Makita BHP442 User manual

Category
Power drills
Type
User manual

This manual is also suitable for

GB Cordless Percussion-Driver Drill Instruction manual
ID Bor Obeng Perkusi Tanpa Kab Petunjuk penggunaan
VI Máy Khoan-vn Vít chy Pin Tài liu hng dn
TH
 
BHP442
BHP452
2
1 007699 2 008348
3 008353 4 008349
5 008350 6 008351
7 008352 8 007700
1
2
3
4
5
A
B
6
7
8
9
10
11
12
13
14
3
9 008410 10 002449
11 008354 12 006258
13 008355 14 007428
15 007429 16 006304
15
16
17
18
19
20
16
21
22
23
24
25
24
4
ENGLISH
Explanation of general view
SPECIFICATIONS
•Due to our continuing programme of research and development, the specifications herein are subject to change without
notice.
•Specifications and battery cartridge may differ from country to country.
•Weight, with battery cartridge, according to EPTA-Procedure 01/2003
END004-4
Symbols
The following show the symbols used for the equipment.
Be sure that you understand their meaning before use.
..... Read instruction manual.
ENE039-1
Intended use
The tool is intended for impact drilling in brick, concrete
and stone as well as for drilling without impact in wood,
metal, ceramic and plastic.
GEA006-2
General Power Tool Safety
Warnings
WARNING! Read all safety warnings and all
instructions. Failure to follow the warnings and
instructions may result in electric shock, fire and/or
serious injury.
Save all warnings and
instructions for future reference.
The term “power tool” in the warnings refers to your
mains-operated (corded) power tool or battery-operated
(cordless) power tool.
Work area safety
1. Keep work area clean and well lit. Cluttered or dark
areas invite accidents.
2. Do not operate power tools in explosive
atmospheres, such as in the presence of
flammable liquids, gases or dust. Power tools
create sparks which may ignite the dust or fumes.
3. Keep children and bystanders away while
operating a power tool. Distractions can cause you
to lose control.
Electrical safety
4. Power tool plugs must match the outlet. Never
modify the plug in any way. Do not use any
adapter plugs with earthed (grounded) power
tools. Unmodified plugs and matching outlets will
reduce risk of electric shock.
1. Red part
2. Button
3. Battery cartridge
4. Switch trigger
5. Lamp
6. Reversing switch lever
7. Speed change lever
8. Action mode changing ring
9. Adjusting ring
10. Graduation
11. Arrow
12. Sleeve
13. Bit holder
14. Bit
15. Groove
16. Screw
17. Hook
18. Blow-out bulb
19. Limit mark
20. Rear cover
21. Recessed part
22. Spring
23. Arm
24. Carbon brush cap
25. Hole
Model BHP442 BHP452
Capacities
Concrete 13 mm
Steel 13 mm
Wood 38 mm
Wood screw 6 mm x 75 mm 10 mm x 89 mm
Machine screw M6 M6
No load speed (min
-1
)
High (2) 0 - 1,400 0 - 1,500
Low (1) 0 - 400 0 - 400
Blows per minute
High (2) 0 - 21,000 0 - 22,500
Low (1) 0 - 6,000 0 - 6,000
Overall length 215 mm 215 mm
Net weight 1.8 kg 1.7 kg
Rated voltage D.C. 14.4 V D.C. 18 V
5
5. Avoid body contact with earthed or grounded
surfaces such as pipes, radiators, ranges and
refrigerators. There is an increased risk of electric
shock if your body is earthed or grounded.
6. Do not expose power tools to rain or wet
conditions. Water entering a power tool will increase
the risk of electric shock.
7. Do not abuse the cord. Never use the cord for
carrying, pulling or unplugging the power tool.
Keep cord away from heat, oil, sharp edges or
moving parts. Damaged or entangled cords increase
the risk of electric shock.
8. When operating a power tool outdoors, use an
extension cord suitable for outdoor use. Use of a
cord suitable for outdoor use reduces the risk of
electric shock.
9. If operating a power tool in a damp location is
unavoidable, use a ground fault circuit interrupter
(GFCI) protected supply. Use of an GFCI reduces
the risk of electric shock.
Personal safety
10. Stay alert, watch what you are doing and use
common sense when operating a power tool. Do
not use a power tool while you are tired or under
the influence of drugs, alcohol or medication. A
moment of inattention while operating power tools
may result in serious personal injury.
11. Use personal protective equipment. Always wear
eye protection. Protective equipment such as dust
mask, non-skid safety shoes, hard hat, or hearing
protection used for appropriate conditions will reduce
personal injuries.
12. Prevent unintentional starting. Ensure the switch
is in the off-position before connecting to power
source and/or battery pack, picking up or carrying
the tool. Carrying power tools with your finger on the
switch or energising power tools that have the switch
on invites accidents.
13. Remove any adjusting key or wrench before
turning the power tool on. A wrench or a key left
attached to a rotating part of the power tool may result
in personal injury.
14. Do not overreach. Keep proper footing and
balance at all times. This enables better control of
the power tool in unexpected situations.
15. Dress properly. Do not wear loose clothing or
jewellery. Keep your hair, clothing, and gloves
away from moving parts. Loose clothes, jewellery or
long hair can be caught in moving parts.
16. If devices are provided for the connection of dust
extraction and collection facilities, ensure these
are connected and properly used. Use of dust
collection can reduce dust-related hazards.
Power tool use and care
17. Do not force the power tool. Use the correct power
tool for your application. The correct power tool will
do the job better and safer at the rate for which it was
designed.
18. Do not use the power tool if the switch does not
turn it on and off. Any power tool that cannot be
controlled with the switch is dangerous and must be
repaired.
19. Disconnect the plug from the power source and/or
the battery pack from the power tool before
making any adjustments, changing accessories,
or storing power tools. Such preventive safety
measures reduce the risk of starting the power tool
accidentally.
20. Store idle power tools out of the reach of children
and do not allow persons unfamiliar with the
power tool or these instructions to operate the
power tool. Power tools are dangerous in the hands
of untrained users.
21. Maintain power tools. Check for misalignment or
binding of moving parts, breakage of parts and
any other condition that may affect the power
tool’s operation. If damaged, have the power tool
repaired before use. Many accidents are caused by
poorly maintained power tools.
22. Keep cutting tools sharp and clean. Properly
maintained cutting tools with sharp cutting edges are
less likely to bind and are easier to control.
23. Use the power tool, accessories and tool bits etc.
in accordance with these instructions, taking into
account the working conditions and the work to
be performed. Use of the power tool for operations
different from those intended could result in a
hazardous situation.
Battery tool use and care
24. Recharge only with the charger specified by the
manufacturer. A charger that is suitable for one type
of battery pack may create a risk of fire when used
with another battery pack.
25. Use power tools only with specifically designated
battery packs. Use of any other battery packs may
create a risk of injury and fire.
26. When battery pack is not in use, keep it away from
other metal objects, like paper clips, coins, keys,
nails, screws or other small metal objects, that can
make a connection from one terminal to another.
Shorting the battery terminals together may cause
burns or a fire.
27. Under abusive conditions, liquid may be ejected
from the battery; avoid contact. If contact
accidentally occurs, flush with water. If liquid
contacts eyes, additionally seek medical help.
Liquid ejected from the battery may cause irritation or
burns.
Service
28. Have your power tool serviced by a qualified
repair person using only identical replacement
parts. This will ensure that the safety of the power tool
is maintained.
29. Follow instruction for lubricating and changing
accessories.
30. Keep handles dry, clean and free from oil and
grease.
6
GEB056-4
CORDLESS HAMMER DRIVER
DRILL SAFETY WARNINGS
1. Wear ear protectors with impact drilling. Exposure
to noise can cause hearing loss.
2. Use auxiliary handle(s), if supplied with the tool.
Loss of control can cause personal injury.
3. Hold power tool by insulated gripping surfaces,
when performing an operation where the cutting
accessory may contact hidden wiring. Cutting
accessory contacting a “live” wire may make exposed
metal parts of the power tool “live” and could give the
operator an electric shock.
4. Hold power tool by insulated gripping surfaces,
when performing an operation where the fastener
may contact hidden wiring. Fasteners contacting a
“live” wire may make exposed metal parts of the
power tool “live” and could give the operator an
electric shock.
5. Always be sure you have a firm footing.
Be sure no one is below when using the tool in
high locations.
6. Hold the tool firmly.
7. Keep hands away from rotating parts.
8. Do not leave the tool running. Operate the tool
only when hand-held.
9. Do not touch the bit or the workpiece immediately
after operation; they may be extremely hot and
could burn your skin.
10. Some material contains chemicals which may be
toxic. Take caution to prevent dust inhalation and
skin contact. Follow material supplier safety data.
SAVE THESE INSTRUCTIONS.
WARNING:
DO NOT let comfort or familiarity with product (gained
from repeated use) replace strict adherence to safety
rules for the subject product. MISUSE or failure to
follow the safety rules stated in this instruction
manual may cause serious personal injury.
ENC007-6
IMPORTANT SAFETY
INSTRUCTIONS
FOR BATTERY CARTRIDGE
1. Before using battery cartridge, read all
instructions and cautionary markings on (1)
battery charger, (2) battery, and (3) product using
battery.
2. Do not disassemble battery cartridge.
3. If operating time has become excessively shorter,
stop operating immediately. It may result in a risk
of overheating, possible burns and even an
explosion.
4. If electrolyte gets into your eyes, rinse them out
with clear water and seek medical attention right
away. It may result in loss of your eyesight.
5. Do not short the battery cartridge:
(1) Do not touch the terminals with any
conductive material.
