MANUZOID
Explore
Explore
Bookmarks
Motorola
TLKR T80
Motorola TLKR T80 Owner's manual
Type
Owner's manual
Brand
Motorola
Size
4.13 MB
Category
Two-way radios
Pages
14
Language
English
Table of contents
Product Safety and RF Exposure for Portable Two-Way Radios
3
Attention!
3
Package Contents
3
Frequency Chart
3
Features and Specifications
3
Control and Functions
4
Display
5
1. Silent Indicator
5
2. Transmit Indicator
5
3. Receive Indicator
5
4. Dual Watch Indicator
5
5. Auto Power Off Indicator
5
6. Key Lock Indicator
5
7. Scan Indicator
5
8. Channel Indicator
5
9. Battery Level Meter
5
10. Group Indicator
5
11. VOX/Room Monitor Indicator
5
12. Call Indicator
5
13. Sub-code (Group ID/Code) Indicator
5
14. Colon (for Up Timer)
5
Installing the Battery
5
1. Make sure your radio is turned OFF.
5
2. For T80: To remove the battery compartment door, press the tab at the bottom of the compartment door. For T80 Extreme : To remove the battery compartment door, use a coin to wedge the battery door open.
5
3. Install the NiMH batteries into the battery compartment.
5
4. Replace the battery compartment door.
5
Battery Level and Low Battery Alert
5
Charging the Radio
5
1. Make sure your radio is turned OFF.
5
2. Connect the AC adapter to the radio’s DC IN 9V. Connect the other end of the AC adapter to a vehicle accessory power outlet.
5
3. Charge the battery pack for 14 hours.
5
1. Make sure your radio is turned OFF.
5
2. Connect the AC adapter to the DC IN 9V of the charging cradle.
5
3. Place the charging cradle on a stable surface.
5
4. Place the radio in the charging cradle with the keypad facing forward.
5
5. LED indicator will illuminate and remain illuminated as long as the radio is in the charger.
6
1. Remove the rechargeable NiMH battery pack from the radio.
6
2. Place the battery support bracket into the charging cradle.
6
3. Install the NiMH battery pack into the charging cradle. Ensure that the charging contacts are correctly aligned.
6
4. LED indicator will illuminate and remain illuminated as long as the radio is in the charger.
6
Basic Radio Operations
6
Turning your Radio On/Off
6
Adjusting the Volume
6
Adjusting the Sound (Key Beeps)
6
Navigating through the Menu
6
1. To enter the Select Menu, press the SEL/ button.
6
2. To enter the Common Menu, press the MENU/GRP button.
6
3. Additional presses of the SEL/ button or MENU/GRP button will advance you through the Menu.
6
4. To exit the Menu function, do one of the following :
6
a. Press the MENU/GRP button,
6
b. Press the PTT button
6
c. Wait 10 seconds until the unit automatically returns to “Normal” mode.
6
Talking on Your Radio
6
1. Hold your radio 5–8 cm from your mouth.
6
2. Press and hold the PTT button while speaking. The appears on the display.
6
3. Release the PTT button. You can now receive incoming calls. When you do, the appears on the display. To respond, repeat procedure from step 1.
6
Selecting a Channel and a Sub-Code
6
1. SEL/ button to enter Select Menu. Advance until the Channel indicator blinks.
6
2. or to the required channel.
6
1. SEL/ button to enter Select Menu. Advance until the Sub-code indicator blinks.
6
2. or to the required Sub-code.
6
3. Exit the Select Menu.
6
Select Menu
7
Voice Operated Transmission (VOX)
7
1. MENU/GRP button to enter Common Menu. Advance and select “VOX”.
7
2. SEL/ to select.
7
3. or to the desired VOX sensitivity level.
7
4. Exit the Select Menu.
7
Transmitting a Call Tone
7
1. MENU/GRP button to enter Common Menu. Advance to “TONE”.
7
2. SEL/ to select.
7
3. or to the desired call tone.
7
4. Exit the Common Menu.
7
1. to transmit the selected call tone. The selected tone will automatically be transmitted for a fixed length of time.
7
2. PTT to cancel Call Tone.
7
Auto Power Off
7
1. MENU/GRP button to enter Common Menu. Advance until “PWR” and the current Auto Power Off time blinks.
7
2. SEL/ to select.
7
3. or to select the time from ON, 1H, 2H, and 3H.
7
4. Exit the Menu.
7
Common Menu
8
Group Menu
8
1. Press and hold MENU/GRP to enter GROUP MENU.
8
2. or to proceed to each menu (GRP/CODE/RING/ID).
8
3. SEL/ to select.
8
4. or to proceed to desired condition or number.
