MANUZOID
Explore
Explore
Bookmarks
Siemens
LC98GB540B
Siemens LC98GB540B Owner's manual
Type
Owner's manual
Brand
Siemens
Size
1.26 MB
Category
Cooker hoods
Pages
12
Language
English
Table of contents
Ú Table of contents[en] Instructions for installation and use
2
Instruction manual
2
Produktinfo
2
To book an engineer visit and product advice
2
Environmental protection
2
: Safety information
2
General information
2
Danger of suffocation!
2
Installation
3
Danger to life! Risk of poisoning!
3
Risk of fire!
3
Caution!
3
Risk of electric shock!
3
Risk of fire, risk of injury!
3
Risk of injury!
3
Risk of injury!
3
Using the appliance
3
Risk of burns!
3
Risk of injury, risk of damage!
3
Risk of fire, risk of burns!
3
Risk of burns, risk of damage!
3
Risk of fire!
3
Caution!
3
Risk of injury!
3
Cleaning and care
4
Risk of burns, risk of electric shock!
4
Caution!
4
Maintenance and repair
4
Risk of fire, risk of injury!
4
Risk of injury!
4
Risk of fire, risk of injury!
4
Risk of burns, risk of electric shock!
4
Operating modes
4
Exhaust air mode
4
Note
4
Circulating-air mode
4
Note
4
Operation
4
Note
4
Control panel variant 1
4
Control panel variant 2
5
Control panel variant 3
5
Switching on the fan: variant 1
5
Intensive setting
5
Switching on the fan: variants 2 and 3
5
Lighting
5
Installing and removing the filter
5
: Risk of burns, risk of electric shock!
5
Removing metal mesh grease filter
5
1. Open the lock and fold down the metal mesh grease filter.
5
2. Take the metal mesh grease filter out of the holder.
5
With edge extraction
5
1. Pull metal mesh grease filter downwards.
5
2. Take the metal mesh grease filter out of the holder.
5
Notes
5
Installing the metal mesh grease filter
5
1. Insert the metal mesh grease filter.
5
2. Fold up the metal mesh grease filter, locking it in place.
5
Cleaning and care
6
: Risk of burns, risk of electric shock!
6
Caution!
6
Cleaning the appliance surface
6
Note
6
Cleaning the metal mesh grease filters
6
Notes
6
In the dishwasher:
6
Note
6
By hand:
6
Note
6
Replacing bulbs
6
: Risk of burns, risk of electric shock!
6
Replacing halogen bulbs
6
Note
6
1. Carefully remove the bulb ring using a suitable tool.
6
2. Pull out the bulb and replace it with a bulb of the same type.
6
3. Insert the bulb cover.
6
4. Insert the mains plug or switch on the fuse again.
6
Replacing filament bulbs
6
1. Lift the bulb cover slightly and push towards the outside of the appliance.
6
2. Unscrew the bulb and replace it with a bulb of the same type.
6
3. Insert the bulb cover.
6
4. Insert the mains plug or switch on the fuse again.
6
LED lights
6
: Risk of injury!
6
Installation instructions
7
Installation instructions
7
Safety information
7
: Danger to life! Risk of poisoning!
7
: Risk of fire!
7
: Risk of electric shock!
7
: Risk of injury!
7
: Risk of injury!
7
Installation
8
Pipe dimensions
8
Note
8
Checking the wall
8
Preparing for installation
8
1. Mark a vertical centre line on the wall from the ceiling to the lower edge of the extractor hood.
8
2. Mark the positions for the screws and the contour of the attachment area.
8
3. Drill five 8 mm Ø holes to a depth of 80 mm for the attachments and press in the wall plugs flush with the wall.
8
Installation
8
1. Screw on the fixing bracket for the flue duct. ¨
8
2. Screw on brackets for the extractor hood hand-tight, max. 3 Nm.©
8
3. Screw in threaded pin, leaving it protruding out of the wall by 5 - 9 mm..ª
9
Attaching and aligning the appliance
9
1. Initially remove the protective foil from the back of the appliance and, following installation, remove the foil completely.
9
2. When attaching the appliance, ensure that it engages firmly with the brackets. «
9
3. Align the appliance horizontally by turning the brackets. If required, the appliance can be moved to the right or left. ¬
9
Securing the appliance
9
1. Press the safety caps with the arrow upwards onto the brackets until they engage. ®
9
2. Screw on the knurled nut and washer firmly. ¯
9
Removing the safety caps
9
Connecting the pipes
10
Note
10
Exhaust-air pipe Ø 120 mm
10
1. Attach the reducing connector directly to the air-pipe connector.
10
2. Attach the exhaust air pipe to the reducing connector.
10
3. Seal both joints appropriately.
10
Electrical connection
10
: Risk of electric shock!
10
Attaching the flue duct
10
: Risk of injury!
10
1. Separate the flue ducts.
10
2. Remove the protective foil from both flue ducts.
10
3. Push one flue duct into the other.
10
Notes
10
4. Place the flue ducts on the appliance.
10
5. Push the inner flue duct upwards and attach it to the fixing brackets on the left and right. ¨
10
6. Press the flue duct downwards until it engages. ©
10
7. Screw the flue duct to the sides of the fixing bracket using two screws. ª
10
View document