(2) Avoid storing battery cartridge in a container
with other metal objects such as nails, coins,
etc.
(3) Do not expose battery cartridge to water or
rain.
A battery short can cause a large current flow,
overheating, possible burns and even a
breakdown.
6. Do not store the tool and battery cartridge in
locations where the temperature may reach or
exceed 50°C (122°F).
7. Do not incinerate the battery cartridge even if it is
severely damaged or is completely worn out. The
battery cartridge can explode in a fire.
8. Be careful not to drop or strike battery.
9. Do not use a damaged battery.
SAVE THESE INSTRUCTIONS.
Tips for maintaining maximum battery life
1. Charge the battery cartridge before completely
discharged.
Always stop tool operation and charge the battery
cartridge when you notice less tool power.
2. Never recharge a fully charged battery cartridge.
Overcharging shortens the battery service life.
3. Charge the battery cartridge with room
temperature at 10°C - 40°C (50°F - 104°F). Let a hot
battery cartridge cool down before charging it.
FUNCTIONAL DESCRIPTION
CAUTION:
Always be sure that the tool is switched off and the
battery cartridge is removed before adjusting or
checking function on the tool.
Installing or removing battery cartridge
(Fig. 1)
•Always switch off the tool before insertion or removal of
the battery cartridge.
To remove the battery cartridge, withdraw it from the
tool while sliding the button on the side of the cartridge.
•To insert the battery cartridge, align the tongue on the
battery cartridge with the groove in the housing and slip
it into place. Always insert it all the way until it locks in
place with a little click. If you can see the red part on
the upper side of the button, it is not locked completely.
Insert it fully until the red part cannot be seen. If not, it
may accidentally fall out of the tool, causing injury to
you or someone around you.
•Do not use force when inserting the battery cartridge. If
the cartridge does not slide in easily, it is not being
inserted correctly.
7
Switch action (Fig. 2)
CAUTION:
•Before inserting the battery cartridge into the tool,
always check to see that the switch trigger actuates
properly and returns to the “OFF” position when
released.
To start the tool, simply pull the switch trigger. Tool speed
is increased by increasing pressure on the switch trigger.
Release the switch trigger to stop.
Lighting up the front lamp (Fig. 3)
CAUTION:
•Do not look in the light or see the source of light
directly.
Pull the switch trigger to light up the lamp. The lamp
keeps on lighting while the switch trigger is being pulled.
The lamp goes out 10 - 15 seconds after releasing the
trigger.
NOTE:
•Use a dry cloth to wipe the dirt off the lens of lamp. Be
careful not to scratch the lens of lamp, or it may lower
the illumination.
Reversing switch action (Fig. 4)
This tool has a reversing switch to change the direction of
rotation. Depress the reversing switch lever from the A
side for clockwise rotation or from the B side for
counterclockwise rotation.
When the reversing switch lever is in the neutral position,
the switch trigger cannot be pulled.
CAUTION:
•Always check the direction of rotation before operation.
•Use the reversing switch only after the tool comes to a
complete stop. Changing the direction of rotation
before the tool stops may damage the tool.
When not operating the tool, always set the reversing
switch lever to the neutral position.
Speed change (Fig. 5)
To change the speed, first switch off the tool and then
slide the speed change lever to the2” side for high speed
or “1” side for low speed. Be sure that the speed change
lever is set to the correct position before operation. Use
the right speed for your job.
CAUTION:
•Always set the speed change lever fully to the correct
position. If you operate the tool with the speed change
lever positioned halfway between the “1” side and “2”
side, the tool may be damaged.
Do not use the speed change lever while the tool is
running. The tool may be damaged.
Selecting the action mode (Fig. 6)
This tool employs an action mode changing ring. Select
one of the three modes suitable for your work needs by
using this ring.
For rotation only, turn the ring so that the arrow on the tool
body points toward the mark on the ring.
For rotation with hammering, turn the ring so that the
arrow points toward the mark on the ring.
For rotation with clutch, turn the ring so that the arrow
points toward the mark on the ring.
CAUTION:
Always set the ring correctly to your desired mode
mark. If you operate the tool with the ring positioned
halfway between the mode marks, the tool may be
damaged.
Adjusting the fastening torque (Fig. 6)
The fastening torque can be adjusted in 16 steps by
turning the adjusting ring so that its graduations are
aligned with the arrow on the tool body. The fastening
torque is minimum when the number 1 is aligned with the
arrow, and maximum when the number 16 is aligned with
the arrow.
Before actual operation, drive a trial screw into your
material or a piece of duplicate material to determine
which torque level is required for a particular application.
ASSEMBLY
CAUTION:
Always be sure that the tool is switched off and the
battery cartridge is removed before carrying out any
work on the tool.
Installing or removing driver bit or drill bit
(Fig. 7)
Turn the sleeve counterclockwise to open the chuck jaws.
Place the bit in the chuck as far as it will go. Turn the
sleeve clockwise to tighten the chuck.
To remove the bit, turn the sleeve counterclockwise.
Installing bit holder (accessory) (Fig. 8)
Fit the bit holder into the protrusion at the tool foot on
either right or left side and secure it with a screw.
When not using the driver bit, keep it in the bit holders.
Bits 45 mm long can be kept there.
Hook (Accessory) (Fig. 9)
The hook is convenient for temporarily hanging the tool.
This can be installed on either side of the tool.
To install the hook, insert it into a groove in the tool
housing on either side and then secure it with a screw. To
remove, loosen the screw and then take it out.
OPERATION
CAUTION:
•Always insert the battery cartridge all the way until it
locks in place. If you can see the red part on the upper
side of the button, it is not locked completely. Insert it
fully until the red part cannot be seen. If not, it may
accidentally fall out of the tool, causing injury to you or
someone around you.
Hold the tool firmly with one hand on the grip and the
other hand on the bottom of the battery cartridge to
control the twisting action.
Hammer drilling operation
CAUTION:
•There is a tremendous and sudden twisting force
exerted on the tool/bit at the time of hole break-
through, when the hole becomes clogged with chips
8
and particles, or when striking reinforcing rods
embedded in the concrete.
First, turn the action mode changing ring so that the arrow
on the tool body points to the marking. The adjusting
ring can be aligned in any torque levels for this operation.
Be sure to use a tungsten-carbide tipped bit.
Position the bit at the desired location for the hole, then
pull the switch trigger. Do not force the tool. Light pressure
gives best results. Keep the tool in position and prevent it
from slipping away from the hole.
Do not apply more pressure when the hole becomes
clogged with chips or particles. Instead, run the tool at an
idle, then remove the bit partially from the hole. By
repeating this several times, the hole will be cleaned out
and normal drilling may be resumed.
Blow-out bulb (optional accessory)
(Fig. 10)
After drilling the hole, use the blow-out bulb to clean the
dust out of the hole.
Screwdriving operation (Fig. 11)
First, turn the action mode changing ring so that the arrow
on the tool body points to the marking. Adjust the
adjusting ring to the proper torque level for your work.
Then proceed as follows.
Place the point of the driver bit in the screw head and
apply pressure to the tool. Start the tool slowly and then
increase the speed gradually. Release the switch trigger
as soon as the clutch cuts in.
CAUTION:
Make sure that the driver bit is inserted straight in the
screw head, or the screw and/or bit may be damaged.
NOTE:
•When driving wood screws, predrill pilot holes to make
driving easier and to prevent splitting of the workpiece.
See the chart.
006421
Drilling operation
First, turn the adjusting ring so that the pointer points to
the marking. Then proceed as follows.
CAUTION:
•Pressing excessively on the tool will not speed up the
drilling. In fact, this excessive pressure will only serve
to damage the tip of your bit, decrease the tool
performance and shorten the service life of the tool.
•There is a tremendous force exerted on the tool/bit at
the time of hole break through. Hold the tool firmly and
exert care when the bit begins to break through the
workpiece.
•A stuck bit can be removed simply by setting the
reversing switch to reverse rotation in order to back
out. However, the tool may back out abruptly if you do
not hold it firmly.
•Always secure small workpieces in a vise or similar
hold-down device.
If the tool is operated continuously until the battery
cartridge has discharged, allow the tool to rest for 15
minutes before proceeding with a fresh battery.
Drilling in wood
When drilling in wood, the best results are obtained with
wood drills equipped with a guide screw. The guide screw
makes drilling easier by pulling the bit into the workpiece.
Drilling in metal
To prevent the bit from slipping when starting a hole, make
an indentation with a center-punch and hammer at the
point to be drilled. Place the point of the bit in the
indentation and start drilling.
Use a cutting lubricant when drilling metals. The
exceptions are iron and brass which should be drilled dry.
MAINTENANCE
CAUTION:
Always be sure that the tool is switched off and the
battery cartridge is removed before attempting to
perform inspection or maintenance.
•Never use gasoline, benzine, thinner, alcohol or the
like. Discoloration, deformation or cracks may result.
Replacing carbon brushes
Replace when they wear down to the limit mark. Keep the
carbon brushes clean and free to slip in the holders. Both
carbon brushes should be replaced at the same time. Use
only identical carbon brushes. (Fig. 12)
Use a screwdriver to remove two screws then remove the
rear cover. (Fig. 13)
Raise the arm part of the spring and then place it in the
recessed part of the housing with a slotted bit screwdriver
of slender shaft or the like. (Fig. 14)
Use pliers to remove the carbon brush caps of the carbon
brushes. Take out the worn carbon brushes, insert the
new ones and replace the carbon brush caps in reverse.
(Fig. 15)
Make sure that the carbon brush caps have fit into the
holes in brush holders securely. (Fig. 16)
Reinstall the rear cover and tighten two screws securely.
