MANUZOID
Explore
Explore
Bookmarks
Siemens
LC87KBM60/01
Siemens LC87KBM60/01 User manual
Type
User manual
Brand
Siemens
Size
1.09 MB
Category
Cooker hoods
Pages
20
Language
English
Table of contents
Extractor hood
1
Table of contents
2
en Instructions for installation and use
2
Instruction manual
2
8 Intended use
2
Intended use
2
( Important safety information
3
Important safety information
3
: Warning
3
Danger of suffocation!
3
: Warning
3
Danger of death!
3
: Warning
3
Risk of fire!
3
: Warning
4
Risk of burns!
4
: Warning
4
Risk of injury!
4
: Warning
4
Risk of injury!
4
: Warning
4
Hazard due to magnetism!
4
: Warning
4
Risk of electric shock!
4
Causes of damage
4
Caution!
4
7 Environmental protection
5
Environmental protection
5
Saving energy
5
Environmentally-friendly disposal
5
Ç Operating modes
5
Operating modes
5
Exhaust air mode
5
Note:
5
Circulating-air mode
5
Note:
5
1 Operating the appliance
6
Operating the appliance
6
Note:
6
Control panel
6
Symbol
6
Explanation
6
Setting the fan
6
Switching on
6
Selecting the fan setting
6
Switching off
6
Intensive setting
6
Switching on
6
Note:
6
Switching off
6
Lighting
6
2 Cleaning and maintenance
6
Cleaning and maintenance
6
: Warning
6
Risk of burns!
6
: Warning
6
Risk of electric shock!
6
: Warning
6
Risk of electric shock!
6
: Warning
6
Risk of injury!
6
: Warning
6
Risk of injury!
6
Cleaning agents
6
Note:
6
Note:
6
Area
7
Cleaning products
7
Removing the metal grease filter
7
Note:
7
1. Slowly open the stainless steel flap. Ensure that the stainless steel flap does not swing out after it is released.
7
2. Open the lock and swing down the metal grease filter. When you do this, take hold of the metal grease filter from underneath with your other hand.
7
3. Take the metal grease filter out of the holder.
7
Notes
7
Cleaning the metal mesh grease filters
7
: Warning
7
Risk of fire!
7
Notes
7
By hand:
7
Note:
7
In the dishwasher:
7
Note:
7
Installing the metal mesh grease filter
8
: Warning
8
Risk of injury!
8
Notes
8
1. Insert the metal grease filter and lock it in place. When you do this, take hold of the metal grease filter from underneath with your other hand.
8
Note:
8
2. If the metal grease filter has not been inserted correctly, open the lock and reinsert the metal grease filter correctly.
8
3 Trouble shooting
8
Trouble shooting
8
: Warning
8
Risk of electric shock!
8
Malfunction table
8
Problem
8
Possible cause
8
Solution
8
LED lights
8
: Warning
8
Risk of injury!
8
4 Customer service
9
Customer service
9
To book an engineer visit and product advice
9
Accessories
9
Note:
9
Note:
9
Accessories
9
Order number
9
Installation instructions
10
Note:
10
( Important safety information
11
Important safety information
11
: Warning
11
Risk of fire!
11
: Warning
11
Risk of death!
11
: Warning
11
Danger of death!
11
: Warning
12
Danger of death!
12
: Warning
12
Risk of injury!
12
: Warning
12
Risk of injury!
12
: Warning
12
Hazard due to magnetism!
12
: Warning
12
Risk of electric shock!
12
: Warning
12
Risk of electric shock!
12
: Warning
12
Danger of suffocation!
12
K General information
13
General information
13
Checking the wall
13
Electrical connection
13
: Warning
13
Risk of electric shock!
13
: Warning
13
Risk of electric shock!
13
5 Installation
13
Installation
13
Preparing the appliance
13
1. Pull back the adhesive strip from the stainless steel flap and open the stainless steel flap. Do not completely pull the adhesive strip off from the appliance.
13
2. Remove the polystyrene foam and metal grease filter from the appliance.
13
3. Install the metal grease filter in the appliance.
13
4. Close and secure the stainless steel flap. Use the adhesive strip to do this.
13
Note:
13
Preparing the installation
14
Caution!
14
1. Determine where the extractor hood should be positioned and lightly mark where the lower edge of the appliance should be on the wall. In doing so, determine where the middle should be based on the hob.
14
Note:
14
2. Place the template against the line drawn on the wall and fasten it in place. Mark where the screws should be inserted.
14
3. Drill 8 mm diameter holes to a depth of 80 mm for fastening the appliance, remove the template and press in the wall plugs flush with the wall.
14
Fitting with a flue duct
14
Fitting without a flue duct
14
Installation
15
Wall-mounting the appliance and levelling it
15
1. When mounting the appliance, ensure that it engages properly with the mounting supports.
15
2. If required, the appliance can be moved to the right or to the left.
15
3. Firmly tighten the screws for the mounting supports. Hold the bracket firmly when doing so. ¨
15
4. If no duct is fitted, screw in the two locking screws without the bracket. ©
15
5. Completely remove the adhesive strip.
15
Connecting the pipes
15
Note:
15
Exhaust air pipe, dia. 120 mm
15
1. Fit the reducing connector directly to the air-pipe connector.
15
2. Attach the exhaust air pipe to the reducing connector.
15
3. Use suitable means to seal both joints.
15
Attaching the flue duct
15
: Warning
15
Risk of injury!
15
: Warning
15
Risk of electric shock!
15
1. Separate the flue duct sections by removing the adhesive tape.
15
2. Remove the pieces of protective film from both flue duct sections.
15
3. Push one flue duct section into the other.
15
Notes
15
4. Place flue ducts sections on the appliance.
15
5. Slide the inner flue duct section upwards, attach it to the left and right sides of the retaining bracket, and then slide it down to engage it. ¨
15
6. Screw the flue duct section to the sides of the retaining bracket using two screws. ©
16
7. Clip the lower flue duct section in at the retaining bracket. The connection cable must not be damaged. ª
16
Note:
16
View document