GEAR PULLER - THREE JAW
Model
08832
Distributed Exclusively by Harbor Freight Tools
®
.
3491 Mission Oaks Blvd., Camarillo, CA 93011
Visit our Web site at http://www.harborfreight.com
Copyright
©
2007 by Harbor Freight Tools. All rights reserved. No portion of this instruction sheet or any artwork
contained herein may be reproduced in any shape or form without the express written consent of Harbor Freight
Tools.
For technical questions please call 1-800-444-3353
Size Maximum Pulling Force
3” > 2.5 Ton
4” > 2.5 Ton
6” > 3.5 Ton
SAVE THIS INSTRUCTION SHEET
Keep this instruction sheet for the safety warnings and precautions, assembly, operating, inspec-
tion, maintenance and cleaning procedures. Keep this instruction sheet and the receipt in a safe and
dry place for future reference.
UNPACKING
When unpacking, check to make sure all parts shown on the photo are included. If any parts
are missing or broken, please call Harbor Freight Tools at the number shown on the front page of this
instruction sheet as soon as possible.
GENERAL SAFETY WARNINGS AND PRECAUTIONS
DO NOT USE THIS PRODUCT IF UNDER THE INFLUENCE OF ALCOHOL OR DRUGS. Read
warning labels on prescriptions to determine if your judgment or reexes are impaired while taking
drugs. If there is any doubt, do not attempt to use this product.
USE EYE PROTECTION. Wear ANSI approved safety impact eye glasses when using this
product. ANSI approved safety impact eye glasses are available from Harbor Freight Tools.
DRESS SAFELY. Non-skid footwear or safety shoes should be used when working with this
product. Do not wear loose clothing or jewelry as they can become caught in moving parts. Wear
1.
2.
3.
Page 2SKU 08832 For technical questions, please call 1-800-444-3353.
a protective hair covering to prevent long hair from becoming caught in moving parts. If wearing a
long-sleeve shirt, roll sleeves up above elbows.
CHECK FOR DAMAGED PARTS. Before using this product, carefully check that it will
operate properly and perform its intended function. Check for damaged parts and any other
conditions that may affect the operation of this product. Replace or repair damaged or worn
parts immediately. When servicing, use only identical replacement parts. Only use accessories
intended for use with this product. Approved accessories are available from Harbor Freight Tools.
MAINTENANCE: For your safety, service and maintenance should be performed regularly by a
qualied technician.
USE THE RIGHT PRODUCT FOR THE RIGHT JOB. There are certain applications for which
this product was designed. Do not use small equipment, tools or attachments to do the work of
larger industrial equipment, tools or attachments. Do not use this product for a purpose for which
it was not intended.
The warnings and cautions discussed in this instruction sheet cannot cover all possible conditions
and situations that may occur. It must be understood by the operator that common sense and
caution are factors which cannot be built into this product, but must be supplied by the operator.
OPERATING INSTRUCTIONS
The Jaws are reversible to ensure proper grip on a wide range of jobs. Depending on the depth
of the pulling job, keep either the longer or shorter ends of the Jaws down to grip the underside
of the bearing/pulley.
Hand tighten the Lead Screw through the bearing/pulley and onto the shaft from which the bear-
ing/pulley is to be removed. Once in position, wrench tighten the Lead Screw until the bearing/
pulley is completely free of the shaft.
INSPECTION, MAINTENANCE, AND CLEANING
Before each use, inspect the general condition of the Gear Puller. Check misalignment, binding
of moving parts, broken parts, and any other condition that may affect its safe operation. If any
malfunction of the parts occur, discontinue using the Gear Puller immediately and have the
problem corrected before further use. Do not use damaged equipment.
Keep the Gear Puller clean for better and safer product performance. To clean, use a mild
detergent or mild solvent. Then dry.
Note:
Replacement parts are not available for this item.
4.
5.
6.
7.
1.
2.
1.
2.
-
1
-
2
Harbor Freight Tools GEAR PULLER-THREE JAW User manual
- Type
- User manual
- This manual is also suitable for
Ask a question and I''ll find the answer in the document
Finding information in a document is now easier with AI
Related papers
-
Harbor Freight Tools 9 Speed Vertical Milling Machine Owner's manual
-
Central Machinery 93212 User manual
-
-
-
-
-
-
-
-
Other documents
-
Central Hydraulics 66657 Set Up And Operating Instructions Manual
-
Central Pneumatic Item 94585 Owner's manual
-
Chicago Electric 66891 User manual
-
Pittsburgh Automotive 64982 Owner's manual
-
Gear Head Lathe 65044 User manual
-
-
-
U.S. General 15 PIECE SLIDE HAMMER SET Assembly and Operating Instructions
-
-