To maintain product SAFETY and RELIABILITY, repairs,
any other maintenance or adjustment should be
performed by Makita Authorized Service Centers, always
using Makita replacement parts.
OPTIONAL ACCESSORIES
CAUTION:
•These accessories or attachments are recommended
for use with your Makita tool specified in this manual.
The use of any other accessories or attachments might
Nominal diameter of
wood screw (mm)
Recommended size of
pilot hole (mm)
3.1 2.0 - 2.2
3.5 2.2 - 2.5
3.8 2.5 - 2.8
4.5 2.9 - 3.2
4.8 3.1 - 3.4
5.1 3.3 - 3.6
5.5 3.7 - 3.9
5.8 4.0 - 4.2
6.1 4.2 - 4.4
9
present a risk of injury to persons. Only use accessory
or attachment for its stated purpose.
If you need any assistance for more details regarding
these accessories, ask your local Makita Service Center.
•Drill bits
•Tungsten-carbide tipped hammer bit
•Phillips bit
•Slotted bit
•Socket bit
•Blow-out bulb
•Safety goggles
•Various type of Makita genuine batteries and chargers
•Hook
•Rubber pad assembly
•Wool bonnet
•Foam polishing pad
NOTE:
•Some items in the list may be included in the tool
package as standard accessories. They may differ from
country to country.
10
BAHASA INDONESIA
Penjelasan tampilan keseluruhan
SPESIFIKASI
•Karena kesinambungan program penelitian dan pengembangan kami, spesifikasi yang disebutkan di sini dapat
berubah tanpa pemberitahuan.
•Spesifikasi dan baterai dapat berbeda dari satu negara ke negara lainnya.
Berat, dengan baterai, menurut Prosedur EPTA 01/2003
END004-4
Simbol
Berikut ini adalah simbol-simbol yang digunakan pada
peralatan ini. Pastikan Anda mengerti makna masing-
masing simbol sebelum menggunakan alat.
..... Baca petunjuk penggunaan.
ENE039-1
Penggunaan
Mesin ini digunakan untuk membor kejut batu bata, beton
dan batu serta juga untuk membor tanpa kejut kayu,
logam, keramik dan plastik.
GEA006-2
Peringatan Keselamatan Umum
Mesin Listrik
PERINGATAN! Bacalah semua peringatan
keselamatan dan semua petunjuk. Kelalaian mematuhi
peringatan dan petunjuk dapat menyebabkan sengatan
listrik, kebakaran dan/atau cedera serius.
Simpanlah semua peringatan dan
petunjuk untuk acuan di masa
depan.
Istilah “mesin listrik” dalam semua peringatan mengacu
pada mesin listrik yang dijalankan dengan sumber listrik
jala-jala (berkabel) atau baterai (tanpa kabel).
Keselamatan tempat kerja
1. Jaga tempat kerja selalu bersih dan
berpenerangan cukup. Tempat kerja yang
berantakan dan gelap mengundang kecelakaan.
2. Jangan gunakan mesin listrik dalam lingkungan
yang mudah meledak, misalnya jika ada cairan,
gas, atau debu yang mudah menyala. Mesin listrik
menimbulkan bunga api yang dapat menyalakan debu
atau uap tersebut.
3. Jauhkan anak-anak dan orang lain saat
menggunakan mesin listrik. Bila perhatian terpecah,
anda dapat kehilangan kendali.
1. Bagian berwarna merah
2. Tombol
3. Baterai
4. Saklar pemicu
5. Lampu
6. Tuas saklar pembalik arah
7. Tuas pengubah kecepatan
8. Tombol pengubah mode kerja
9. Cincin penyetel
10. Skala
11. Tanda panah
12. Selongsong
13. Penahan mata mesin
14. Mata mesin
15. Alur
16. Sekrup
17. Kait
18. Penghembus angin
19. Tanda batas
20. Tutup belakang
21. Bagian cekung
22. Pegas
23. Lengan
24. Tutup sikat karbon
25. Lubang
Model BHP442 BHP452
Kapasitas
Beton 13 mm
Baja 13 mm
Kayu 38 mm
Sekrup kayu 6 mm x 75 mm 10 mm x 89 mm
Sekrup mesin M6 M6
Kecepatan tanpa beban (min
-1
)
Tinggi (2) 0 - 1.400 0 - 1.500
Rendah (1) 0 - 400 0 - 400
Hembusan per menit
Tinggi (2) 0 - 21.000 0 - 22.500
Rendah (1) 0 - 6.000 0 - 6.000
Panjang keseluruhan 215 mm 215 mm
Berat bersih 1,8 kg 1,7 kg
Tegangan terukur D.C. 14,4 V D.C. 18 V
11
Keamanan kelistrikan
4. Steker mesin listrik harus cocok dengan
stopkontak. Jangan sekali-kali mengubah steker
dengan cara apa pun. Jangan menggunakan
steker adaptor dengan mesin listrik berarde
(dibumikan). Steker yang tidak diubah dan
stopkontak yang cocok akan mengurangi risiko
sengatan listrik.
5. Hindari sentuhan tubuh dengan permukaan
berarde atau yang dibumikan seperti pipa,
radiator, kompor, dan kulkas. Risiko sengatan listrik
bertambah jika tubuh Anda terbumikan atau terarde.
6. Jangan membiarkan mesin listrik kehujanan atau
kebasahan. Air yang masuk ke dalam mesin listrik
akan meningkatkan risiko sengatan listrik.
7. Jangan menyalahgunakan kabel. Jangan sekali-
kali menggunakan kabel untuk membawa,
menarik, atau mencabut mesin listrik dari
stopkontak. Jauhkan kabel dari panas, minyak,
tepian tajam, atau bagian yang bergerak.
Kabel yang rusak atau kusut memperbesar risiko
sengatan listrik.
8. Bila menggunakan mesin listrik di luar ruangan,
gunakan kabel ekstensi yang sesuai untuk
penggunaan di luar ruangan. Penggunaan kabel
yang sesuai untuk penggunaan luar ruangan
mengurangi risiko sengatan listrik.
9. Jika mengoperasikan mesin listrik di lokasi
lembap tidak terhindarkan, gunakan pasokan daya
yang dilindungi pemutus rangkaian salah arde
(ground fault circuit interrupter - GFCI).
Penggunaan GFCI mengurangi risiko sengatan listrik.
Keselamatan diri
10. Jaga kewaspadaan, perhatikan pekerjaan Anda
dan gunakan akal sehat bila menggunakan mesin
listrik. Jangan menggunakan mesin listrik saat
Anda lelah atau di bawah pengaruh obat bius,
alkohol, atau obat. Sekejap saja lalai saat
menggunakan mesin listrik dapat menyebabkan
cedera diri yang serius.
11. Gunakan alat pelindung diri. Selalu gunakan
pelindung mata. Peralatan pelindung seperti masker
debu, sepatu pengaman anti-selip, helm pengaman,
atau pelindung telinga yang digunakan untuk kondisi
yang sesuai akan mengurangi risiko cedera diri.
12. Cegah penyalaan yang tidak disengaja. Pastikan
bahwa sakelar berada dalam posisi mati (off)
sebelum menghubungkan mesin ke sumber daya
dan/atau baterai, mengangkat atau membawanya.
Membawa mesin listrik dengan jari Anda pada
sakelarnya atau mengalirkan listrik pada mesin listrik
yang sakelarnya hidup (on) akan mengundang
kecelakaan.
13.
Lepaskan kunci-kunci penyetel sebelum
menghidupkan mesin listrik. Kunci-kunci yang
masih terpasang pada bagian mesin listrik yang
berputar dapat menyebabkan cedera.
14. Jangan meraih terlalu jauh. Jagalah pijakan dan
keseimbangan sepanjang waktu. Hal ini
memungkinkan kendali yang lebih baik atas mesin
listrik dalam situasi yang tidak diharapkan.
15. Kenakan pakaian dengan baik. Jangan memakai
pakaian yang kedodoran atau perhiasan. Jaga
jarak antara rambut, pakaian, dan sarung tangan
Anda dengan bagian mesin yang bergerak.
Pakaian kedodoran, perhiasan, atau rambut panjang
dapat tersangkut pada bagian yang bergerak.
16. Jika tersedia fasilitas untuk menghisap dan
mengumpulkan debu, pastikan fasilitas tersebut
terhubung listrik dan digunakan dengan baik.
Penggunaan pembersih debu dapat mengurangi
bahaya yang terkait dengan debu.
Penggunaan dan pemeliharaan mesin listrik
17. Jangan memaksa mesin listrik. Gunakan mesin
listrik yang tepat untuk keperluan Anda. Mesin
listrik yang tepat akan menuntaskan pekerjaan
dengan lebih baik dan aman pada kecepatan sesuai
rancangannya.
18. Jangan gunakan mesin listrik jika sakelar tidak
dapat menyalakan dan mematikannya. Mesin listrik
yang tidak dapat dikendalikan dengan sakelarnya
adalah berbahaya dan harus diperbaiki.
19. Cabut steker dari sumber listrik dan/atau baterai
dari mesin listrik sebelum melakukan penyetelan,
penggantian aksesori, atau menyimpan mesin
listrik. Langkah keselamatan preventif tersebut
mengurangi risiko hidupnya mesin secara tak
sengaja.
20. Simpan mesin listrik jauh dari jangkauan anak-
anak dan jangan biarkan orang yang tidak paham
mengenai mesin listrik tersebut atau petunjuk ini
menggunakan mesin listrik. Mesin listrik sangat
berbahaya di tangan pengguna yang tak terlatih.
