Stanley SLP2050 User manual

1

Questions, problems, missing parts?

Before returning to your retailer, call our

customer service department at 1-866-508-1330,

8 a.m. - 5:00 p.m., CST, Monday - Friday.

www.stanleypressurewashers.com

2050 PSI

ELECTRIC PRESSURE

WASHER

ASSEMBLY, CARE AND

USE INSTRUCTIONS

Model SLP 2050

IMPORTANT:

RETAIN THESE INSTRUCTIONS AND ATTACH

RECEIPT TO MANUAL FOR FUTURE REFERENCE.

READ CAREFULLY

ALWAYS WEAR EYE PROTECTION TO

PREVENT INJURY TO EYES WHEN

OPERATING THE POWER WASHER.

93919-LP

STANLEY® and the STANLEY® logo are trademarks of Stanley Black & Decker, Inc.

or an affiliate thereof and are used under license.

2

TABLE OF CONTENTS

PRODUCT SPECIFICATIONS

TABLE OF CONTENTS

SPECIFICATIONS

Model

Max PSI

(lbs/sq. in.)

Max GPM

(Gal/per min) Cold Water Volts Amps

Weight (lbs.)

SLP 2050 2050 1.4

✔

120 13 36.4

PRODUCT SPECIFICATIONS

Product Specifications ............................................................................................ 2

Package Contents .................................................................................................. 3

Hardware Contents ................................................................................................ 3

Safety Information ................................................................................................. 4

Assembly Instructions ............................................................................................. 6

Operating Instructions ........................................................................................... 11

Care and Maintenance ......................................................................................... 14

Troubleshooting ................................................................................................... 16

Limited Warranty ................................................................................................. 17

Replacement Parts List ......................................................................................... 18

3

PACKAGE CONTENTS

HARDWARE CONTENTS

PART DESCRIPTION QUANTITY

J Wheels 2

K Spray Gun 1

L Spray Gun Trigger Lock 1

M Spray Gun Holster 1

N Soft PVC Hose 1

O Nozzle Cleaning Wire 1

AA Axle Pin 2

BB Screw 2

CC Screw 2

DD Cotter Pin 2

PART DESCRIPTION QUANTITY

A Hose Holder 1

B Handle 1

*C Rotary Nozzle 1

D O-Ring Replacement Kit 1

*E Quick Connect Nozzles 4

F Power Washer Unit 1

G Lower Frame 1

H Nozzle Holder 1

*I Extension Lance 1

AA

BB

CC

DD

Screw

Qty. 2

Axle Pin

Qty. 2

Screw

Qty. 2

Cotter Pin

Qty. 2

B

F

M

A

N

D

K

J

PW909383SS

*C

*E

*I

L

H

G

Soap – Black

0° – Red

15° – Yellow

25° – Green

O

AA

BB

CC

DD

*Packaged on the power washer unit.

4

SAFETY INFORMATION

4

SAFETY INFORMATION

Please read and understand this entire manual before

attempting to assemble, operate, or install the product.

This manual contains information that relates to

PROTECTING PERSONAL SAFETY and PREVENTING

EQUIPMENT PROBLEMS. It is very important to read this

manual carefully and understand it thoroughly before

using the product. The symbols listed below are used to

indicate this information.

DANGER

Potential hazard that will result in serious injury

or loss of life.

WARNING

Hazard that could result in serious injury or loss

of life.

CAUTION

Potential hazard that may result in moderate

injury or damage to equipment.

Note: The word “Note” is used to inform the reader of

something the operator needs to know about the tool.

WARNING

To reduce the risk of injury, the user must read

and understand the instructions before using

this product.

1. Warning – When using this product basic,

precautions should always be followed, including

the following

2. Read all the instructions before using the product

3. Know how to stop the product and bleed pressures

quickly. Be thoroughly familiar with the controls.

4. Keep operating area clear of persons

5. Do not overreach or stand on unstable support.

Keep good footing and balance at all times.

6. Follow the maintenance instructions as specified in

the manual

7. To avoid personal injury and/or damage to property

and to maximize your power washing experience,

carefully follow all of the safety tips, instructions,

warnings and safeguards and become familiar with

all of the controls.

