subject to the terms and conditions set forth herein. Note that this limited warranty

applies to manufacturing defects only and not to ordinary wear and tear. All mechanical devices need periodic parts and

service to perform well. This limited warranty does not cover repair when normal use has exhausted the life of a part or

the equipment.

The original purchase receipt and product warranty information label are required to determine warranty eligibility. Eligibil-

ity is based on purchase date or original product – not the date of replacement under warranty. The warranty is limited to

repair or replacement of original purchased product only, not replacement product (i.e. one warranty replacement allowed

per purchase).

Purchaser pays all removal, installation, labor, shipping, and incidental charges.

Claims made under this warranty shall be made by contacting and returning the product to the factory immediately after

the discovery or any alleged defect. Manufacturer will subsequently take corrective action as promptly as reasonably pos-

sible. No requests for service will be accepted if received more than 30 days after the warranty expires. Warranty is not

transferable and does not apply to products used in commercial/rental applications.

General Terms and Conditions; Limitations of Remedies

You must pay all labor and shipping charges necessary to replace product covered by this warranty. This warranty does

not apply to the following: (1) acts of God; (2) products which, in manufacturer’s sole judgment, have been subject to

negligence, abuse, accident, misapplication, tampering, or alteration; (3) failures due to improper installation, operation,

maintenance or storage; (4) atypical or unapproved application, use or service; (5) failures caused by corrosion, rust or

other foreign materials in the system, or operation at pressures in excess of recommended maximums.

This warranty sets forth manufacturer’s sole obligation and purchaser’s exclusive remedy for defective products.

MANUFACTURER SHALL NOT BE LIABLE FOR ANY CONSEQUENTIAL, INCIDENTAL, OR CONTINGENT DAMAGES

WHATSOEVER. THE FOREGOING LIMITED WARRANTIES ARE EXCLUSIVE AND IN LIEU OF ALL OTHER EXPRESS

AND IMPLIED WARRANTIES, INCLUDING BUT NOT LIMITED TO IMPLIED WARRANTIES OF MERCHANTABILITY

AND FITNESS FOR A PARTICULAR PURPOSE. THE FOREGOING LIMITED WARRANTIES SHALL NOT EXTEND

BEYOND THE DURATION PROVIDED HEREIN.

Some states do not allow the exclusion or limitation of incidental or consequential damages or limitations on how long an

implied warranty lasts, so the above limitations or exclusions may not apply to You. This warranty gives You specic legal

rights and You may also have other rights which vary from state to state.

WARRANTY

Page is loading ...

Eco Flo EFSWJ10P Owner's manual

Eco Flo EFSWJ10P Owner's manual

in other languages

Related papers

Other documents