21. Rawatlah mesin listrik. Periksa apakah ada bagian
bergerak yang tidak lurus atau macet, bagian yang
pecah dan kondisi lain yang dapat mempengaruhi
penggunaan mesin listrik. Jika rusak, perbaiki
dahulu mesin listrik sebelum digunakan. Banyak
kecelakaan disebabkan oleh kurangnya pemeliharaan
mesin listrik.
22. Jaga agar mesin pemotong tetap tajam dan bersih.
Mesin pemotong yang terawat baik dengan mata
pemotong yang tajam tidak mudah macet dan lebih
mudah dikendalikan.
23. Gunakan mesin listrik, aksesori, dan mata mesin,
dll. sesuai dengan petunjuk ini, dengan
memperhitungkan kondisi kerja dan jenis
pekerjaan yang dilakukan. Penggunaan mesin listrik
untuk penggunaan yang lain dari peruntukan dapat
menimbulkan situasi berbahaya.
Penggunaan dan pemeliharaan mesin bertenaga
baterai
24. Isi ulang baterai hanya dengan pengisi daya yang
ditentukan oleh pabrikan. Pengisi daya yang cocok
untuk satu jenis baterai dapat menimbulkan risiko
kebakaran ketika digunakan untuk paket baterai yang
lain.
25. Gunakan mesin listrik hanya dengan baterai yang
telah ditentukan secara khusus. Penggunaan
baterai lain dapat menimbulkan risiko cedera dan
kebakaran.
12
26. Ketika baterai tidak digunakan, jauhkan dari
benda logam lain, seperti penjepit kertas, uang
logam, kunci, paku, sekrup atau benda logam kecil
lainnya, yang dapat menghubungkan satu
terminal ke terminal lain. Hubungan singkat terminal
baterai dapat menyebabkan luka bakar atau
kebakaran.
27. Pemakaian yang salah, dapat menyebabkan
keluarnya cairan dari baterai; hindari kontak. Jika
terjadi kontak secara tidak sengaja, bilas dengan
air. Jika cairan mengenai mata, cari bantuan
medis. Cairan yang keluar dari baterai bisa
menyebabkan iritasi atau luka bakar.
Servis
28. Berikan mesin listrik untuk diperbaiki hanya
kepada oleh teknisi yang berkualifikasi dengan
menggunakan hanya suku cadang pengganti yang
serupa. Hal ini akan menjamin terjaganya keamanan
mesin listrik.
29. Patuhi petunjuk pelumasan dan penggantian
aksesori.
30. Jagalah agar gagang kering, bersih, dan bebas
dari minyak dan gemuk.
GEB056-4
PERINGATAN KESELAMATAN
BOR OBENG GETAR
1. Kenakan pelindung telinga saat melakukan
pengeboran tumbuk (impact drilling). Terpaan
kebisingan dapat menyebabkan hilangnya
pendengaran.
2. Gunakan gagang tambahan, jika disertakan
bersama mesin ini. Kehilangan kendali dapat
menyebabkan cedera.
3. Pegang mesin listrik pada permukaan genggam
yang terisolasi saat melakukan pekerjaan bila
aksesori pemotong mungkin bersentuhan dengan
kawat tersembunyi. Aksesori pemotong yang
menyentuh kawat “hidup” dapat menyebabkan bagian
logam pada mesin teraliri arus listrik dan menyengat
pengguna.
4. Pegang mesin listrik pada permukaan genggam
yang terisolasi saat melakukan pekerjaan bila
pengencang mungkin bersentuhan dengan kawat
tersembunyi. Pengencang yang menyentuh kawat
“hidup” dapat menyebabkan bagian logam pada
mesin teraliri arus listrik dan menyengat pengguna.
5. Selalu pastikan Anda berada di atas alas yang
kuat.
Pastikan tidak ada orang di bawahnya bila Anda
menggunakan mesin di tempat yang tinggi.
6. Pegang mesin kuat-kuat.
7. Jauhkan tangan dari bagian yang berputar.
8. Jangan tinggalkan mesin dalam keadaan hidup.
Jalankan mesin hanya ketika digenggam tangan.
9. Jangan menyentuh mata mesin atau benda kerja
segera setelah pengoperasian; suhunya mungkin
masih sangat panas dan dapat membakar kulit
Anda.
10. Bahan tertentu mengandung zat kimia yang
mungkin beracun. Hindari menghirup debu dan
persentuhan dengan kulit. Ikuti data keselamatan
bahan dari pemasok.
SIMPAN PETUNJUK INI.
PERINGATAN:
JANGAN biarkan kenyamanan atau terbiasanya Anda
dengan produk (karena penggunaan berulang)
menggantikan kepatuhan yang ketat terhadap aturan
keselamatan untuk produk yang terkait.
PENYALAHGUNAAN atau kelalaian mematuhi kaidah
keselamatan yang tertera dalam petunjuk ini dapat
menyebabkan cedera badan serius.
ENC007-6
PETUNJUK KESELAMATAN
PENTING
UNTUK BATERAI
1. Sebelum menggunakan baterai, bacalah semua
petunjuk dan penandaan pada (1) pengisi daya
baterai, (2) baterai, dan (3) produk yang
menggunakan baterai.
2. Jangan membongkar baterai.
3. Jika waktu beroperasinya menjadi sangat singkat,
segera hentikan penggunaan. Hal tersebut dapat
menimbulkan risiko panas berlebih, kemungkinan
mengalami luka bakar atau bahkan terjadi ledakan.
4. Jika elektrolit mengenai mata Anda, basuh dengan
air bersih dan segera cari pertolongan medis. Hal
tersebut dapat mengakibatkan hilangnya
kemampuan penglihatan Anda.
5. Jangan menghubungkan terminal baterai:
(1) Jangan menyentuhkan terminal dengan
bahan penghantar listrik apapun.
(2) Hindari menyimpan baterai pada wadah yang
berisi benda logam lain seperti paku, uang
logam, dsb.
(3) Jangan membiarkan baterai terkena air atau
kehujanan.
Hubungan singkat baterai dapat menyebabkan
aliran arus listrik yang besar, panas berlebih,
kemungkinan mengalami luka bakar dan bahkan
kerusakan pada baterai.
6. Jangan menyimpan mesin dan baterai pada lokasi
dengan suhu yang bisa mencapai atau melebihi
50°C.
7. Jangan membuang baterai di tempat pembakaran
sampah walaupun benar-benar rusak atau tidak
bisa digunakan sama sekali. Baterai bisa meledak
jika terbakar.
8. Hati-hati jangan sampai baterai jatuh atau
terbentur.
9. Jangan menggunakan baterai yang rusak.
SIMPAN PETUNJUK INI.
Tip untuk menjaga agar umur pemakaian
baterai maksimum
1. Ganti baterai sebelum habis sama sekali.
Selalu hentikan penggunaan mesin dan ganti
baterai jika Anda melihat bahwa mesin kurang
tenaga.
13
2. Jangan pernah mengisi ulang baterai yang sudah
diisi penuh.
Pengisian ulang yang berlebih memperpendek
umur pemakaian baterai.
3. Isi ulang baterai pada suhu ruangan 10°C - 40°C.
Biarkan baterai yang panas menjadi dingin
terlebih dahulu sebelum diisi ulang.
DESKRIPSI FUNGSI
PERHATIAN:
•Selalu pastikan bahwa mesin dimatikan dan baterai
dilepas sebelum menyetel atau memeriksa kerja
mesin.
Memasang atau melepas baterai (Gb. 1)
•Selalu matikan mesin sebelum memasukkan atau
melepas baterai.
•Untuk melepas baterai, tarik dari mesin sambil
menggeser tombol pada bagian depan baterai.
•Untuk memasukkan baterai, sejajarkan lidah baterai
dengan alur pada rumah dan masukkan ke dalam
tempatnya. Selalu masukkan seluruhnya sampai
terkunci pada tempatnya dan terdengar bunyi klik kecil.
Jika Anda bisa melihat bagian berwarna merah pada
sisi atas tombol, berarti tidak terkunci sepenuhnya.
Masukkan sepenuhnya sampai bagian berwarna
merah tidak terlihat. Jika tidak, bisa terlepas dari mesin
secara tidak sengaja, menyebabkan luka pada Anda
atau orang di sekitar Anda.
•Jangan dipaksakan ketika memasukkan baterai. Jika
baterai tidak bergeser dengan mudah, berarti tidak
dimasukkan dengan benar.
Kerja saklar (Gb. 2)
PERHATIAN:
•Sebelum memasukkan baterai pada mesin, pastikan
picu saklar berfungsi dengan baik dan kembali ke
posisi “OFF” saat dilepas.
Untuk menjalankan mesin, cukup tarik picu saklarnya.
Kecepatan mesin akan meningkat dengan menambah
tekanan pada picu saklar. Lepaskan picu saklar untuk
berhenti.
Menyalakan lampu depan (Gb. 3)
PERHATIAN:
•Jangan melihat lampu atau sumber cahaya secara
langsung.
Tarik picu saklar untuk menyalakan lampu. Lampu tetap
menyala selama picu saklar ditarik. Lampu akan padam
sekitar 10 - 15 detik setelah melepas picu.
CATATAN:
•Gunakan kain kering untuk mengelap kotoran dari
lensa lampu. Hati-hati jangan sampai menggores lensa
lampu, atau hal tersebut dapat menurunkan tingkat
penerangannya.
Kerja saklar pembalik arah (Gb. 4)
Mesin ini memiliki saklar pembalik arah untuk mengubah
arah putaran. Tekan tuas saklar pembalik arah dari sisi A
untuk putaran searah jarum jam atau dari sisi B untuk
putaran berlawanan arah jarum jam.