8. This power washer conforms to CSA and other

safety and consumer standards. DO NOT modify or

rebuild any part of your power washer.

9. DO NOT use your power washer when you are

under the influence of alcohol or drugs. Use this

power tool carefully and only when you are alert.

10. Watch your balance and footing while using your

power washer. Surfaces become slippery when wet

and are extra slippery when using a detergent or

cleaner.

11. NEVER operate the power washer in bare feet,

sandals, or open-toed shoes.

12. When using the power washer near children, make

sure they are closely supervised by an adult to avoid

injury. NEVER let a child use the power washer.

13. Keep fingers, hands, feet and any part of your body

clear of the stream of high pressure water. The

powerful spray can cause blindness or blast holes in

the skin. It can break a window if you are too close

when you pull the trigger on the spray gun.

14. ALWAYS wear eye protection to prevent injury to

eyes when operating the power washer.

15. To avoid mishaps or injury, ALWAYS use the trigger

safety lock when not using the power washer even

if the spraying stops for a moment.

16. The power washer is equipped with a Ground Fault

Circuit Interrupter (GFCI) which greatly reduces the

chance of electric shock while the unit is in use. If

replacement of the plug or cord is needed, use only

identical replacement parts.

17. Point the spray gun in a safe direction when

beginning a power washing session.

18. NEVER spray directly at a person, animal, electrical

device or the unit itself.

19. When first using the spray gun, hold the spray

gun and lance with two hands when pulling the

trigger (one hand to pull the trigger and the other

to stabilize the gun assembly) until you get used to

the “kickback” from the spray gun.

20. When you press the power switch to turn off the

power washer, water pressure may remain in the

system. To discharge the pressure, point the spray

gun in a safe direction and pull the trigger.

21. NEVER spray flammable liquids.

22. NEVER use the power washer in areas that contain

combustible dust, liquids or vapors.

23. Avoid contact of the pressure hose with sharp

objects and examine the hose regularly. Replace

if damaged. Due to the high pressure involved, it

cannot be repaired if cut or damaged.

24. Only use detergent specifically formulated for

power washers and follow instructions on the

detergent’s label.

25. Protect eyes, lungs, and skin from exposure to

5

SAFETY INFORMATION

5

Double Insolated Product

SAFETY INFORMATION

KEEP THESE INSTRUCTIONS FOR FUTURE REFERENCE.

detergent. Dish or laundry soap is too thick and will

clog the nozzle of your detergent bottle.

IMPORTANT: Store the power washer indoors to

prevent the water in the unit from expanding under

freezing conditions. When the water freezes and

expands, your power washer will be damaged and

become inoperable. Or, if storing outdoors, it is

recommended you use pump saver (not included) to

protect pumps.

26. NEVER use hot water with your power washer. It

will overheat and damage the high pressure pump.

27. NEVER leave the power washer unattended while

it is powered “ON”.

28. ALWAYS turn the water supply “ON ” before

turning the power washer power to “ON”.

Running the pump dry will cause damage to the

internal components.

29. NEVER use a water supply to your power washer

that exceeds 150 PSI maximum.

30. NEVER disconnect the high pressure hose from the

power washer while the system is pressurized.

31. NEVER permanently engage the trigger

mechanisms on the spray gun.

32. NEVER operate the power washer unless all

components are properly and securely connected.

33. NEVER allow the power washer pump to run for

more than one minute after you have turned off

the water supply. This can cause the motor and

pump to overheat and fail.

34. NEVER use lances or other parts that are not

compatible for this specific AR Blue Clean unit.

35. NEVER USE AN EXTENSION POWER CORD since it

defeats the effectiveness of the GFCI and increases

the chance of electrocuting the operator.

36. NEVER spray any electrical outlet with your power

washer.

37. Inspect the power cord before using. DO NOT use

it if it is damaged.

Servicing of a Double-Insulated Appliance

Ground Fault Circuit Interrupter Protection:

This pressure washer is provided with a ground-fault

circuit-interrupter (GFCI) built into the plugs of the

power-supply cord. This device provides additional

protection from the risk of electric shock. Should

replacement of the plug or cord become necessary,

use only identical replacement parts that include GFCI

protection.