8
5. SEL/ to select.
8
6. MENU/GRP to exit.
8
Set Group Mode
8
1. Press and hold MENU/GRP to enter GROUP MENU.
8
2. SEL/ to control Group Mode.
8
3. or to “Y”. SEL/ to go to Group Menu and Group Code Setting.
8
4. or to “N”. SEL/ to exit from Group Menu.
8
Set Group Code
9
1. or to choose the Group Code.
9
2. SEL/ to complete Group Code setting.
9
3. The radio enters “Ring Tone Setting Menu”
9
4. MENU/GRP to back to Group Menu.
9
Set Ring Tone
9
1. or to select a Ring Tone.
9
2. The selected Ring Tone sounds.
9
Set ID
9
1. or to select an ID number.
9
2. If the ID is already taken, USED is seen. If USED is not shown, then the ID is available.
9
3. SEL/ to advance to setting ID Name.
9
Set ID Name
9
1. or to select a character that will blink on the display.
9
2. SEL/ to select and move to the next character.
9
3. SEL/ to register the ID number and ID Name.
9
Channel Setting in Group Mode
9
1. MENU/GRP to enter Group Mode.
9
2. SEL/ to enter Channel Setting.
9
3. or to “Auto Channel Change Setting”.
9
4. SEL/ to select. A channel number will blink and “ALL” is seen.
9
5. or to select the channel.
9
6. SEL/ or to transmit Auto Channel Change command.
9
7. MENU/GRP to return to Channel Setting in Group Mode.
9
1. MENU/GRP to enter Group Mode.
9
2. SEL/ to enter Channel Setting.
9
3. or to “Manual Channel Setting”.
9
4. SEL/ to select. A channel number will blink and “MY” is seen.
9
5. or to select the channel manually.
9
6. SEL/ to exit from Manual Channel setting.
9
7. MENU/GRP to return to Channel Setting in Group Mode.
9
Set All Call
9
1. MENU/GRP to enter Group Mode.
9
2. to enter All/ Direct Call Setting.
9
3. or to select All Call Transmission. “SYNC” is seen.
9
4. SEL/ or to exit this setting, and transmit All Call. All Call Tone sounds. and blinks while transmitting.
9
5. MENU/GRP to exit.
9
Set Direct Call
10
1. MENU/GRP to enter Group Mode.
10
2. to enter All/ Direct Call Setting.
10
3. or to select an ID Number.
10
4. or SEL/ to transmit Direct Call Command. The selected Call Tone sounds. The display shows TX icon and CALL icon while transmitting.
10
5. MENU/GRP to go back to All/Direct Call setting.
10
Features on Your Radio
10
Channel Scan Mode
10
1. MENU/GRP to enter Common Menu. Advance to ”SCAN”.
10
2. SEL/ to turn ON channel scan.
10
3. MENU/GRP or PTT to turn OFF Scan mode.
10
Dual Watch Mode
10
1. MENU/GRP to enter Common Menu. Advance to “2CH”.
10
2. or to select the channel, then press SEL/ .
10
3. or to select the Sub-code, then press SEL/ .
10
4. The radio starts to Dual Watch.
10
5. MENU/GRP to turn the Dual Watch mode OFF.
10
Room Monitor
10
1. MENU/GRP to enter Common Menu. Advance to “ROOM”.
10
2. SEL/ to select.
10
3. or to the desired room monitor sensitivity level.
10
4. SEL/ to turn ON room monitor. MENU/GRP to turn OFF Room Monitor.
10
Silent Mode
10
1. MENU/GRP to enter Common Menu.
10
2. Select “SLNT”.
11
3. SEL/ to select.
11
4. to turn Silent Mode ON. “Y” is displayed on the Channel Indicator. appears.
11
5. to turn Silent Mode OFF. “N” is displayed on the Channel Indicator. disappears.
11
Up Timer
11
1. MENU/GRP to enter Common Menu. Advance to “TIME”.
11
2. SEL/ to select the Up Timer.
11
3. SEL/ to start the Up Timer.
11
4. SEL/ to pause the Timer. SEL/ to ON/OFF the Timer.
11
5. MENU/GRP or PTT to stop or reset up timer.
11
Key Lock
11
LCD Backlight
11
Monitor Mode
11
1. Press the MON button for brief listening. The icon blinks.
11
2. Press and hold the MON button for 2 seconds for continuous listening. The icon continues to blink.
11
Roger Beep
11
LED Torch
11
Approved Accessories
11
Warranty Information
12
What Is Not Covered By The Warranty
12
Copyright Information
12
View document
Motorola TLKR T80 Setup & User Manual
Type
Setup & User Manual
Brand
Motorola
Size
3.01 MB
Category
Two-way radios
Pages
165
Language
Danish, German, English, Spanish, Finnish, French, Italian, Dutch, Norwegian, Polish, Portuguese, Swedish, Turkish
View document