Ferm AGM1043 User manual

Category
Angle grinders
Type
User manual
EN
DE
NL
FR
ES
PT
IT
SV
FI
NO
DA
HU
CS
SK
SL
PL
LT
LV
ET
RO
HR
SR
RU
UK
EL
ANGLE GRINDER
880W - 125MM
AGM1043
WWW.FERM.COM
PL
Original instructions 05
Übersetzung der Originalbetriebsanleitung 09
Vertaling van de oorspronkelijke gebruiksaanwijzing
13
Traduction de la notice originale 17
Traducción del manual original 21
Tradução do manual original 25
Traduzione delle istruzioni originali 29
Översättning av bruksanvisning i original 33
Alkuperäisten ohjeiden käännös 37
Oversatt fra orginal veiledning 41
Oversættelse af den originale brugsanvisning 44
Eredeti használati utasítás fordítása 48
 
Prevod izvirnih navodil 56
 
 
Originalios instrukcijos vertimas 67
 
Algupärase kasutusjuhendi tõlge 74
 
Prevedeno s izvornih uputa 82
Prevod originalnog uputstva 86
 
 

99
5
EN
ANGLE GRINDER
AGM1043
Thank you for buying this Ferm product.
By doing so you now have an excellent product,
delivered by one of Europe’s leading suppliers.
All products delivered to you by Ferm are
manufactured according to the highest standards
of performance and safety. As part of our
philosophy we also provide an excellent customer
service, backed by our comprehensive warranty.
We hope you will enjoy using this product for
many years to come.
SAFETY WARNINGS
1
WARNING
Read the enclosed safety warnings,
the additional safety warnings and
the instructions.
Failure to follow the safety warnings and
the instructions may result in electric
shock, re and/or serious injury.
Keep the safety warnings and the
instructions for future reference.
The following symbols are used in the user
manual or on the product:
1
Read the user manual.
2
Risk of personal injury.
3
Risk of electric shock.
4
Immediately remove the mains plug from
the mains if the mains cable becomes
damaged and during cleaning and
maintenance.
6
Risk of ying objects. Keep bystanders
away from the work area.
5
Wear safety goggles. Wear hearing
protection.
I
Wear safety gloves.
J
Do not press the spindle lock button
while the motor is running.
K
Risk of re.
8
Do not dispose of the product in
unsuitable containers.
9
The product is in accordance with the
applicable safety standards in the
European directives.
ADDITIONAL SAFETY WARNINGS FOR
ANGLE GRINDERS
● Themachinehasbeendesignedforuseasa
grinder or cut-off machine. The machine is not
suitable for operations such as sanding, wire
brushing, polishing, etc. Risk of personal injury.
● Donotuseaccessorieswhicharenot
specicallydesignedandrecommendedby
the manufacturer. Risk of personal injury.
● Inspectthemachineandtheaccessories
beforeeachuse.Donotuseaccessories
which are bent, cracked, or otherwise
damaged.Ifthemachineoroneofthe
accessories is dropped, inspect the machine
ortheaccessoryfordamage.Ifnecessary,
replace the accessory.
● Letthemachinerunatnoloadinasafearea
aftermountingtheaccessories.Ifthemachine
vibrates strongly, immediately switch off the
machine, remove the mains plug from the
mains, and try to solve the problem.
● Makesurethatthemaximumspeedforthe
grinding disc is larger than or the same as the
maximum speed of the machine. Refer to the
rating plate on the machine.
● Onlyusegrindingdiscswiththecorrect
thickness and outside diameter. Refer to the
rating plate on the machine.
● Makesurethatspindlediameterofgrinding
discs, spacers, tension nuts, etc. correspond
to the diameter of the spindle on the machine.
● Makesurethatthegrindingdiscisproperly
mounted.Donotuseadaptersorotheraidsto
mount grinding discs with another spindle
diameter.
● Onlyusegrindingdiscsthatarerecommended
bythemanufacturer.Onlyuseguardsthatare
specicallydesignedforthegrindingdisc.
● Onlyusegrindingdiscsthataresuitablefor
the application. For example: do not grind with
the side of a cut-off disc.