In a double-insulated product, two systems of

insulation are provided instead of grounding.

Grounding means are not provided for a double

insulated product, nor should grounding means be

added to the product. Servicing a double-insulated

product requires extreme care and knowledge of the

system, and should only be done by qualified service

personnel.

Replacement parts for a double-insulated product must

be identical to the original parts.

A double-insulated product is marked with the words

“Double Insulation” or “Double Insulated”. Product

may also be marked with symbol shown here.

6

PREPARATION

Before beginning assembly of product, make sure

all parts are present. Compare parts with package

contents list and hardware contents list. If any part is

missing or damaged, DO NOT attempt to assemble the

product.

Estimated Assembly Time: 5 minutes

Tools Required for Assembly (not included): Phillips

screwdriver

ASSEMBLY INSTRUCTIONS

PREPARATION

Place a foot on the pad at the front of the lower

frame (G) and then lift the power washer unit (F) off

the frame. Set pressure washer (F) to the side.

2

1

F

G

Axle Pin

x 2

AA

BB

CC

DD

Tornillo

Qty. 2

Perno de eje

Qty. 2

Tornillo

Qty. 2

Pasador de chaveta

Qty. 2

1

2

G

J

AA

DD

Hardware Used:

Frame Assembly

Install axel pins (AA) and wheels (J) to lower frame

(G). Secure with cotter pins (DD).

DD

Cotter Pin

AA

BB

CC

DD

Tornillo

Qty. 2

Perno de eje

Qty. 2

Tornillo

Qty. 2

Pasador de chaveta

Qty. 2

x 2

7

ASSEMBLY INSTRUCTIONS

1

3

2

G

H

BB

4

3

2

1

G

B

Install nozzle holder (H) to lower frame (G). Secure

with two screws (BB).

1

5

2

A

CC

B

Press buttons on lower frame (G) extensions and install

handle (B). Lower frame extensions will click when

handle is in proper position.

Install hose holder (A) onto back side of upper handle

(B). Secure with two screws (CC).

Screw

x 2

BB

AA

BB

CC

DD

Tornillo

Qty. 2

Perno de eje

Qty. 2

Tornillo

Qty. 2

Pasador de chaveta

Qty. 2

Hardware Used:

Screw

x 2

CC

AA

BB

CC

DD

Tornillo

Qty. 2

Perno de eje

Qty. 2

Tornillo

Qty. 2

Pasador de chaveta

Qty. 2

Hardware Used:

8

PREPARATION

ASSEMBLY INSTRUCTIONS

6

B

M

Slide spray gun holster (M) into place on the

upper handle (B).

Place power washer unit (F) into position on the lower

frame (G).

7

F

G

7

F

G

8

1

2

F

G

Pull upward on latches that are located on

sides of lower frame (G). Once upper latch is flush

with the lower lip, push down until lower latch clicks

into place.

3

2

9

1

K

N

Pull back on collar at one end of soft PVC hose (N).

Push firmly to connect hose to spray gun (K). Twist

collar to secure. Confirm hose is locked into spray gun

by slightly pulling on them. The hose is now securely

attached to spray gun.

9

ASSEMBLY INSTRUCTIONS

Locking Spray Gun (before Lance installation) To lock

trigger of spray gun (K), point gun away from you and

turn dial to lock (“3” and “9” position). Squeeze or

pull trigger to make sure it is locked. Always leave in

locked position when not in use. This ensures the gun

is in “safe” mode until it is ready for use. Turn dial to

unlock (“12” and “6” position) to release spray gun

trigger.

Note: The trigger lock prevents trigger from being

accidentally engaged.

10

1

K

Unlocked Locked

ASSEMBLY INSTRUCTIONS

11

*I

K

1

2

12

*I

*E

*C

1

2

13

*I

*E

*C

Extension Lance installation

While spray gun (K) is in the locked position, insert

lance (*I) into the end of spray gun by inserting and

turning clockwise until fully in place. To remove, turn

counterclockwise.

To remove nozzle (*E) and Rotary nozzle (*C), pull back

on collar of lance (*I) and pull out nozzle.

