Renkforce FS5020E Owner's manual

Brand: Renkforce

Model: FS5020E

Type: Owner's manual

Page is loading ...

• Laser radiation can be dangerous, if the laser beam or its reection enters

unprotected eyes. Therefore, before using the laser equipment, familiarise yourself

with the statutory regulations and instructions for operating such a laser device.

• Never look into the laser beam and never point it at people or animals. Laser

radiation can seriously damage your eyes.

• If laser radiation enters your eyes, close your eyes immediately and move your

head away from the beam.

• If your eyes have been irritated by laser radiation, do not continue to carry out

tasks with safety implications, such as working with machines, working from

great heights or close to high voltage. Also, do not operate any vehicles until the

irritation has completely subsided.

• Do not point the laser beam at mirrors or other reective surfaces. The uncontrolled,

reected beam may strike people or animals.

• Never open the device. Setting or maintenance tasks must only be executed by a

trained specialist familiar with potential hazards. Improperly executed adjustments

might result in dangerous laser radiation.

• Caution - if operation settings or procedures other than those described in these

instructions are used, it could lead to exposure to dangerous radiation.

• Warning! This is a Class A device. This device may cause radio interference in

living quarters; in this case, appropriate measures may be required of the operator.

• Consult an expert when in doubt about operation, safety or connection of the

device.

• Maintenance, modications and repairs are to be performed exclusively by an

expert or at a qualied shop.

• If you have questions which remain unanswered by these operating instructions,

contact our technical support service or other technical personnel.

Operating elements

1 LED control indicator

2 Reader unit / Laser aperture

3 Screw

4 USB plug

5 Stand

Installation

Exercise caution when setting down the product. Despite the rubber feet, the device

may cause scratching on surfaces due to the feet’s corners.

1. Place the toothed lock washer on the screw (3).

2. Align one of the two openings on the arm of the stand (5) with the screw hole on the side of

the barcode scanner.

3. Fasten the barcode scanner to the stand (5) using the provided screw (3). Turn the screw

clockwise to fasten.

Operation

Risk of injury!

Never point the laser (2) at persons or animals. Lasers are dangerous.

Before using the barcode scanner, review the information on scanner settings under “Settings”.

1. Remove the protective foil from the reader unit (2).

2. Connect the USB plug (4) to a USB port on your computer.

3. On your PC, open a document you want to scan the barcode to. The barcode will be

inserted at the cursor’s position.

Operating instructions

Laser Barcode Scanner 1D + Stand

Item no. 407978

Intended use

Use this barcode scanner to quickly and reliably scan common barcodes such as UPC or EAN.

The scanned codes can be immediately inserted into documents and forms on a connected

computer. The barcode scanner is ideal for use in businesses, warehouses or ofces.

It is intended for indoor use only. Do not use it outdoors. Contact with moisture, e.g. in

bathrooms, must be avoided under all circumstances.

For safety and approval purposes, you must not rebuild and/or modify this product. If you use

the product for purposes other than those described above, the product may be damaged.

In addition, improper use can cause hazards such as short circuiting, re, electric shock etc.

Read the instructions carefully and keep them. Make this product available to third parties only

together with its operating instructions.

This product complies with the statutory national and European requirements. All company

Delivery content

• Laser barcode scanner

• Brief instructions

• Operating instructions

Latest operating instructions

Download the latest operating instructions via the link www.conrad.com/downloads or scan the

QR code shown. Follow the instructions on the website.

Explanation of symbols

The lightning symbol inside a triangle is used when there is a potential risk of

personal injury, such as electric shock.

An exclamation mark in a triangle indicates important instructions in this operating

manual that absolutely have to be observed.

The arrow symbol indicates specic tips and advice on operation.

Safety instructions

Read the operating instructions carefully and especially observe the safety

information. If you do not follow the safety instructions and information

on proper handling in this manual, we assume no liability for any resulting

personal injury or damage to property. Such cases will invalidate the warranty/

guarantee.

a) General

• The device is not a toy. Keep it out of the reach of children and pets.