Ketika tuas saklar pembalik arah pada posisi netral, picu
saklar tidak bisa ditarik.
PERHATIAN:
•Selalu periksa arah putaran sebelum penggunaan.
•Gunakan saklar pembalik arah hanya setelah mesin
benar-benar berhenti. Mengubah arah putaran
sebelum mesin berhenti dapat merusak mesin.
•Saat mesin tidak digunakan, selalu posisikan tuas
saklar pembalik arah pada posisi netral.
Perubahan kecepatan (Gb. 5)
Untuk mengubah kecepatan, pertama-tama matikan
mesin dan kemudian geser tuas pengubah kecepatan ke
sisi “2” untuk kecepatan tinggi atau “1” untuk kecepatan
rendah. Pastikan bahwa tuas pengubah kecepatan
diposisikan pada posisi yang tepat sebelum penggunaan.
Gunakan kecepatan yang tepat untuk pekerjaan Anda.
PERHATIAN:
•Selalu posisikan tuas pengubah kecepatan
sepenuhnya pada posisi yang tepat. Jika Anda
menggunakan mesin dengan tuas pengubah
kecepatan berada di posisi tengah antara sisi “1” dan
sisi “2”, mesin bisa rusak.
•Jangan menggunakan tuas pengubah kecepatan
ketika mesin sedang bekerja. Mesin bisa rusak.
Memilih mode kerja (Gb. 6)
Mesin ini menggunakan cincin pengubah mode kerja.
Pilih salahsatu dari tiga mode yang sesuai untuk
kebutuhan kerja Anda dengan menggunakan cincin ini.
Untuk putaran saja, putar cincin sehingga tanda panah
pada badan mesin mengarah ke tanda pada cincin.
Untuk putaran dengan getar, putar cincin sehingga tanda
panah mengarah ke tanda pada cincin.
Untuk putaran dengan kopeling, putar cincin sehingga
tanda panah mengarah ke tanda pada cincin.
PERHATIAN:
Selalu posisikan cincin dengan benar pada tanda
mode yang diinginkan. Jika Anda memakai mesin
dengan cincin berada di posisi tengah antara kedua
tanda mode alat bisa rusak.
Menyetel torsi pengencangan (Gb. 6)
Torsi pengencangan bisa disetel dalam 16 tahap dengan
memutar cincin penyetel sehingga skala tersebut
disejajarkan dengan tanda panah pada badan mesin.
Torsi pengencangannya minimum ketika angka 1
disejajarkan dengan tanda panah, dan maksimum ketika
angka 16 disejajarkan dengan tanda panah.
Sebelum penggunaan yang sebenarnya, pasang sekrup
percobaan pada bahan atau potongan bahan lain untuk
menentukan tingkat torsi yang dibutuhkan untuk
keperluan tertentu.
PERAKITAN
PERHATIAN:
•Selalu pastikan bahwa mesin dimatikan dan baterai
dilepas sebelum melakukan pekerjaan apapun pada
mesin.
14
Memasang atau melepas mata obeng atau
mata bor (Gb. 7)
Putar selongsong berlawanan arah jarum jam untuk
membuka rahang cekam. Masukkan mata bor ke dalam
cekam sejauh mungkin. Putar selongsong searah jarum
jam untuk mengencangkan cekam.
Untuk melepas mata mesin, putar selongsong
berlawanan arah jarum jam.
Memasang penahan mata mesin
(aksesori) (Gb. 8)
Pasang penahan mata mesin pada tonjolan di bagian
bawah mesin sisi sebelah kanan atau kiri dan kencangkan
dengan sekrup.
Ketika tidak menggunakan mata obeng, simpan dalam
penahan mata mesin. Mata mesin dengan panjang 45
mm bisa disimpan di situ.
Kait (Aksesori) (Gb. 9)
Kait bisa digunakan untuk menggantung mesin
sementara. Bisa dipasang pada salahsatu sisi mesin.
Untuk memasang kait, masukkan ke dalam alur pada
rumah mesin pada salah satu sisinya dan kemudian
kencangkan dengan sekrup. Untuk melepasnya,
kendurkan sekrup dan kemudian tarik keluar.
PENGGUNAAN
PERHATIAN:
•Selalu masukkan baterai seluruhnya sampai terkunci
pada tempatnya dan terdengar bunyi klik kecil. Jika
Anda bisa melihat bagian berwarna merah pada sisi
atas tombol, berarti tidak terkunci sepenuhnya.
Masukkan sepenuhnya sampai bagian berwarna
merah tidak terlihat. Jika tidak, bisa terlepas dari mesin
secara tidak sengaja, menyebabkan luka pada Anda
atau orang di sekitar Anda.
Pegang mesin kuat-kuat dengan satu tangan sementara
tangan yang lain pada bagian bawah baterai untuk
mengontrol gerak memutar.
Cara pengoperasian bor getar
PERHATIAN:
•Akan timbul gaya yang sangat kuat dan tiba-tiba pada
mesin/mata mesin saat menembus lubang, bila lubang
dipenuhi geram-geram atau partikel, atau bila
menabrak besi-besi tulangan yang terpasang di dalam
beton.
Pertama-tama, putar cincin pengubah mode kerja
sehingga tanda panah pada badan mesin mengarah pada
tanda . Cincin penyetel bisa disejajarkan pada tingkat
torsi manapun untuk pengoperasian ini.
Pastikan Anda menggunakan mata bor berujung
tungsten-carbide.
Posisikan mata mesin pada lokasi yang diinginkan untuk
membuat lubang, kemudian tarik picu saklarnya. Jangan
memaksa mesin listrik. Tekanan yang ringan akan
memberi hasil yang terbaik. Jaga posisi mesin dan cegah
agar tidak selip dari lubang.
Jangan menambah tekanan bila lubang dipenuhi geram-
geram atau partikel. Tetapi, nyalakan mesin tanpa
putaran, lalu angkat mata mesin sedikit dari lubang.
Dengan melakukan hal ini beberapa kali, lubang akan
besih dan pengeboran normal bisa dilanjutkan kembali.
Penghembus angin (pilihan aksesori)
(Gb. 10)
Setelah mengebor lubang, gunakan penghembus angin
untuk membersihkan lubang dari debu.
Pekerjaan pemasangan sekrup (Gb. 11)
Pertama-tama, putar cincin pengubah mode kerja
sehingga tanda panah pada badan mesin mengarah pada
tanda . Setel cincin penyetel pada tingkat torsi yang
tepat untuk pekerjaan Anda. Kemudian lakukan
sebagaimana berikut.
Posisikan ujung mata obeng pada kepala sekrup dan beri
tekanan pada mesin. Jalankan mesin dengan perlahan
dan kemudian tingkatkan kecepatan secara bertahap.
Lepas picu saklar segera setelah kopeling memotong.
PERHATIAN:
•Pastikan bahwa mata obeng dimasukkan lurus
terhadap kepala sekrup, atau sekrup dan/atau mata
bor bisa rusak.
CATATAN:
•Ketika memasang sekrup kayu, lakukan pengeboran
awal untuk membuat lubang pengarah agar
mempermudah pemasangan sekrup dan untuk
mencegah pecahnya benda kerja. Lihat tabel.
006421
Pekerjaan pengeboran
Pertama-tama, putar cincin penyetel sehingga penunjuk
mengarah pada tanda . Kemudian lakukan
sebagaimana berikut.
PERHATIAN:
•Menekan mesin secara berlebihan tidak akan
mempercepat pengeboran. Bahkan, tekanan yang
berlebihan hanya akan merusak mata bor Anda,
mengurangi kinerja mesin dan memperpendek usia
mesin.
Akan timbul gaya yang sangat kuat pada mesin/mata
bor saat menembus lubang. Pegang mesin dengan
kuat dan berhati-hatilah saat mata bor menembus
benda kerja.
Mata bor yang macet dapat dicabut dengan menyetel
saklar pembalik arah agar mesin berputar berlawanan
arah untuk mundur. Tetapi, mesin bisa saja mundur
mendadak jika Anda tidak memegangnya dengan kuat.
Diameter nominal sekrup
kayu (mm)
Ukuran lubang pengarah
yang dianjurkan (mm)
3,1 2,0 - 2,2
3,5 2,2 - 2,5
3,8 2,5 - 2,8
4,5 2,9 - 3,2
4,8 3,1 - 3,4
5,1 3,3 - 3,6
5,5 3,7 - 3,9
5,8 4,0 - 4,2
6,1 4,2 - 4,4
15
Tahan benda kerja berukuran kecil dengan penjepit
atau alat penahan lain.
•Jika mesin terus-menerus digunakan sampai baterai
habis, istirahatkan mesin selama 15 menit sebelum
melakukannya lagi dengan baterai yang penuh.
Mengebor kayu
Bila mengebor kayu, hasil terbaik didapat dengan mata
bor kayu yang dilengkapi sekrup pemandu. Sekrup
pemandu mempermudah pengeboran dengan menarik
mata bor ke dalam benda kerja.
Mengebor logam
Untuk mencegah mata bor selip ketika mulai membuat
lubang, buatlah takik dengan penitik lalu palu pada titik
yang akan dilubangi. Letakkan ujung mata bor pada takik
dan mulailah membor.
Gunakan cairan pendingin saat mengebor logam.
Pengecualian untuk besi dan kuningan yang harus dibor
kering.
PERAWATAN
PERHATIAN:
•Selalu pastikan bahwa mesin dimatikan dan baterai
dilepas sebelum melakukan pemeriksaan atau
perawatan.