● Donotusethemachinewithouttheguard.
Securely mount the guard for maximum safety.
6
EN
Makesurethattheuserisprotectedfromthe
grinding disc as much as possible.
● Makesurethattheworkpieceisproperly
supportedorxed.
● Wearsafetygoggles.Wearhearingprotection.
Wearadustmask.Ifnecessary,useother
protective means, such as safety gloves,
safety shoes, etc. Risk of personal injury.
● Keepbystandersawayfromtheworkarea.
Makesurethatallpersonsintheworkarea
wear protective equipment. Risk of personal
injury.
● Keepthemainscableawayfromtherotating
grindingdisc.Ifthemainscabletouchesthe
rotating grinding disc, your hands or arms may
come in contact with the grinding disc.
Risk of personal injury.
● Holdthemachinebytheinsulatedgripping
surfaces where the grinding disc may contact
hiddenwiringorthemainscable.Ifthe
grinding disc contacts a ‘live’ wire, the exposed
metal parts of the machine can also become
‘live’. Risk of electric shock.
● Donotusethemachinewhilecarryingitat
your side. Risk of personal injury.
● Donotusethemachineonworkpieces
requiring a maximum grinding depth that
exceeds the maximum grinding depth of the
grinding disc.
● Donotuseaccessoriesthatrequireliquid
coolants. Risk of electric shock.
● Donotusethemachinenearammable
materials.Riskofre.
● Donotworkmaterialscontainingasbestos.
Asbestos is considered carcinogenic.
● Donotworkmetalwithamagnesiumcontent
of more than 80%.
● Bewarethatthegrindingdisccontinuesto
rotate for a short period after switching off the
machine.Donotattempttobringthegrinding
disc to a standstill yourself.
● Neverputthemachinedownonatableora
workbench before it has been switched off.
● Regularlycleantheventilationslots.Riskof
electric shock.
Kickbackisasuddenreactiontoapinched,
bound or twisted grinding disc, which causes the
machine to lift up and out of the workpiece towards
theuser.Ifthegrindingdiscispinchedorbound
tightly by the cut, the grinding disc jams and the
machine is rapidly driven back towards the user.
Ifthegrindingdiscistwistedinthe
cut,theback
edge of the grinding disc can dig into the top
surface of the workpiece, which causes the
grinding disc to climb out of the cut and jump
back towards the user.
Kickbackistheresultofincorrectuseofthe
machine and/or incorrect operating procedures or
conditions.Kickbackcanbeavoidedbytaking
proper precautions:
● Firmlyholdthemachinewithbothhands.
Position your arms to resist kickback forces.
Position your body to either side of the grinding
disc, but not in line with the grinding disc.
Kickbackcancausethegrindingdisctojump
backwards.Ifproperprecautionsaretaken,
kickback forces can be controlled by the user.
● Beextracarefulwhenusingthemachineon
corners,sharpedges,etc.Makesurethatthe
grinding disc does not become jammed.
Risk of kickback.
● Ifthegrindingdiscjamsorifyouinterruptacut
for any reason, release the on/off switch and
hold the machine motionless in the material
until the grinding disc comes to a complete
standstill. Never attempt to remove the
machine from the workpiece or pull the
machine backward while the grinding disc is in
motion. Risk of kickback.
● Donotusebluntordamagedgrindingdiscs.
Unsharpened or incorrectly mounted grinding
discs produce narrow cuts, which causes
excessive friction and kickback and increases
the risk of the grinding discs becoming
jammed.
● Donotusetoothedsawblades.Donotuse
woodcarving blades for saw chains. Risk of
personal injury.
ELECTRICAL SAFETY
3
Always check that the voltage of the
power supply corresponds to the voltage
on the rating plate.
● Donotusethemachineifthemainscableor
the mains plug is damaged.
● Onlyuseextensioncablesthataresuitablefor
the power rating of the machine with a
minimum thickness of 1.5 mm
2
.Ifyouusea
extension cable reel, always fully unroll the
cable.
7
EN