• Do not leave packaging material lying around carelessly. This may become

dangerous playing material for children.

• Protect the product from extreme temperatures, direct sunlight, strong jolts, high

humidity, moisture, ammable gases, vapours and solvents.

• Do not place the product under any mechanical stress.

• If it is no longer possible to operate the product safely, take it out of operation and

protect it from any accidental use. Safe operation can no longer be guaranteed

if the product:

- is visibly damaged,

- is no longer working properly,

- has been stored for extended periods in poor ambient conditions or

- has been subjected to any serious transport-related stresses.

• Please handle the product carefully. Jolts, impacts or a fall even from a low height

can damage the product.

• Also observe the safety and operating instructions of any other devices which are

connected to the product.

• When operating the laser equipment, always make sure that the laser beam is

directed so that no one is in the projection area and that unintentionally reected

beams (e.g., from reective objects) cannot be directed into areas where people

are present.

• The product is equipped with a class 1 laser.

This is a publication by Conrad Electronic SE, Klaus-Conrad-Str. 1, D-92240 Hirschau (www.conrad.com).

All rights including translation reserved. Reproduction by any method, e.g. photocopy, microlming, or the

capture in electronic data processing systems require the prior written approval by the editor. Reprinting, also in

part, is prohibited. This publication represent the technical status at the time of printing.

4. Hold the reader unit (2) at a sufcient distance and correct angle (about 40°) to the barcode.

Depending on the size and type of barcode, you may need to adjust the distance. View the

following illustration, it depicts the reader unit’s correct position:

5. The barcode scanner has a motion sensor that automatically activates the reader unit (2).

A beep sounds and the LED control indicator blinks yellow if scanning was successful. The

barcode is scanned automatically. If the barcode cannot be read, the LED control indicator

blinks red.

Tips & notes

• Make sure that the barcode to be scanned is clean.

• The barcode to be scanned must be fully visible.

• Hold the scanner at the correct angle and distance.

• Hold the reader unit horizontal to the barcode.

• Check the settings each time you turn on the device to prevent incorrect readings.

Settings

You can congure the barcode scanner to your eld of application. The required barcodes are

available in the included additional brief instructions.

To make these settings, scan the corresponding barcode with the barcode scanner.

Restore factory settings:

You can restore the barcode scanner to factory settings by scanning the barcode

“Default”. A beep sounds.

Symbologies:

All barcode symbologies are activated by default. You can deactivate them

individually.

Overview of settings

A beep sounds if the setting was successful.

Some of the barcodes are listed twice in the instructions noted with ENABLE or

DISABLE:

ENABLE = activate function

DISABLE = deactivate function

Setting Function

Reading

SINGLE SCAN Scan once, the laser turns off after scanning.

SINGLE SCAN NO TRIGGER &

LASER TIMEOUT - 5 SECONDS

The laser stays on for 5 seconds and turns off

after scanning.

SINGLE SCAN NO TRIGGER &

LASER TIMEOUT - 2 SECONDS

The laser stays on for 2 seconds and turns off

after scanning.

Double check

CODE 11, CODE 39, CODE 93, CODE

128, CODABAR, I2OF5, ID2OF5, MSI,

UPC/EAN

DOUBLE CHECK - ENABLE /

DISABLE

The scanner reads the barcode twice with an

automatic comparison. In case of a match, the

result is transferred to the computer.

Image

REVERSE IMAGE - ENABLE /

DISABLE

By default, scans black-on-white barcodes.

This function activates scanning of white-on-

black barcodes.

Code ID

SEND BAR CODE ID - DISABLE Deactivates transmission of barcode ID.

SEND BAR CODE ID - RESET Resets barcode ID.

SEND BAR CODE ID - AS A PREFIX Inserts barcode ID as prex.

SEND BAR CODE ID - AS A SUFFIX Inserts barcode ID as sufx.