•Jangan sekali-kali menggunakan bensin, tiner, alkohol,
atau bahan sejenisnya. Penggunaan bahan demikian
dapat menyebabkan perubahan warna, perubahan
bentuk atau timbulnya retakan.
Mengganti sikat karbon
Lepas ketika aus sampai tanda batas. Jaga agar sikat
karbon tetap bersih dan tidak bergeser dari tempatnya.
Kedua sikat karbon harus diganti pada waktu yang sama.
Hanya gunakan sikat karbon yang sama. (Gb. 12)
Gunakan obeng untuk melepas dua sekrup kemudian
lepas tutup belakang. (Gb. 13)
Angkat bagian lengan pegas dan tempatkan pada bagian
cekung rumah mesin dengan sebuah obeng bermata
celah dari poros kecil atau sejenisnya. (Gb. 14)
Gunakan tang untuk melepas tutup sikat karbon. Tarik
keluar sikat karbon yang aus, masukkan yang baru dan
pasang tutup tempat sikat dengan urutan terbalik.
(Gb. 15)
Pastikan bahwa tutup sikat karbon benar-benar terpasang
pada lubang tempat sikat. (Gb. 16)
Pasang lagi tutup belakang kemudian kencangkan
dengan dua sekrup.
Untuk menjaga KEAMANAN dan KEANDALAN mesin,
perbaikan, perawatan atau penyetelan lain harus
dilakukan oleh Pusat Layanan Resmi Makita dan selalu
gunakan suku cadang pengganti buatan Makita.
PILIHAN AKSESORI
PERHATIAN:
•Dianjurkan untuk menggunakan aksesori atau
perangkat tambahan ini dengan mesin Makita Anda
yang ditentukan dalam petunjuk ini. Penggunaan
aksesori atau perangkat tambahan lain bisa
menyebabkan risiko cedera pada manusia. Hanya
gunakan aksesori atau perangkat tambahan sesuai
dengan peruntukkannya.
Jika Anda memerlukan bantuan lebih rinci berkenaan
dengan aksesori ini, tanyakan pada Pusat Layanan
Makita terdekat.
•Mata bor
•Mata bor getar berujung tungsten-carbide
•Mata mesin Phillips
•Mata bor bercelah
•Mata soket
•Penghembus angin
•Kaca mata pelindung
•Macam-macam jenis baterai dan pengisi daya asli
buatan Makita.
•Kait
•Rakitan bantalan karet
Bonet wol
•Bantalan poles busa
CATATAN:
•Beberapa item dalam daftar tersebut mungkin sudah
termasuk dalam paket mesin sebagai aksesori standar.
Hal tersebut dapat berbeda dari satu negara ke negara
lainnya.
16
TING VIT
Gii thích v hình v tng th
THÔNG S K THUT
•Do chng trình nghiên cu và phát trin liên tc ca chúng tôi nên các thông s k thut trong ây có th thay i mà
không cn thông báo trc.
•Các thông s k thut và hp pin có th thay i tùy theo tng quc gia.
•Trng lng có hp pin tùy theo Quy trình EPTA tháng 01/2003
END004-4
Ký hiu
Phn di ây cho bit các ký hiu c dùng cho thit
b. m bo rng bn hiu rõ ý ngha ca các ký hiu này
trc khi s dng.
..... c tài liu hng dn.
ENE039-1
Mc ích s dng
Dng c này c thit k cho vic khoan óng vào gch,
bê-tông, á cng nh cho vic khoan không cn óng vào
g, kim loi, gm và nha.
GEA006-2
Cnh báo An toàn Chung dành
cho Dng c Máy
CNH BÁO! c tt c các cnh báo an toàn và
hng dn. Vic không tuân theo các cnh báo và
hng dn có th dn n in git, ho hon và/hoc
thng tích nghiêm trng.
Lu gi tt c cnh báo hng
dn  tham kho sau này.
Thut ng “dng c máy” trong các cnh báo  cp n
dng c máy (có dây) c vn hành bng ngun in
chính hoc dng c máy (không dây) c vn hành
bng pin ca bn.
An toàn ti ni làm vic
1. Gi ni làm vic sch s và có  ánh sáng. Ni
làm vic ba bn hoc ti thng d gây ra tai nn.
2. Không vn hành dng c máy trong môi tr
ng
cháy n, ví d nh môi trng có s hin din
ca các cht lng, khí hoc bi d cháy. Các dng
c máy to tia la in có th làm bi hoc khí bc
cháy.
3. Gi tr em và ngi ngoài tránh xa ni làm vic
khi ang vn hành dng c máy. S xao lãng th
khin bn mt kh nng kim soát.
An toàn v in
4. Phích c
m ca dng c máy phi khp vi cm.
Không bao gi c sa i phích cm theo bt
k cách nào. Không s dng bt k phích chuyn
i nào vi các dng c máy c ni t (tip
1. Phn màu 
2. Nút
3. Hp pin
4. Cn khi ng công tc
5. èn
6. Cn công tc o chiu
7. Cn thay i tc 
8. Vòng chuyn ch
 hot ng
9. Vòng iu chnh
10. Vòng chia 
11. Mi tên
12. Tr ngoài
13. Hp cha u mi
14. Mi vít
15. Rãnh
16. Vít
17. Móc treo
18. Bóng thi khí
19. Vch gii hn
20. Np sau
21. Phn hc rãnh
22. Lò xo
23. Tay cn
24. Np chi các-bon
25. L
KiuBHP442BHP452
Công sut
Bê-tông 13 mm
Thép 13 mm
G 38 mm
Vít bt g 6 mm x 75 mm 10 mm x 89 mm
Vít máy M6 M6
Tc  không ti (phút
-1
)
Cao (2) 0 - 1.400 0 - 1.500
Thp (1) 0 - 400 0 - 400
S nhát mi phút
Cao (2) 0 - 21.000 0 - 22.500
Thp (1) 0 - 6.000 0 - 6.000
Chiu dài tng th 215 mm 215 mm
Trng lng tnh 1,8 kg 1,7 kg
Hiu in th nh mc D.C. 14,4 V D.C. 18 V
17
t). Các phích cm còn nguyên vn và cm phù
hp s gim nguy c in git.
5. Tránh  c th tip xúc vi các b mt ni t
hoc tip t nh ng ng, b tn nhit, bp ga
và t lnh. Nguy c b in git s tng lên nu c
th bn c ni
t hoc tip t.
6. Không  dng c máy tip xúc vi ma hoc
trong iu kin m t. Nc lt vào dng c máy
s làm tng nguy c in git.
7. Không lm dng dây. Không bao gi s dng dây
 mang, kéo hoc tháo phích cm dng c máy.
Gi dây tránh xa ngun nhit, du, các mép sc
hoc các b phn chuyn ng.
Dây b hng hoc
b ri s làm tng nguy c in git.
8. Khi vn hành dng c máy ngoài tri, hãy s
dng dây kéo dài phù hp cho vic s dng ngoài
tri. Vic dùng dây phù hp cho vic s dng ngoài
tri s gim nguy c in git.
9. Nu bt buc phi vn hành dng c máy ni
m t, hãy s
dng ngun in b ngt mch
ni t khi rò in (GFCI). Vic s dng GFCI s
gim nguy c in git.
An toàn cá nhân
10. Luôn tnh táo, quan sát nhng vic bn ang làm
và s dng nhng phán oán theo kinh nghim
khi vn hành dng c máy. Không s dng dng
c máy khi bn ang mt mi hoc chu nh
hng c
a ma túy, ru hay thuc. Ch mt
khonh khc không tp trung khi ang vn hành dng
c máy cng có th dn n thng tích cá nhân
nghiêm trng.
11. S dng thit b bo h cá nhân. Luôn eo thit b
bo v mt. Các thit b bo h nh mt n chng
bi, giày an toàn chng trt, m bo h hay thit b
bo v thính giác c s dng trong các iu kin
thích hp s giúp gim thng tích cá nhân.
12. Tránh vô tình khi ng dng c máy. m bo
công tc v trí off (tt) trc khi ni ngun in
và/hoc b pin, cm hoc mang dng cy. Vic
mang dng c máy khi ang t ngón tay v trí công
tc hoc cp in cho dng c
máy ang bt thng
d gây ra tai nn.
13. Tháo mi khóa hoc chìa vn iu chnh trc khi
bt dng c máy. Vic chìa vn hoc khóa vn còn
gn vào b phn quay ca dng c máy có th dn
n thng tích cá nhân.
14. Không vi quá cao. Luôn gi thng bng tt
ch  chân phù hp. iu này cho phép iu khin
dng c máy t
t hn trong nhng tình hung bt ng.
15. n mc phù hp. Không mc qun áo rng hay
eo  trang sc. Gi tóc, qun áo và gng tay
tránh xa các b phn chuyn ng. Qun áo rng,
 trang sc hay tóc dài có th mc vào các b phn
chuyn ng.
16. Nu các thit b c cung cp  kt ni các thit
b thu gom và hút bi, hãy m bo chúng c
k
t ni và s dng hp lý. Vic s dng thit b thu
gom bi có th làm gim nhng mi nguy him liên
quan n bi.
S dng và bo qun dng c máy
17. Không dùng lc i vi dng c máy. S dng
úng dng c máy cho công vic ca bn. S
dng úng dng c máy s giúp thc hin công vic
t
t hn và an toàn hn theo giá tr nh mc c
thit k ca dng c máy ó.
18. Không s dng dng c máy nu công tc không
bt và tt c dng c máy ó. Mi dng c máy
không th iu khin c bng công tc u rt
nguy him và cn c sa cha.