Attach nozzle (*E) and Rotary nozzle (*C) into end of

lance (*I) by pressing selected nozzle into place. It will

make a “click” sound when firmly in place.

Note: Always push safety lock button to lock trigger

when changing lances and nozzles to ensure that they

do not accidentally eject with force during removal.

10

ASSEMBLY INSTRUCTIONS

3

14

1

2

N

F

N

2

1

F

M

*I

K

15

2

1

F

M

*I

K

15

16

NF

Pull back on collar at the other end of soft PVC hose

(N). Push firmly to connect hose to power washer

unit. Twist collar to secure. Confirm hose is locked into

power washer unit by slightly pulling on hose. The

hose is now securely attached.

Insert extension lance (*I) into nozzle holder (H), and

press spray gun (K) with extension lance (*I) into spray

gun holster (M).

Attach a garden hose to built in garden hose

adapter. The water is now connected to your power

washer.

Note: Flush out garden hose before connecting to

garden hose adapter

You have now completed the assembly and are ready

to begin using your electric power washer. Read and

observe all safety instructions.

11

• Push the power button to turn the unit on (red

power light will turn on). The unit will turn on for 1

- 2 seconds and shut off. This is a normal function of

the auto start feature.

• Squeeze the spray gun trigger to begin pressure

washing.

• Begin power washing by squeezing the trigger on the

spray gun all the way into the handle.

• Release the spray gun trigger to stop the power

washer.

• Allow the motor to come to a complete stop before

squeezing the trigger again.

• Squeezing rapidly will cause the auto start feature to

miss an on/off cycle that may prevent it from turning

on while squeezing trigger after rapid squeezing. Use

slow, deliberate trigger pulls to avoid this.

OPERATING INSTRUCTIONS

• Turn on water supply at the faucet to completely open.

• Make sure the power switch is off (light will be off).

• Unwind the power cord completely and plug

into a grounded 120 volt outlet.

• Turn the safety lock button on the spray gun to

unlocked. While pointing the spray gun in a safe

direction, squeeze the trigger on the spray gun until

there is a steady stream of water, letting the water and

air out of the hose.

OFF ON

K

Lock

12

OPERATING INSTRUCTIONS

• When using detergent (not included), fill with a

properly formulated detergent or cleaner with water

ratio according to instructions on the container.

Close detergent tank when done filling.

• Always test a small area to avoid chance of

damaging the surface.

• When removing the detergent tank, squeeze the

clamp and remove the small hose from detergent

tank. Pull the detergent tank straight out. To replace

tank, push straight in and then reattach hose with

clamp.

• The power washer will

pull a ratio of water to

detergent of 10:1 or 10

parts water to 1 part

detergent. The detergent

concentration can be

adjusted by turning the

detergent knob on the

top of the machine. Turn

it left for more concentration or turn it right for less

concentration.

13

OPERATING INSTRUCTIONS

3

2

1

Removing Power Washer Unit from Frame for

Handheld Operation

• Locate latches on the lower side of frame. Unlock

latches by pulling downward on the latches. Place a

foot on the pad at the front of the lower frame and

then lift the power washer unit off the frame.

Operation Tips

• If you hear the motor run intermittently when the

trigger is not being squeezed, that is normal.

The pump is priming itself so it is ready to operate

when the trigger is squeezed. Turn off the power

washer if not being used after five minutes.

• The o-rings on the bayonet end of the nozzle should

be cleaned regularly and lubricated with non-water

soluble grease such as petroleum jelly (not included).

• Keep the nozzle cleaning wire for use in unclogging

the nozzle. If you lose the cleaning wire, a

straightened paper clip also works.

How to Avoid Damaging Surfaces

• Damage to surfaces being cleaned occurs because

the impact force of the water pressure exceeds

the durability of the surface. Bare wood can be

penetrated, paint can be peeled off, etc. You can vary

the force of your power washer by controlling:

1. The angle of the surface being cleaned

2. The distance of the nozzle from the surface being

cleaned

• Never use a narrow high pressure stream of water on

soft surfaces susceptible to damage.

