Adastra IW60B User manual

Brand: Adastra

Model: IW60B

Type: User manual

This manual is also suitable for

IW30B

Adastra IW60B is a discreet audio solution designed to power wall or ceiling mounted speakers. It allows you to stream music via Bluetooth from your smartphone or other Bluetooth-enabled devices. The unit is easily installed in a ceiling, wall, or on the surface and can be connected to speakers using the supplied wires. It features a 12Vdc power supply, Bluetooth 4.0 connectivity, and delivers 2 x 30W of power at 4Ω impedance. The IW60B also has auxiliary input and output options, allowing you to connect additional audio sources or daisy-chain multiple amplifiers.

IW60B

In-wall Bluetooth Amplifier

Item ref: 953.093UK

User Manual

Version 1.0

Caution: Please read this manual carefully before operating

Damage caused by misuse is not covered by the warranty

953.093UK User Manual

Introduction

Thank you for choosing the Adastra IW60B in-wall amplifier for your discreet audio

installation. This unit is designed to power wall or ceiling mounted speakers and receive

audio via Bluetooth. Please read this manual to gain the best results from your product and

avoid damage through misuse.

SAFETY SYMBOL AND MESSAGE CONVENTIONS

CAUTION

RISK OF ELECTRIC SHOCK

DO NOT OPEN

AVIS

RISQUE DE CHOC ELECTRIQUE NE PAS

OUVRIR

This symbol indicates that dangerous voltage constituting a risk of electric shock is

present within this unit

This symbol indicates that there are important operating and maintenance instructions in

the literature accompanying this unit.

Warning

To prevent the risk of fire or electric shock, do not expose any components to rain or moisture. If

liquids are spilled on the casing, stop using immediately, allow unit to dry out and have checked by

qualified personnel before further use. Avoid impact, extreme pressure or heavy vibration to the case.

No user serviceable parts inside – Do not open the case – refer all servicing to qualified service

personnel.

Safety

• Check for correct mains voltage before connecting the power adaptor

• Use only the power adaptor provided or an identical replacement

Placement

• The IW60B can be installed in a ceiling or stud wall to power flush or surface mount speakers

• The IW60B can also be surface mounted if necessary

• Ensure adequate ventilation for cooling and keep away from combustible material or moisture

• Ensure that the IW60B is within Bluetooth connection range of the sending device

Cleaning

• Use a soft cloth with a neutral detergent to clean the housing as required

• Use a vacuum cleaner to clear apertures and controls of any dust or debris build-ups

• Do not use solvents for cleaning the unit

953.093UK User Manual

Connections

Installation

Locate the IW60B in the ceiling, wall or on the surface required. Tabs at each end of the

housing can be used for securing with screws.

Connect speakers using the supplied wires or equivalent by connecting “+” and “-” on the

speaker to the relevant connection on the IW60B. The speaker connections are via screw

terminals on a Euroblock, which can be removed for easy access whilst making connections.

Important: Ensure that the load is no lower than 4Ω for each output.

(e.g. 2 x 4Ω speakers… or… 2 pairs of 8Ω speakers wired in parallel)

Ensure that the speakers can handle 30W from each output.

If the IW60B is to be used with a wired audio line level input (instead of Bluetooth), connect

this to the Euroblock terminals labelled “AUX IN” as shown on the Connections diagram

above.

Left positive connection (Left+) should be connected to “L”

Right positive connection (Right+) should be connected to “R”

Both negative connections (Left- and Right-) should be connected to “G”

(G is the terminal for Ground connection – common for both Left and Right signals)

Likewise, the Bluetooth or Aux input can be relayed to further IW60B or other amplifiers by

connecting a line level output from the Euroblock terminals labelled “AUX OUT”

AUX IN and AUX OUT connections should be made using shielded stereo audio cable and

not speaker cable.

953.093UK User Manual

Operation

When powered up, the IW60B will be open for Bluetooth pairing.

(a small LED will flash inside the housing)

Ensure that only the first IW60B in an AUX OUT-IN daisy chain is powered up initially.

This will ensure that all of the amps in the daisy chain receive the same audio.

Search available Bluetooth devices on your smart phone or other sending device for a device

with Bluetooth ID “IW60B-****” (where **** is a unique ID number for each unit)

Select to pair and connect with this ID (rename if required on Android)

When paired and connected, set the volume low on the smart phone or other sending

device and play a track to check the sound through the speakers

Power down the IW60B when not in use and isolate from the mains if not used for long

periods of time.

Specifications

Power supply

12Vdc, 3000mA (adaptor included)

Bluetooth version

4.0

Output: rms @ 4Ω

2 x 30W

Minimum impedance

4Ω per output

Speaker outputs

L-/L+/R-/R+ screw terminals (Euroblock)

Auxiliary input

L/G/R screw terminals (Euroblock)

Auxiliary output

L/G/R screw terminals (Euroblock)

Dimensions

124 x 40 x 27mm

Weight

68g (excluding power adaptor)

Disposal: The “Crossed Wheelie Bin” symbol on the product means that the product is classed as Electrical or

Electronic equipment and should not be disposed with other household or commercial waste at the end of its useful life.

The goods must be disposed of according to your local council guidelines.

Errors and omissions excepted.

Adastra IW60B User manual

Brand: Adastra

Model: IW60B

Type: User manual

This manual is also suitable for

IW30B

Download PDF

report

Adastra IW60B User manual

This manual is also suitable for

Adastra IW60B User manual

Related papers

Other documents