19. Rút phích cm ra khi ngun i
n và/hoc ngt
kt ni b pin khi dng c máy trc khi thc
hin bt k công vic iu chnh, thay i ph
tùng hay ct gi dng c máy nào. Nhng bin
pháp an toàn phòng nga này s gim nguy c
tình khi ng dng c máy.
20. Ct gi các dng c máy không s dng ngoài
tm vi ca tr em không cho bt k ng
i nào
không có hiu bit v dng c máy hoc các
hng dn này vn hành dng c máy. Dng c
máy s rt nguy him nu c s dng bi nhng
ngi dùng cha qua ào to.
21. Bo qun dng c máy. Kim tra tình trng lch
trc hoc bó kp ca các b phn chuyn ng,
hin tng nt v c
a các b phn và mi tình
trng khác mà có th nh hng n hot ng
ca dng cy. Nu có hng hóc, hãy sa cha
dng c máy trc khi s dng. Nhiu tai nn xy
ra là do không bo qun tt dng c máy.
22. Luôn gi cho dng c ct c sc bén và sch
s. Nhng dng c ct c bo qun t
t có mép ct
sc s ít b kt hn và d iu khin hn.
23. S dng dng c máy, ph tùng và u dng c
ct, v.v... theo các hng dn này, tính n iu
kin làm vic công vic c thc hin. Vic s
dng dng c máy cho các công vic khác vi công
vic d nh có th gây nguy him.
S dng và b
o qun dng c dùng pin
24. Ch sc pin li vi b sc do nhà sn xut quy
nh. B sc phù hp vi mt loi b pin này có th
gây ra nguy c ha hon khi c dùng cho mt b
pin khác.
25. Ch s dng các dng cy vi các b pin c
quy nh c th. Vic s dng bt c b pin nào
khác có th gây ra thng tích và h
a hon.
26. Khi không s dng b pin, hãy gi tránh xac 
vt khác bng kim loi, chng hn nh kp giy,
tin xu, chìa khóa, inh, c vít hoc các vt nh
bng kim loi mà có th làm ni tt các u cc
pin. Các u cc pin b on mch có th gây cháy
hoc ha hon.
27. Trong iu kin s dng quá mc, pin có th b
chy nc; hãy tránh tip xúc. Nu vô tình tip
xúc vi pin b chy nc, hãy ra sch bng
nc. Nu dung dch t pin tip xúc vi mt, cn
i khám bác s thêm. Dung dch chy ra t pin có th
gây rát da hoc bng.
Bo dng
28.  nhân viên sa cha  trình  bo dng
dng c máy ca bn và ch s dng các b phn
thay th ng nht. Vic này s m bo duy trì
c  an toàn ca dng c máy.
29. Tuân theo hng dn dành cho vic bôi trn và
thay ph tùng.
30. Gi tay cm khô, sch, không dính du và m.
18
GEB056-4
CNH BÁO AN TOÀN I VI
MÁY KHOAN ÓNG BT VÍT
DÙNG PIN
1. eo thit b bo v tai khi khoan. Vic  tai tip xúc
vi ting n có th gây gim thính lc.
2. S dng các tay cm ph nu c cung cp kèm
theo dng c. Không iu khin c dng c s
gây ra thng tích cho con ngi.
3. Cm dng c máy bng b mt kp cách in khi
thc hin mt thao tác trong ó ph
kin ct có
th tip xúc vi dây dn kín. B phn ct tip xúc
vi dây dn “có in” có th khin các b phn kim
loi b h ca dng c máycó in” và làm cho ngi
vn hành b in git.
4. Cm dng c máy bng b mt kp cách in khi
thc hin mt thao tác trong ó b
phn kp có
th tip xúc vi dây dn in kín bên di. B
phn kp tip xúc vi dây dn “có in” có th khin
các b phn kim loi b h ca dng c máy “có in”
và làm cho ngi vn hành b in git.
5. Luôn chc chn rng bn có ch ta chân vng
chc.
m bo rng không có ai
di khi dùng dng
c nhng v trí trên cao.
6. Cm chc dng c.
7. Gi tay tránh xa các b phn quay.
8. Không  mc dng c hot ng. Ch vn hành
dng c khi cm trên tay.
9. Không chm vào mi khoan hay vt gia công ngay
sau khi vn hành; chúng có th rt nóng và có th
gây bng da.
10. Mt s vt liu có cha các hóa cht có th rt
c hi. Ph
i cn trng tránh hít phi bi và 
tip xúc vi da. Tuân theo các thông tin v an tn
ca nhà cung cp i vi mi loi vt liu.
LU GI CÁC HNG DN NÀY.
CNH BÁO:
KHÔNG c  s thoi mái hay quen thuc vi sn
phm (có c do s dng nhiu ln) thay th vic
tuân th nghiêm ngt các quy nh v an toàn dành
cho sn phm này. VIC DÙNG SAI hoc không tuân
theo các quy nh v an toàn c nêu trong tài liu
hng dn này có th dn n thng tích cá nhân
nghiêm trng.
ENC007-6
CÁC HNG DN AN TOÀN
QUAN TRNG
I VI HP PIN
1. Trc khi s dng hp pin, hãy c k tt c các
hng dn và du hiu cnh báo trên (1) b sc
pin, (2) pin và (3) sn phm s dng pin.
2. Không tháo ri hp pin.
3. Nu thi gian vn hành ngn hn nhiu, dng
vic vn hành ngay lp tc. iu này có th gây
nguy c quá nhit, gây cháy hoc thm chí gây
n.
4. Nu cht in phân dính vào m
t bn, hãy ra
sch bng nc sch và i khám bác s ngay lp
tc. Vic này có th làm gim th lc ca mt bn.
5. Không c on mch hp pin:
(1) Không c chm vào các u cc bng vt
liu dn in.
(2) Tránh ct gi hp pin trong ch cha có các
vt kim loi khác nh inh, tin xu, v.v...
(3) Không 
c  hp pin tip xúc vi nc
hoc ma.
Pin b on mch có th gây ra dòng in ln, gây
quá nhit, cháy và thm chí gây phóng in.
6. Không c ct gi dng c và hp pin nhng
ni nhit  có th vt quá 50°C.
7. Không c thiêu hy hp pin ngay c khi nó ã
b h hng nghiêm trng hoc hoàn toàn không
s dng c. H
p pin có th n khi b t cháy.
8. Cn thn không c làm ri hoc va p mnh
vào pin.
9. Không s dng pin ã h hng.
LU GI CÁC HNG DN NÀY.
Li khuyên  duy trì ti a tui th pin
1. Sc hp pin trc khi pin c x in hoàn toàn.
Luôn dng vic vn hành dng c và sc pin khi
bn nhn thy công sut dng c b gim.
2. Không bao gi sc li mt hp pin ã c sc
y.
Vic sc in thêm na s làm gim tui th pin.
3. Sc pin nhit  phòng t 10°C - 40°C.  pin
ang nóng ngu
i li dn trc khi sc pin.
MÔ T CHC NNG
CN TRNG:
•Luôn m bo rng ã tt dng c và tháo hp pin ra
trc khi thc hin vic iu chnh hoc kim tra chc
nng trên dng c.
Lp hoc tháo g hp pin (Hình 1)
•Luôn tt dng c trc khi lp hoc tháo hp pin.
 tháo hp pin, hãy rút nó ra t dng c trong lúc
trt nút bên hông hp pin.
 lp hp pin vào, hãy canh chnh phn cht ca hp
pin vào phn rãnh nm trên v và trt cht vào v trí.
Luôn trt ht mc n khi nào cht khóa úng vào v
trí vi mt ting click nh. Nu bn vn còn nhìn thy
phn màu  phía trên nút b
m, cht vn cha c
khóa hoàn toàn. Lp cht hoàn toàn vào v trí cho n
khi không th nhìn thy phn màu . Nu không, cht
có th vô tình ri ra khi dng c, gây thng tích cho
bn hoc ngi khác xung quanh.
•Không c n mnh khi lp hp pin. Nu hp pin
không nh nhàng trt vào v trí, có ngha là pin vn
cha c lp úng.
19
Hot ng công tc (Hình 2)
CN TRNG:
•Trc khi lp hp pin vào dng c, luôn luôn kim tra
xem cn khi ng công tc có hot ng bình thng
hay không và tr v v trí “OFF” (TT) khi nh ra.
 khi ng dng c, ch cn kéo cn khi ng công
tc. Tc  dng c c gim xung bng cách tng lc
ép lên cn khi ng công tc. Nh cn kh
i ng công
tc ra  dng.
Bt èn trc (Hình 3)
CN TRNG:
ng nhìn thng trc tip vào èn hoc ngun sáng.
Kéo cn khi ng công tc  bt sáng èn. èn s vn
sáng trong lúc cn khi ng công tc ang c kéo.
èn s tt t 10 - 15 giây sau khi nh cn khi ng.
LU Ý:
•Dùng vi khô  lau bi bn trên kính èn. Cn thn
không c làm xc kính èn, nu không èn có th
b gim  sáng.
Hot ng công tc o chiu (Hình 4)
Dng c này có mt công tc o chiu  thay i chiu
xoay. Nhn nút công tc o chiu t mt A  xoay theo
chiu kim ng h hoc t mt B  xoay ngc chiu
kim ng h.
Khi nút công tc o chiu v trí chính gia, không th
kéo cn khi ng công tc c.
CN TRNG:
•Luôn luôn kim tra hng xoay trc khi vn hành.
•Ch s
dng công tc o chiu sau khi dng c ã
dng hoàn toàn. Vic thay i hng xoay trc khi
dng c dng có th làm hng dng c.