Ifthemoulded3-pinplugattachedtotheunitis
damaged and needs replacing, it is important that
it is correctly destroyed and replaced by an
approvedBS1363/5Afusedplugandthatthe
following wiring instructions are followed.
The wires in the mains cable are coloured in
accordance with the following code:
blue neutral
brown live
As the colours of the wires in the mains cable of
the unit may not correspond to the coloured
markings identifying the terminals in the plug,
proceed as follows:
- The wire which is coloured blue must be
connected to the terminal which is marked with
the letter N or coloured black.
- The wire which is coloured brown must be
connected to the terminal which is marked with
theletterLorcolouredred.
TECHNICAL DATA
AGM1043
Mainsvoltage V~ 230
Mainsfrequency Hz 50
Power input W 880
No-load speed min
-1
11,000
Grinding disc
Diameter mm 125
Bore mm 22.2
Spindlethread M14
Weight kg 2.2
NOISE AND VIBRATION
AGM1043
Soundpressure(L
pa
) dB(A) 87.7
Acousticpower(L
wa
) dB(A) 98.7
Uncertainty(K) dB(A) 3
Vibration m/s
2
7.52
Uncertainty(K) m/s
2
1.5
2
Wear hearing protection.
Vibration level
The vibration emission level stated in this instruction
manual has been measured in accordance with a
standardisedtestgiveninEN60745;itmaybeused
to compare one tool with another and as a
preliminary assessment of exposure to vibration
when using the tool for the applications mentioned
- using the tool for different applications, or with
different or poorly maintainted accessories,
maysignicantlyincreasetheexposurelevel
- the times when the tool is switched off or when
it is running but not actually doing the job, may
signicantlyreducetheexposurelevel
Protect yourself against the effects of vibration by
maintaining the tool and its accessories, keeping
yourhandswarm,andorganizingyourwork
patterns

Your angle grinder has been designed for grinding
and cutting masonry and steel.
1. On/offswitch
2. On/offswitchlock
3. Spindlelockbutton
4. Spindle
5. Guard
6. Maingrip
7. Auxiliary grip
8. Carbon brush indicator
ASSEMBLY
4
Before assembly, always switch off the
machine and remove the mains plug
from the mains.
Mounting and removing the grinding disc

2
Never attempt to remove the guard.
Mounting
● Placethemachineonatablewiththeguard
(5) facing upwards.
● Mountthespacer(9)ontothespindle(4).
● Mountthegrindingdisc(10)ontothespindle(4).
● Keepthespindlelockbutton(3)pressedand
rmlytightenthetensionnut(11)usingthe
spanner (12).
Removing
● Placethemachineonatablewiththeguard
(5) facing upwards.
● Keepthespindlelockbutton(3)pressedand
loosen the tension nut (11) using the spanner
(12).
● Removethegrindingdisc(10)fromthespindle
(4).
8
EN
● Keepthespindlelockbutton(3)pressedand
rmlytightenthetensionnut(11)usingthe
spanner (12).

● Tightentheauxiliarygrip(7)intooneofthe
mountingholes(13).
USE

Toswitchonthemachineincontinuousmode,
slide the on/off switch lock (2) to the right and
slide the on/off switch (1) in the direction of the
grindingdisc(g.D1).
Toswitchoffthemachine,pressthelowerpart
oftheon/offswitch(1)(g.D2).
Hints for optimum use
● Clamptheworkpiece.Useaclampingdevice
for small workpieces.
● Drawalinetodenethedirectioninwhichto
guide the grinding disc.
● Holdthemachinewithbothhands.
● Switchonthemachine.
● Waituntilthemachinehasreachedfullspeed.
● Placethegrindingdiscontheworkpiece.
● Slowlymovethemachinealongthepre-drawn
line,rmlypressingthegrindingdiscagainst
the workpiece.
● Donotapplytoomuchpressureonthe
machine.Letthemachinedothework.
● Switchoffthemachineandwaitforthe
machine to come to a complete standstill
before putting the machine down.
CLEANING AND MAINTENANCE
4
Before cleaning and maintenance,
always switch off the machine and
remove the mains plug from the mains.
● Regularlycleanthehousingwithasoftcloth.
● Keeptheventilationslotsfreefromdustand
dirt.Ifnecessary,useasoft,moistclothto
remove dust and dirt from the ventilation slots.