• Use the 25˚ angle quick connect nozzle when

cleaning windows. Be sure to place the nozzle

approximately 4 to 5 ft. away from the window with

the nozzle at 45° angle. Squeeze the trigger and vary

the spray pattern and angle until optimum cleaning

efficiency is achieved.

Using Power Cord

• Remove the power cord from the unit by swiveling

the cord hook to the right or left. The power cord

then can be slid off to either side of the power

washer unit.

• Swivel cord hook back to center when ready to wrap

the cord back into place for storage.

14

CARE AND MAINTENANCE

Detergents

• Use detergents designed for power washers.

Hardware stores or home centers also have power

washer detergents for different cleaning projects. The

cleaning solution should be the consistency of water

in order to prevent clogging your detergent bottle

and nozzle.

• This system applies detergent under low pressure.

The cleaning power of the detergents is enhanced

when applied with low pressure and enough time is

given to break down dirt and grime. The combination

of low pressure and chemical action is very effective

and can be better than scrubbing if applied properly.

Always spray detergent on a dry surface. Do not

pre-soak area. Wetting the surface first dilutes

the detergent and reduces its cleaning ability. Do

not allow detergent to dry on surface. On vertical

surfaces being cleaned, apply detergent to lower

surfaces and work your way up to prevent detergent

from causing streaks in the dirt and grime. Rinse

detergent by pressure washing from bottom up for

same reason.

• If a stain is particularly tough, it may be necessary

to reapply the detergent and use a bristled brush to

scrub the stain. Subsequent power washing after

brushing should successfully complete your cleaning

job.

Cleaning Garden Hose Adapter

• The screens inside the adapter should be cleaned

periodically. Rinse with clean water, and then place

back in the adapter.

Cleaning Nozzles

• A clogged or partially clogged nozzle can cause

significant reduction of water pressure coming out

of the nozzle and/or cause the unit to pulsate while

spraying.

• Turn off the unit.

• Turn off the water supply to the unit.

• Relieve any pressure trapped in the hose by squeezing

the trigger 2 - 3 times, then lock the spray gun by

turning the dial to lock (“3” and “9” position).

• Using the nozzle tip cleaner provided (or an unfolded

paper clip), insert the wire into the nozzle hole and

move back and forth until debris is dislodged.

• Back flush water through the nozzles using garden

hose and highest pressure available (either standard

water nozzle or use your thumb over the nozzle to

create water pressure for back flush).

15

Storage

• When your pressure washing session has been

completed, turn off the power switch. Unplug the

power cord from the outlet. Turn off the water

supply. Pull the trigger on the spray gun 2 - 3 times

to drain out the excess water and to release any

remaining water pressure. Do not allow the power

washer to run with no water flowing through it.

• Remove detergent tank and clean completely.

Residual chemical will stick to the container and can

cause the detergent injector to clog and not function

properly.

• Remove high pressure hose from spray gun and

unscrew the other end of the high pressure hose

from the power washer.

• Remove lance from the gun. Place the gun in

the holder on the side. Make sure to discard any

remaining detergent from the tank. Flush the

tank and nozzle head with fresh water to prevent

clogging.

• Hook the power cord around the L-shaped tab on the

top of the machine.

• The pressure hose is stored on the hose hook located

on the back of the handle.

• DO NOT store the power washer where it is

exposed to freezing temperatures unless you

use an antifreeze designed for pumps. It is

recommended that you use this antifreeze (not

included) for storing in freezing temperatures.

Freezing will damage the pump unless this is added

to the power washer. If not using or if storing your

power washer for more than one month, it is also

recommended that an antifreeze is used to protect

the pump.

CARE AND MAINTENANCE

16

TROUBLESHOOTING

PROBLEM CORRECTIVE ACTION

Unit will not turn on.

1. Make sure the power washer is OFF. Plug in the electrical cord to a grounded 120 volt

outlet (no electrical extension cord should be used). If the electrical cord will not plug

into your outlet, your electrical outlet is not properly grounded and should not be

used. Use another electrical outlet.

2. If this did not correct the problem, try plugging into another electrical outlet and

repeat the above procedure. If it is still not working, call Customer Service. 1-866-508-

1330

The high pressure

(HP) hose will

not connect/stay

connected to the

spray gun. Is this a

spray gun problem?