Keyboard language setting (country language setting)

Set keypad language (for alphanumeric barcodes i.e. Code 128):

DENMARK, FINLAND, FRANCE, GERMANY, ITALY, LATIN AMERICA, NETHERLANDS,

NORWAY, POLAND, SPAIN, SWITZERLAND, SWITZERLAND, SWEDEN, UNITED

KINGDOM, UNIVERSAL, UNITED STATES

Symbologies On/Off [ 1 ]

CODE 11 - ENABLE / DISABLE Activate/deactivate symbology CODE 11.

CODE 39 - ENABLE / DISABLE Activate/deactivate symbology CODE 39.

FULL ASCII - ENABLE / DISABLE Activate/deactivate symbology FULL ASCII.

CODE 93 - ENABLE / DISABLE Activate/deactivate symbology CODE 93.

CODE 128 - ENABLE / DISABLE Activate/deactivate symbology CODE 128.

CODE 128 ISBT - ENABLE / DISABLE Activate/deactivate symbology CODE 128 ISBT.

CODABAR - ENABLE / DISABLE Activate/deactivate symbology CODABAR.

Symbologies On/Off [ 2 ]

I2OF5 - ENABLE / DISABLE Activate/deactivate symbology I2OF5.

ID2OF5 - ENABLE / DISABLE Activate/deactivate symbology ID2OF5.

MSI - ENABLE / DISABLE Activate/deactivate symbology MSI.

UPC-A ENABLE / DISABLE Activate/deactivate symbology UPC-A.

UPC-E ENABLE / DISABLE Activate/deactivate symbology UPC-E.

EAN-13 ENABLE / DISABLE Activate/deactivate symbology EAN-13.

EAN-8 ENABLE / DISABLE Activate/deactivate symbology EAN-8.

Care and cleaning

• Disconnect the product from the power supply before cleaning.

• The product requires no servicing on your part aside from occasional cleaning.

• Do not use any aggressive cleaning agents, rubbing alcohol or other chemical solutions as

they can cause damage to the housing and malfunctioning.

• Clean the product with a dry, ber-free cloth.

• Do not scratch the protective glass of the reader unit (2).

• Do not immerse the product in water.

Disposal

Electronic devices are recyclable waste and must not be disposed of in the

household waste. At the end of its service life, dispose of the product according to

the relevant statutory regulations.

You thus full your statutory obligations and contribute to the protection of the

environment.

Technical data

Operating voltage ......................... 5 V/DC

Power consumption ...................... max. 500 mA

Laser class ................................... Class 1

Scan speed ................................... 100 scans per second

Highest resolution ......................... 4 mils (Code 39)

Cable length ................................. 2 m

Operating conditions ..................... 0 to +50 °C, 10 – 85 % RH (non-condensing)

Storage conditions ........................ -20 to +60 °C, 10 – 85 % RH (non-condensing)

System requirements .................... Windows

2000, XP (Home, Pro, with SP1, SP2, SP3),

only 32 bits, Vista™ (32 / 64 bits), 7 (32 / 64 bits), 8, 8 Pro,

Enterprise, RT (requires OTG support), Mac OS X 10.8

(Mountain Lion)

Symbologies ................................. CODE 11, CODE 39, CODE 93, CODE 128, CODABAR,

I2OF5, ID2OF5, MSI, UPC/EAN/JAN, ISBN

Dimensions (W x H x D) ............... 54 x 30 x 60 mm

Weight .......................................... 182 g

Page is loading ...

Renkforce FS5020E Owner's manual

Brand: Renkforce

Model: FS5020E

Type: Owner's manual

Download PDF

report

in other languages

français: Renkforce FS5020E Le manuel du propriétaire
Deutsch: Renkforce FS5020E Bedienungsanleitung
Nederlands: Renkforce FS5020E de handleiding

Renkforce FS5020E Owner's manual

Renkforce FS5020E Owner's manual

in other languages

Related papers

Other documents