•Khi vn hành dng c, luôn t nút công tc o chiu
v trí chính gia.
Thay i tc  (Hình 5)
 thay i tc , u tiên hãy tt dng c và trt cn
thay i tc  sang v trí “2 có tc  cao hoc v trí
“1”  có tc  thp. m bo rng cn thay i tc 
c t úng v trí trc khi vn hành. S dng úng
tc  cho công vic ca bn.
CN TRNG:
•Luôn  c
n thay i tc  vào tht úng v trí. Nu
bn vn hành dng c vi cn thay i tc  t
mt na gia v trí “1” và “2”, dng c có th b h
hng.
•Không c s dng cn thay i tc  trong lúc
dng c ang chy. Dng c có th b h hng.
Chn ch  hot ng (Hình 6)
Dng c này có th tn dng vòng chuyn ch  hot
ng. Chn mt trong ba ch  phù hp vi nhu cu
công vic ca bn bng vòng này.
 vào ch  ch khoan, hãy xoay vòng sao cho mi tên
trên thân dng c ch n du hiu trên vòng.
 khoan óng búa, hãy xoay vòng sao cho mi tên ch
n du hiu trên vòng.
 vào ch  xoay có ly hp, hãy xoay vòng sao cho mi
tên ch n du hiu trên vòng.
CN TRNG:
•Luôn luôn chnh vòng này vào úng du hiu ca ch
 mà bn mun. Nu bn vn hành dng c này vi
vòng chuyn ch  hot ng c t gia các
du hiu, dng c có th b h hng.
iu chnh lc vn xit (Hình 6)
Lc vn xit có th c iu chnh theo 16 nc bng
cách xoay vòng iu chnh  canh chnh các  chia theo
mi tên trên thân dng c. Lc vn xit t ti thiu khi s
1 c cn chnh vào mi tên t ti a khi s 16 c
cn chnh vào mi tên.
Trc khi vn hành thc t, hãy bt th mt c vít vào vt
li
u hoc mu vt liu tng t c nh mc lc xon
nào cn cho ng dng c th ó.
LP RÁP
CN TRNG:
•Luôn m bo rng ã tt dng c và tháo hp pin ra
trc khi thc hin bt c thao tác nào trên dng c.
Lp t hoc tháo mi vn hoc mi
khoan (Hình 7)
Xoay tr ngoài ngc chiu kim ng h  m các mu
ngàm kp. t u mi vào trong ngàm kp ht mc có
th. Xoay tr ngoài theo chiu kim ng h  vn cht
ngàm kp.
 tháo u mi, xoay tr ngoài ngc chiu kim ng
h.
Lp t hp cha u mi (ph kin)
(Hình 8)
Lp va khít hp cha u mi vào phn nhô ra chân
dng c c bên phi hoc trái và vn cht bng vít.
Khi không s dng u mi vít, hãy gi nó trong hp
cha u mi. Có th cha các mi vít dài 45 mm trong
hp.
Móc treo (Ph kin) (Hình 9)
Móc treo rt thun tin cho vic treo tm dng c. Móc
treo có th c lp c hai bên ca dng c.
 lp t móc treo, lp nó vào rãnh trên v dng c trên
bt c mt nào và sau ó xit cht li bng vít.  tháo
ra, vn lng vít ri ly móc treo ra.
VN HÀNH
CN TRNG:
•Luôn luôn lp hp pin vào ht mc cho n khi nó khóa
úng vào v trí. Nu bn vn còn nhìn thy phn màu
 phía trên nút bm, cht vn cha c khóa hoàn
toàn. Lp cht hoàn toàn vào v trí cho n khi không
th nhìn thy phn màu . Nu không, cht có th
tình ri ra khi dng c, gây thng tích cho bn hoc
ngi khác xung quanh.
Gi dng c tht cht bng mt tay trên tay cm và tay
kia trên phn áy hp pin  kim soát thao tác vn xon.
20
Thao tác khoan búa
CN TRNG:
•S có lc xon rt ln và bt ng trên dng c/mi
khoan lúc l khoan c xuyên thng, khi l khoan bt
u b kt bi các mt vn và ht hoc khi ng vào
các thép gia cng có trong bê-tông.
u tiên, xoay vòng thay i ch  hot ng sao cho
mi tên trên thân máy ch vào du . Vòng iu chnh có
th c cn chnh theo bt c cp  l
c vn nào cho
thao tác này.
m bo rng bn s dng mi khoan có u bt
tungsten-cacbua.
nh v u mi vào v trí mong mun cho l khoan, sau
ó kéo cn khi ng công tc. Không dùng lc i vi
dng c máy. n nh s mang li kt qu tt nht. Gi
cho dng c úng v trí và ngn không b trt khi l
khoan.
Không c
n mnh khi l khoan bt u b nghn bi
các mt vn và các ht. Thay vào ó, hãy chy dng c
ch  ch, sau ó tháo riêng mi khoan khi l. Bng
cách lp li thao tác này vài ln, l khoan s c sch
s và có th tip tc khoan bình thng.
Bóng thi khí (ph kin tùy chn)
(Hình 10)
Sau khi khoan l, s dng bóng thi khí  v sinh bi
bn ra khi l.
Thao tác bn vít (Hình 11)
u tiên, xoay vòng thay i ch  hot ng sao cho
mi tên trên thân máy cho du . Chnh nút iu chnh
n cp  lc vn phù hp vi công vic ca bn. Sau
ó tin hành nh sau.
t nh mi vn vào trong u vít và nhn dng c. Khi
ng dng c t t, sau ó tng tc  dn dn. Nh cn
khi 
ng công tc ngay khi b ly hp va ngt.
CN TRNG:
m bo rng mi vn c lp thng ng vào u
vít, nu không vít và/hoc mi vn có th b h hng.
LU Ý:
•Khi vn các vít bt g, hãy khoan trc các l nh
hng  giúp bt vít d dàng hn và ngn vt gia
công b chia tách. Xem s .
006421
Thao tác khoan
u tiên, xoay vòng iu chnh sao cho vch chun ch
vào du . Sau ó tin hành nh sau.
CN TRNG:
•Nhn dng c quá mc s không tng tc  khoann
c. Trên thc t, vic nhn mnh thêm này s ch
làm gây hng u mi ca bn, gim hiu nng và tui
th hot ng ca dng c.
•S có lc quán tính rt l
n trên dng c/mi khoan lúc
l khoan c xuyên thng. Gi cht dng c
chun b ghìm lc quán tính li khi mi khoan xuyên
thng vt gia công.
•Mi khoan b kt có th c tháo ra n gin bng
cách t công tc o chiu sang ch  xoay ngc
li  rút mi khoan ra. Tuy nhiên, dng c th quay
ngc ra bt ng nu bn không gi cht.
•Luôn luôn gi ch
t các vt gia công có kích thc nh
bng kìm hoc dng c kp tng t.
•Nu dng c c vn hành liên tc cho n khi hp
pin ã b x kit, hãy  dng c ngh 15 phút trc khi
thc hin tip bng pin mi.
Khoan vào g
Khi khoan vào g,  có kt qu tt nht cn s dng các
mi khoan dùng  khoan g và vít dn. Vít d
n giúp
khoan d dàng hn bng cách kéo u mi vào trong vt
gia công.
Khoan vào kim loi
 phòng nga u mi b trt ra lúc bt u khoan l,
hãy to mt vt lõm bng cách dùng dùi c tâm và óng
vào im cn khoan. t u mi khoan vào ch lõm này
và bt u khoan.
S dng du nhn  ct khi khoan kim loi. Tr các
trng hp dùng st và ng thau cn phi c khoan
khô.
BO TRÌ
CN TRNG:
•Hãy luôn chc chn rng dng c ã c tt và hp
pin ã c tháo ra trc khi c gng thc hin vic
kim tra hay bo dng.
•Không bao gi dùng xng, ét xng, dung môi, cn
hoc hóa cht tng t. Có th xy ra hin tng mt
màu, bin dng hoc nt v.
Thay th các chi các-bon
Thay th khi chi ã mòn n vch gii hn. Hãy gi cho
các chi các-bon sch s và không qun vào trong các
u gi. Các chi các-bon nên c thay th cùng lúc.
Hãy s dng các chi các-bon ging nhau. (Hình 12)
Dùng tuc-n-vít  tháo hai con c, sau ó tháo np sau
ra. (Hình 13)
Nhc phn tay cn ca lò xo ri sau ó t nó vào phn
hc rãnh ca v bng tuc-n-vít có u rãnh tit din
nh ho
c dng c tng t. (Hình 14)
Dùng kìm  tháo các np chi các-bon trên các chi các-
bon. Hãy tháo các chi các-bon ã b mòn, lp vào các
chi mi và vn cht li các np chi các-bon theo chiu
ngc li. (Hình 15)
m bo rng các np chi các-bon va khít vào các l
trong b phn gi chi tht cht. (Hình 16)
Lp t li np sau và vn cht hai con c.
ng kính danh nh
ca vít b
t g (mm)
Kích thc khuyn cáo
ca l khoan dn (mm)
3,1 2,0 - 2,2
3,5 2,2 - 2,5
3,8 2,5 - 2,8
4,5 2,9 - 3,2
4,8 3,1 - 3,4
5,1 3,3 - 3,6
5,5 3,7 - 3,9
5,8 4,0 - 4,2
6,1 4,2 - 4,4
1 / 1

Makita BHP442 User manual

Category
Power drills
Type
User manual
This manual is also suitable for

Ask a question and I''ll find the answer in the document

Finding information in a document is now easier with AI

Ask the document