Zebra MX101 is an optional modular unit that replaces the MP6000 tower cover and is used for customer scanning. The unit can be installed on either the left or right side of the MP6000.
The MX101 CSS has the following capabilities:
- Customer scanning: The MX101 CSS allows customers to scan their own items at the checkout counter. This can help to speed up the checkout process and reduce wait times for customers.
- Easy installation: The MX101 CSS is easy to install and can be done in minutes. No special tools or expertise are required.
- Compact design: The MX101 CSS is compact and does not take up much space on the checkout counter.
Zebra MX101 is an optional modular unit that replaces the MP6000 tower cover and is used for customer scanning. The unit can be installed on either the left or right side of the MP6000.
The MX101 CSS has the following capabilities:
- Customer scanning: The MX101 CSS allows customers to scan their own items at the checkout counter. This can help to speed up the checkout process and reduce wait times for customers.
- Easy installation: The MX101 CSS is easy to install and can be done in minutes. No special tools or expertise are required.
- Compact design: The MX101 CSS is compact and does not take up much space on the checkout counter.
MX101 CUSTOMER
SIDE SCANNER (CSS)
INSTALLATION
GUIDE
2 MX101 Customer Side Scanner (CSS)
The MX101 CSS is an optional modular unit that replaces the MP6000 tower cover, and
is used for customer scanning. The unit can be installed on either the left, or right side
of the MP6000. Remove all hardware from the packaging.
Installing the MX101 on the Customer’s Right Side of the Tower Cover
To install the MX101 on the customer’s right side (default) of the MP6000:
1. Lift the MP6000 out of the checkstand, if already installed.
2. Remove the MP6000 tower bezel by squeezing inward on both the left and right
sides of the lower part of the tower bezel, pushing its side snaps to disengage.
Slide the tower bezel up and lift out.
NOTE Refer to the identification label instructions to affix the label to the MP6000;
refer to the MX101 Product Reference Guide (p/n 72E-171320-xx) for
information about programming the optional MX101 CSS.
Scan Window
CSS Tower Cover
USB Cable
Scan Window Cover
Identification
Label
CSS Blank Side Cover
Scan Module
xxxxxxxxxxx
Tower Bezel
Squeeze
Inward
Installation Guide 3
3. Remove the MP6000 tower cover by pulling the tabs on either side; then slide it
back to remove.
4. Remove the scan window cover from the CSS tower by squeezing the snaps
shown below.
5. Determine the side of the MP6000 to which the MX101 should be installed. The
default is the customer’s right side (the side of the MX101 tower cover already
open for the scan module to be inserted).
NOTE See Installing the MX101 on the Customer’s Left Side of the Tower Cover
beginning on page 7 to install the scan module on the customer’s left side of
the tower cover.
Tab(s)
(on each
side)
Snaps
4 MX101 Customer Side Scanner (CSS)
6. Insert the scan module into place facing out of the opening of the CSS tower
cover. Ensure the grommets on the scan module align with the sockets in the
tower cover, and push into place.
7. Snap the scan window cover into place on the tower, over the scan window.
Scan Module
CSS Tower
Cover
Grommets (3)
Grommet
Sockets
(3)
Module
Installed
Installation Guide 5
8. Connect the USB cable to the top USB port (recommended) on the MP6000.
Route the cable into the side cable slots as shown.
9. Route the cable, looping through the right side cable slots as shown below. (Cable
wire should be tight.)
Top USB Port
Side Cable Slots
Cable Slots
Service Loop
Cable Slots
6 MX101 Customer Side Scanner (CSS)
10. Connect the cable to the micro USB port at the bottom of the scan module.
Ensure the cable is clipped into the scan module plastic directly below the USB
port.
11. Slide the CSS tower cover back into place. Ensure the cable service loop folds up
into the blank space in the CSS tower cover, on the opposite side of the scan
module. Snaps should click together. When the tower cover is replaced, the
module locks into the grommet compression ribs on the MP6000.
Micro USB Port
Service
Loop
Scan Module Cable Clip
Installation Guide 7
12. Replace MP6000 tower bezel. Snap down into place.
Installing the MX101 on the Customer’s Left Side of the Tower Cover
To install the MX101 on the left side of the MP6000:
1. Push out the CSS blank side cover on the left side of the CSS tower cover, and
replace the cover into the opening on the right side of the tower cover.
2. Repeat steps 1, 2, 3, and 4 from Installing the MX101 on the Customer’s Right
Side of the Tower Cover beginning on page 2.
3. Insert the scan module into place facing out of the left side opening of the CSS
tower cover. Ensure the grommets on the scan module align with the sockets in
the tower cover, and push into place.
4. Snap the scan window cover into place on the tower, over the scan window.
5. Connect the USB cable to the top USB port (recommended) on the MP6000 and
route the cable through the side cable slots shown in step 8 on page 5.
8 MX101 Customer Side Scanner (CSS)
6. Route the cable, looping through the left side cable slots as shown below.
7. Connect the cable to the micro USB port on the bottom of the scan module.
Ensure the cable is clipped into the scan module plastic directly below the USB
port. (See step 10 on page 6 for illustration.)
8. Slide the CSS tower cover back into place. Ensure the cable service loop folds up
into the blank space in the CSS tower cover, on the opposite side of the scan
module. Snaps should click together. When the tower cover is replaced, the
module locks into the grommet compression ribs on the MP6000.
9. Replace MP6000 tower bezel. Snap down into place.
Cable Slots for Left
Side Installation
Scan Module
Cable Clip
MN000051A02 Revision A- January 2015
Zebra Technologies Corporation
Lincolnshire, IL U.S.A.
http://www.zebra.com
Zebra and the Zebra head graphic are registered trademarks of ZIH Corp. The
Symbol logo is a registered trademark of Symbol Technologies, Inc., a Zebra
Technologies company.
© 2015 Symbol Technologies, Inc.
-
1
-
2
-
3
-
4
-
5
-
6
-
7
-
8
Zebra MX101 is an optional modular unit that replaces the MP6000 tower cover and is used for customer scanning. The unit can be installed on either the left or right side of the MP6000.
The MX101 CSS has the following capabilities:
- Customer scanning: The MX101 CSS allows customers to scan their own items at the checkout counter. This can help to speed up the checkout process and reduce wait times for customers.
- Easy installation: The MX101 CSS is easy to install and can be done in minutes. No special tools or expertise are required.
- Compact design: The MX101 CSS is compact and does not take up much space on the checkout counter.
Ask a question and I''ll find the answer in the document
Finding information in a document is now easier with AI
Related papers
Other documents
-
Motorola MX101 Product Reference Manual
-
-
Sony CMT-101 Operating instructions
-
-
Campbell Hausfeld MP3236 User manual
-
Fujitsu PRIMERGY TX140 S1 Upgrade And Maintenance Manual
-
MINN KOTA RIPTIDE ULTERRA 80 Installation Instructions Manual
-
MINN KOTA Ultrex 1368800 Owner's manual
-
Black Diamond Equipment MP6000 User manual
-
Traxxas Stampede 4X4 Kit User manual