1. In most cases, the spray gun is not the problem. The problem is the rubber sleeve

covering the fitting at the end of the high pressure hose. It has likely slipped up

toward the metal tip. To fix: wiggle, twist and/or pull the rubber sleeve down until the

entire tip is visible plus an 1/8 in. of the metal fitting below the tip. Now try to insert

the hose tip into the spray gun. It should “click” into place and will not come out until

the hose is released by pushing in the lever on the underside of the gun. You may cut

away the end of the sleeve with a sharp knife if unable to move the sleeve down. Be

careful not to cut or puncture the hose.

The unit is running

but there is no water

flow.

1. Check the water source. Unclog the nozzle on the lance. (See nozzle cleaning

instructions under “Cleaning nozzles”.) Or take off the lance and spray out of the

spray gun. This will indicate if the problem is with the lance.

Why is water leaking

where the high

pressure hose connects

to the spray gun?

1. Make sure there is an o-ring (included with package contents) at the end of the metal

tip of the high pressure hose. If no o-ring is present, the connection between the hose

and spray gun will leak.

I can’t remove the

lance from the spray

gun. What should I

do?

1. All lances are attached and removed from the spray gun in the same manner. Insert

the end of the lance into the spray gun. Press the spray gun and lance together (about

a 1/8 in.) and turn the collar of the gun clockwise. The lance will lock in place. Remove

the lance by reversing this procedure. Press the spray gun and lance together and turn

counter clockwise. The lance will slide out.

2. Hold the spray gun and lance in an upright position with the nozzle end on the floor.

Push the whole assembly straight down to loosen the connection, and then follow

the removal process again. You may also spray soapy water or a lubricant in the area

where the lance connects to the spray gun

The power washer

turns on for

2 seconds, shuts off,

and will not turn

back on. Do I have a

defective unit?

1. When the water is connected, the accessories are assembled properly, and the power

is turned on, the power washer may turn on for 1 - 2 seconds to prime the pump. It

automatically shuts off and waits for the spray gun trigger to be pressed. When the

trigger is pressed, water starts flowing through the pump. The water sensor in the

pump “senses” the moving water and automatically turns the power washer on.

2. Turn the power off, hold in the trigger on the spray gun so that you have a steady

stream of water. While you are holding the trigger open on the spray gun, at the same

time, turn the power on.

TROUBLESHOOTING

If you have any questions regarding the product, please call customer service at 1-866-508-1330

17

TROUBLESHOOTING

LIMITED WARRANTY

The Warranty of this product is coverd by A.R.North America.

This product has a 2 (two) year warranty. Please read the following carefully to understand what each warranty

entails:

This product is under warranty to the original retail consumer against defects in material and workmanship for a

period 1(one) year and is a complete “bumper to bumper” warranty including the spray gun,the high pressure

hose and all accessories from the date of purchase. The warranty is not transferable or assignable. This warranty

covers replacement parts. This limited one year warranty applies only to products used in consumer applications

and is void in rental or any commercial application. Reasonable care must be used in conformity with operation

and maintenance instructions in the owner’s manual and quick start guide. Failure to follow these instructions will

void this warranty. This warranty gives you special legal rights and you may also have other rights which vary from

state to state.

The second year of the warranty only covers manufacturer defects.

Warranty Process

Keep your original receipt of purchase in case of warranty claim.

If your power washer develops a problem, contact Customer Service:

• Call our toll-free number at 1-866-508-1330. Customer Service is available Monday - Friday 8:00 a.m. to 5:00

p.m. Central Standard Time (CST). The Customer Service person will work with you to fix the problem.

If the power washer needs to be returned for repair, shipping costs to the company must be paid by the

customer. A Return Merchandise Authorization (RMA) Number will be issued for the return. Upon receiving

the power washer, the company will repair or replace the unit. We will send unit back to customer at no charge.

Please note: Power washers sent to the company without an RMA Number will NOT be accepted and shipped

back at the expense of the sender.

Return address:

A.R. North America, Inc.