Ifthecarbonbrushesareworn,thecarbonbrush
indicator (8) will come on. The carbon brushes
must be replaced by the customer service
department of the manufacturer or a similarly
qualiedperson.
WARRANTY
Consult the enclosed warranty terms.
ENVIRONMENT
Disposal
8
The product, the accessories, and the packaging
must be sorted for environmentally friendly
recycling.

Donotdisposeofpowertoolsintodomestic
waste. According to the European Guideline
2002/96/EC for Waste Electrical and Electronic
Equipment and its implementation into national
right, power tools that are no longer usable must
be collected separately and disposed of in an
environmentally friendly way.
The product and the user manual are subject to
change.Specicationscanbechangedwithout
further notice.
106
Spare parts list
No. Description Position
409896 Outerange 1
409897 Innerange 3
409898 Clampingsetforguard 4+5
409910 Wheelguard 6
409899 Springring 7
409900 Spindle 8
409901 Frontcap 13
409902 Gearwheel 17
409903 Spindlelock 23+24
806000 Bearing6000ZZ 26
409904 Pineongear 28
409905 Rotor 29
800607 Bearing607ZZ 30
409906 Stator 34
409907 Switchcomplete 37til40
409908 Carbonbrushset 53
409909 Carbonbrushholder 54
406814 Camwrench 56
400973 Sidehandgrip 57
www.ferm.com
1201-05
WWW.FERM.COM
1201-05
  • Page 1 1
  • Page 2 2
  • Page 3 3
  • Page 4 4
  • Page 5 5
  • Page 6 6
  • Page 7 7
  • Page 8 8
  • Page 9 9
  • Page 10 10
  • Page 11 11
  • Page 12 12
  • Page 13 13
  • Page 14 14
  • Page 15 15
  • Page 16 16
  • Page 17 17
  • Page 18 18
  • Page 19 19
  • Page 20 20
  • Page 21 21
  • Page 22 22
  • Page 23 23
  • Page 24 24
  • Page 25 25
  • Page 26 26
  • Page 27 27
  • Page 28 28
  • Page 29 29
  • Page 30 30
  • Page 31 31
  • Page 32 32
  • Page 33 33
  • Page 34 34
  • Page 35 35
  • Page 36 36
  • Page 37 37
  • Page 38 38
  • Page 39 39
  • Page 40 40
  • Page 41 41
  • Page 42 42
  • Page 43 43
  • Page 44 44
  • Page 45 45
  • Page 46 46
  • Page 47 47
  • Page 48 48
  • Page 49 49
  • Page 50 50
  • Page 51 51
  • Page 52 52
  • Page 53 53
  • Page 54 54
  • Page 55 55
  • Page 56 56
  • Page 57 57
  • Page 58 58
  • Page 59 59
  • Page 60 60
  • Page 61 61
  • Page 62 62
  • Page 63 63
  • Page 64 64
  • Page 65 65
  • Page 66 66
  • Page 67 67
  • Page 68 68
  • Page 69 69
  • Page 70 70
  • Page 71 71
  • Page 72 72
  • Page 73 73
  • Page 74 74
  • Page 75 75
  • Page 76 76
  • Page 77 77
  • Page 78 78
  • Page 79 79
  • Page 80 80
  • Page 81 81
  • Page 82 82
  • Page 83 83
  • Page 84 84
  • Page 85 85
  • Page 86 86
  • Page 87 87
  • Page 88 88
  • Page 89 89
  • Page 90 90
  • Page 91 91
  • Page 92 92
  • Page 93 93
  • Page 94 94
  • Page 95 95
  • Page 96 96
  • Page 97 97
  • Page 98 98
  • Page 99 99
  • Page 100 100
  • Page 101 101
  • Page 102 102
  • Page 103 103
  • Page 104 104
  • Page 105 105
  • Page 106 106
  • Page 107 107
  • Page 108 108
  • Page 109 109

Ferm AGM1043 User manual

Category
Angle grinders
Type
User manual

Ask a question and I''ll find the answer in the document

Finding information in a document is now easier with AI