MANUZOID
Explore
Explore
Bookmarks
Bosch
DIB12T151/01
Bosch DIB12T151/01 Operating instructions
Type
Operating instructions
Brand
Bosch
Size
2.69 MB
Category
Cooker hoods
Pages
12
Language
English
Table of contents
[en] Instructions for installation and use
1
Ú Table of contents[en] Instructions for installation and use
2
Instruction manual
2
Produktinfo
2
To book an engineer visit and product advice
2
Environmental protection
2
m Safety instructions
2
General information
2
Danger of suffocation!
2
Installation
3
Mortal danger, risk of intoxication!
3
Risk of fire!
3
Caution!
3
Risk of electric shock!
3
Risk of fire, risk of injury!
3
Risk of injury!
3
Risk of injury!
3
Using the appliance
3
Risk of burns!
3
Risk of injury, risk of damage!
3
Risk of fire, risk of burns!
3
Risk of burns, risk of damage!
3
Risk of fire!
3
Caution!
3
Risk of injury!
3
Cleaning and care
4
Risk of burns, risk of electric shock!
4
Caution!
4
Maintenance and repair
4
Risk of fire, risk of injury!
4
Risk of injury!
4
Risk of fire, risk of injury!
4
Risk of burns, risk of electric shock!
4
Operating modes
4
Exhaust air mode
4
Note
4
Circulating-air mode
4
Note
4
Operation
5
Note
5
Control panel variant 1
5
Control panel variant 2
5
Setting the fan
5
Manual mode
5
Automatic mode
5
Sensor control
5
1. When the fan is switched off, hold down button ) for 4 seconds. The setting is displayed.
5
2. The setting of the sensor control is changed by pressing the + or – button again.
5
3. To acknowledge the inputs, hold down the ) button for 4 seconds.
5
Intensive setting
5
Switching on fan run-on
5
Light
5
Saturation displays
5
Acoustic signal
5
Installing and removing filter
6
m Risk of burns, risk of electric shock!
6
Removing metal-mesh grease filter
6
1. Open lock and fold down the metal-mesh grease filter.
6
2. Take metal-mesh grease filter out of the holder.
6
With edge extraction
6
1. Pull metal-mesh grease filter downwards.
6
2. Take metal-mesh grease filter out of the holder.
6
Notes
6
Installing metal-mesh grease filter
6
1. Insert metal-mesh grease filter.
6
2. Fold up metal-mesh grease filter and lock.
6
Cleaning and care
6
m Risk of burns, risk of electric shock!
6
Caution!
6
Cleaning appliance surface
6
Note
6
Cleaning metal-mesh grease filters
6
Notes
6
In the dishwasher:
6
Note
6
By hand:
6
Note
6
Replacing bulbs
7
m Risk of burns, risk of electric shock!
7
Replacing halogen bulbs
7
Note
7
1. Carefully remove bulb ring using a suitable tool.
7
2. Pull out bulb and replace with bulb of the same type.
7
3. Insert bulb cover.
7
4. Insert mains plug or switch on fuse again.
7
Replacing filament bulbs
7
1. Lift bulb cover slightly and push towards the outside of the appliance.
7
2. Unscrew bulb and replace with bulb of the same type.
7
3. Insert bulb cover.
7
4. Insert mains plug or switch on fuse again.
7
LED lights
7
m Risk of injury!
7
Installation instructions
8
Safety notes
8
m Mortal danger, risk of intoxication!
8
m Risk of fire!
8
m Risk of electric shock!
8
m Risk of injury!
8
m Risk of injury!
8
Installation
9
Pipe dimensions
9
Note
9
Preparing the ceiling
9
Attaching upper support frame
9
1. Before installation, specify the total height of the support frame and mark the screw holes.
9
Note
9
2. On the ceiling mark the centre point of the appliance.
9
3. Using the enclosed template, mark the positions for the screws on the ceiling.
9
4. Drill four 8 mm Ø holes to a depth of 80 mm for the attachments and press in the wall plugs flush with the wall.
9
5. Attach the upper part of the support frame to the ceiling with 4 screws.
9
Note
9
Attaching lower support frame
9
Notes
9
Installing the appliance
9
1. Hook the appliance from below into the support frame.
9
Note
9
2. Attach the appliance to the support frame using 2 securing screws.
9
3. Hook in retaining clip and screw tight.
10
Connecting the pipes
10
Note
10
Exhaust-air pipe Ø 120 mm
10
1. Attach reducing connector directly to the air-pipe connector.
10
2. Attach exhaust air pipe to the reducing connector.
10
3. Seal both joints appropriately.
10
Electrical connection
10
m Risk of electric shock!
10
Attaching flue duct
10
m Risk of injury!
10
1. Separate the flue ducts.
10
2. Remove the protective foil from both sides.
10
3. Attach both parts of the upper flue to the appliance and push together.
10
Note
10
4. Push up the upper flue part and secure with 2 screws.
10
5. Insert both lower parts of the flue and push together.
10
View document