140 81

st

Avenue North East

Fridley, MN 55432

Manufactured by:

A.R. North America, Inc.

140 81

st

Avenue North East Fridley, MN 55432

LIMITED WARRANTY

18

REPLACEMENT PARTS LIST

PART DESCRIPTION PART #

G

Soap QC Nozzle PW4221470

H

0° QC Nozzle PW4221430

I

15° QC Nozzle PW4221440

J

25° QC Nozzle PW4221450

K Axle Pin

PW4620370

L Cotter Pin

PW4620380

M Garden Hose Adapter

PW4221580

PART DESCRIPTION PART #

A Rotary Nozzle

PW4220680

B O-Ring Replacement Kit

PW909383SS

C Extension Lance

PW3400960

D Wheel

PW4620410

E Spray Gun

PW4221420

F Soft PVC Hose

PW4221550

Soap – Black

0° – Red

15° – Yellow

25° – Green

F

K

G

B

PW909383SS

A

E

C

M

D

L

H

I

J

For replacement parts, call our customer service department at 1-866-508-1330, 8 a.m. - 5:00 p.m., CST,

Monday - Friday or order online at www.stanleypressurewashers.com

Printed in China

Manufactured by:

A.R. North America, Inc.

140 81

st

Avenue North East Fridley, MN 55432

STANLEY® and the STANLEY® logo are trademarks of

Stanley Black & Decker, Inc. or an affiliate thereof

and are used under license.

Made in China

19

Questions, problèmes, pièces manquantes?

Avant de retourner l’appareil chez le marchand,

communiquez avec le service à la clientèle au

1-866-508-1330, de 8 h à 17 h, HNC,

du lundi au vendredi.

www.stanleypressurewashers.com

2050 PSI

LAVEUSE À PRESSION

ÉLECTRIQUE

GUIDED’ASSEMBLAGE,

D’ENTRETIEN ET

D’UTILISATION

Modèle SLP 2050

IMPORTANT :

CONSERVER CE GUIDE ET INSÉRER LA FACTURE

DANS LE GUIDE POUR RÉFÉRENCE ULTÉRIEURE.

LIRE ATTENTIVEMENT

AFIN DE PRÉVENIR LES BLESSURES AUX

YEUX, PORTER TOUJOURS DES LUNETTES

DE SÉCURITÉ PENDANT L’UTILISATION DE

LA LAVEUSE À PRESSION.

93919-LP

STANLEY® and the STANLEY® logo are trademarks of Stanley Black & Decker, Inc.

or an affiliate thereof and are used under license.

Page is loading ...

LIMITED WARRANTY

36

LISTE DES PIÈCES DE RECHANGE

PIÈCE DESCRIPTION NO DE

PIÈCE

H Buse de 0° à raccord rapide PW4221430

I Buse de 15° à raccord rapide PW4221440

J Buse de 25° à raccord rapide PW4221450

K Cheville d’essieu PW4620370

L Goupille fendue PW4620380

M Adaptateur pour tuyau

d’arrosage

PW4221580

PIÈCE DESCRIPTION NO DE

PIÈCE

A Buse rotative PW4220680

B Kit de remplacement de joint

torique

PW909383SS

C Lance PW3400960

D Roues PW4620410

E Pistolet de pulvérisation PW4221420

F Tuyau en PVC souple PW4221550

G Buse à savon à raccord rapide PW4221470

Savon – noir

0° – rouge

15° – jaune

25° – vert

F

K

G

B

PW909383SS

A

E

C

M

D

L

H

I

J

Pour les pièces de rechange, communiquez avec le service à la clientèle au numéro 1-866-508-1330, 8 h à 17 h,

HNC, du lundi au vendredi ou commandez en ligne à l’adresse www.stanleypressurewashers.com.

Imprimé en Chine

Fabriqué par :

A.R. North America, Inc.

140 81

st

Avenue North East Fridley, MN 55432

STANLEY® and the STANLEY® logo are trademarks of

Stanley Black & Decker, Inc. or an affiliate thereof

and are used under license.

Made in China

Page is loading ...

Stanley SLP2050 User manual

Stanley SLP2050 User manual

in other languages

Related papers

Other documents